Ilsco ELT-4 Manual


Læs nedenfor 📖 manual på dansk for Ilsco ELT-4 (35 sider) i kategorien Kompressor. Denne guide var nyttig for 44 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/35
Connector Installation Guide
Compression and Mechanical
Connectors
Typical Cross Section of a
Compression Connector Before
Installation
Before compression, a
typical cross section of
cable consists of 75%
metal and 25% air
Typical Cross Section of a
Compression Connector After
Installation
After compression, little air is left.
H-Taps
C-Taps Narrow Tongue
Single & Dual
Mounting holes
Grid Grounding
Splices
Compression
Connector Types
Flared-End
1. Determine Proper Connector For Cable
Conductor size and CU = Copper conductors only
size and “AL9” = Aluminum conductors onlyConductor
size and “AL9CU” = Aluminum or Copper Conductor
conductors
Match size and type of conductor to proper lug
Note: Consult manufacturers instructions on whether ne stranded conductors
or welding cable conductor types may be used.
Manufacturer
Wire Size
Wire material- CU, AL, or AL9CU (indicates
Dual Rating and 90° C)
Optional Crimp Indicator Bands
Listing Information
Marking Information Connectors: on
2. Strip and Properly Prepare Cable
Strip insulation carefully to avoid nicking strands.
Strip to proper length so conductor can be fully inserted.
manufacturers Refer to instructions for strip length.
Most connectors are suitable for one conductor. Never
install more than one conductor unless specically
allowed by the manufacturer’s instructions.
Aluminum Conductor
Brush the stripped portion of the conductor to
remove oxide lm using a stainless steel wire brush.
Apply oxide inhibitor compound and wire brush into
the stranding. Do not remove pre-lled inhibitor from
the barrel.
Installation Guide for
Compression
4. Locate tool with correct die in proper position on connector
and activate tool
Connectors that are banded with colored stripes to indicate
number and location of each crimp.
Connectors may also be marked with the die code number at
each compression location.
Follow manufacturers instructions whether to crimp on the
colored bands or between the colored bands.
1st Crimps
2nd Crimps
4. Continued….
When crimped, the die code number or other marking will be
embossed on connector for easy inspection to determine if
correct die and connector combination were used.
Select proper installing dieless tool
as directed by the manufacturers instructions.Crimp
Dieless Tools
Use a 2-hole connector if there is a
concern for twisting the connection.
5. Connector Securement
Installation Guide
for Mechanical
Overhead
Transformer
Single
Conductor
Lug
Stud Type Transformer
Double
Conductor
Lug
Double
Conductor
Lug, NEMA
Pad
Copper
Single
Conductor
Lug
Mechanical
Connector Types


Produkt Specifikationer

Mærke: Ilsco
Kategori: Kompressor
Model: ELT-4

Har du brug for hjælp?

Hvis du har brug for hjælp til Ilsco ELT-4 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Kompressor Ilsco Manualer

Ilsco

Ilsco ELT-4 Manual

23 August 2024
Ilsco

Ilsco ELT-3 Manual

23 August 2024
Ilsco

Ilsco ELT-5 Manual

23 August 2024

Kompressor Manualer

Nyeste Kompressor Manualer

Cartrend

Cartrend 50241 Manual

21 Januar 2025
Hyundai

Hyundai HY2150100 Manual

20 Januar 2025
Hyundai

Hyundai HYSC100300 Manual

20 Januar 2025
POWERNAIL

POWERNAIL 445FS Manual

12 Januar 2025
Nilfisk

Nilfisk VHC200 Manual

11 Januar 2025
Fuxtec

Fuxtec FX-E1CI20 Manual

10 Januar 2025
Livoo

Livoo TEA306 Manual

30 December 2025