HyperX FURY Manual


Læs nedenfor 📖 manual på dansk for HyperX FURY (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
DESCRIPTION
HyperX HX316C10FBK2/16 is a kit of two 1G x 64-bit (8GB)
DDR3-1600 CL10 SDRAM (Synchronous DRAM) 2Rx8 memory
modules, based on sixteen 512M x 8-bit DDR3 FBGA compo-
nents per module. Total kit capacity is 16GB. Each module kit
has been tested to run at DDR3-1600 at a low latency timing of
10-10-10 at 1.5V. Additional timing parameters are shown in
the PnP Timing Parameters section below. The JEDEC stan-
dard electrical and mechanical specifications are as follows:
Document No. 4807008-001.B00 04/23/15 Page 1
SPECIFICATIONS
selcyc 01)DDI(LC
Row Cycle Time (tRCmin) 48.125ns (min.)
Refresh to Active/Refresh 260ns (min.)
Command Time (tRFCmin)
Row Active Time (tRASmin) 37.5ns (min.)
Maximum Operating Power TBD W* (per module)
0 - V 49gnitaR LU
Operating Temperature 0o C to 85o C
Storage Temperature -55o C to +100o C
*Power will vary depending on the SDRAM used.
FEATURES
JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
VDDQ = 1.5V (1.425V ~ 1.575V)
800MHz fCK for 1600Mb/sec/pin
8 independent internal bank
Programmable CAS Latency: 11, 10, 9, 8, 7, 6
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the y using A12 or
MRS]
Bi-directional Dierential Data Strobe
Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
On Die Termination using ODT pin
Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
Asynchronous Reset
Height 1.291(32.80mm) w/heatsink, double sided
component
HX316C10FBK2/16
16GB (8GB 1G x 64-Bit x 2 pcs.)
DDR3-1600 CL10 240-Pin DIMM Kit
Continued >>
kingston.com/hyperx
PnP JEDEC TIMING PARAMETERS:
DDR3-1600 CL10-10-10 @1.5V
DDR3-1333 CL9-9-9 @1.5V
DDR3-1066 CL7-7-7 @1.5V
Note: The PnP feature oers a range of speed and timing options to support
the widest variety of processors and chipsets. Your maximum speed will
be determined by your BIOS.


Produkt Specifikationer

Mærke: HyperX
Kategori: Ikke kategoriseret
Model: FURY

Har du brug for hjælp?

Hvis du har brug for hjælp til HyperX FURY stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret HyperX Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kramer

Kramer VP-8X8 Manual

25 November 2024
Kramer

Kramer PT-2C Manual

25 November 2024
Lazer

Lazer Bob+ Manual

25 November 2024
Dometic

Dometic DPS 80 Manual

25 November 2024
Kramer

Kramer 102MX Manual

25 November 2024
Kramer

Kramer FC-18 Manual

25 November 2024
Kramer

Kramer DSP-62-UC Manual

25 November 2024
Tiger

Tiger SKF-H101 Manual

25 November 2024