IFi Audio ZEN Blue Manual


Læs nedenfor 📖 manual på dansk for IFi Audio ZEN Blue (1 sider) i kategorien Hi-Fi system. Denne guide var nyttig for 7 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
4. Balanced 4.4mm outputs
For connection of 4.4mm > XLR or similarly balanced interconnects.
Warning: do NOT connect 4.4mm balanced headphones to the ZEN Blue as the full
signal is likely to damage your headphones and your hearing! iFi audio is not
responsible for any hearing or equipment damage arising from mis-use.
5. Single-Ended RCA outputs
Connect analogue RCA interconnects to an amplifier.
6. Digital/Analogue switch
Select between digital OR analogue signal output.
7. Digital outputs
To connect a coaxial or optical cable to a DAC.
8. Antenna
Please attach the enclosed antenna for maximum reception quality.
An optional +3dB antenna has been included for better performance.
9. DC 5V power
Connect the enclosed 5v power supply.
Tip: The ZEN Blue MUST be powered by 5 volts only. It is possible to
upgrade the enclosed 5v power supply by using a super low-noise supply
such as the iPower or iPower X.
Specifications:
Power Source:
Chipset:
Input:
Output:
Frequency Response:
Output Voltage @ 0dBFS:
Dynamic Range:
Signal/Noise ratio:
THD & N @ 0dBFS:
Output Impedance:
Power Consumption:
Dimensions:
Net weight:
Warranty period:
Specifications are subject to change without notice.
kHz
1 2 3
4 5 6 7 8 9
Thank you for purchasing the B from the Z series. Thelue EN
B is a wireless Bluetooth DAC with digital and analogue lue
outputs.
1. Bluetooth pairing button
The ZEN Blue receives a Bluetooth signal via apt , aptX ,X HD
aptX Adaptive, aptX LL, LDAC, HWA, AAC and SBC.
2. Bluetooth codec display
Codec
The colour of the iFi logo in the centre of the front display
represents the file format received:
Format LED
SB OffC
AAC Yellow
apt X Blue
aptX HD Magenta
aptX Adaptive Green
aptX RedLL
LDAC Cyan
LHD C/HWA White
3. Bluetooth pairing display
Pairing
From switch on, the ZEN Blue will blink blue as it searches for a
previously paired device. If a stored device is not found, it will
automatically enter pairing mode and blink blue/red.
To enter pairing mode, press and hold the front leftmost button
until the Bluetooth mode LED is blinking blue/red. To pair, on
your handset, look for ‘iFi Hi-Res audio’ in the list of available
Bluetooth devices.
The ZEN Blue is able to store up to 8 paired Bluetooth devices.
kHz LED
44/48 Blue
88/96 hite W Ver1.1
ifi-audio.com
BAL ANCED
COAXI AL DC 5V
LR OPT ICAL
Out puts
ANALOG DIGITAL
DC 5V
Qualcomm QCC 5100 Series
Bluetooth 5.0 with ,
TM AAC SBC, aptX,
aptX aptX Adaptive aptX HD, , LL, LDAC,
HWA Codec
Optical Coaxial, / Audio RCA L/R,
4 4 Balanced Lineout. 
20Hz - 20kHz +0/-0.5dB (44.1kHz)
1Hz - 44khz +0/-3.0dB (>= 88.2kHz)
2.05V (+/-0.05V)
109dB (A)
109dB (A) @ 0dBFS
<0.0015% 10k Load
<50Ω
<2.5W
1 x 100 x mm58 35
6.2" x 3.9" x 1.4"
476 1.05g ( lbs)
12 months
V2
Blue


Produkt Specifikationer

Mærke: IFi Audio
Kategori: Hi-Fi system
Model: ZEN Blue

Har du brug for hjælp?

Hvis du har brug for hjælp til IFi Audio ZEN Blue stil et spørgsmål nedenfor, og andre brugere vil svare dig




Hi-Fi system IFi Audio Manualer

Hi-Fi system Manualer

Nyeste Hi-Fi system Manualer