Indesit IWE 71082 S C ECO Manual

Indesit Vaskemaskine IWE 71082 S C ECO

Læs nedenfor 📖 manual på dansk for Indesit IWE 71082 S C ECO (60 sider) i kategorien Vaskemaskine. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/60

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 4

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 5

General safety

Disposal

Description of the washing machine, 6-7

Control panel

Display

Running a wash cycle, 8

Wash cycles and options, 9

Table of wash cycles

Wash options

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Load balancing system

Troubleshooting, 11

Service, 12

IWE 71082 S

Instructions for use

WASHING MACHINE

English,1

Türkçe,37

Русский,49

CSI

Polski,13

Українська,25

Installation

! This instruction manual should be kept in a safe

place for future reference. If the washing machi-

ne is sold, transferred or moved, make sure that

the instruction manual remains with the machine

so that the new owner is able to familiarise him-

self/herself with its operation and features.

! Read these instructions carefully: they con-

tain vital information relating to the safe instal-

lation and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its

packaging.

2. Make sure that the washing machine has

not been damaged during the transportation

process. If it has been damaged, contact the

retailer and do not proceed any further with

the installation process.

3. Remove the 4 pro-

tective screws (used

during transportation)

and the rubber wa-

sher with the cor-

responding spacer,

located on the rear

part of the appliance

( ).see figure

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will

need them again if the washing machine ne-

eds to be moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washing machine on a flat sturdy

floor, without resting it up against walls, furni-

ture cabinets or anything else.

2. If the floor is not

perfectly level, com-

pensate for any une-

venness by tightening

or loosening the

adjustable front feet

( ); the angle see figure

of inclination, measu-

red in relation to the

worktop, must not

exceed 2°.

Levelling the machine correctly will provide

it with stability, help to avoid vibrations and

excessive noise and prevent it from shifting

while it is operating. If it is placed on carpet or

a rug, adjust the feet in such a way as to allow

a sufficient ventilation space underneath the

washing machine.

Connecting the electricity and

water supplies

Connecting the water inlet hose

1. Connect the sup-

ply pipe by screwing

it to a cold water tab

using a ¾ gas threa-

ded connection (see

figure).

Before performing the

connection, allow the

water to run freely un-

til it is perfectly clear.

2. Connect the inlet

hose to the washing

machine by screwing

it onto the correspon-

ding water inlet of the

appliance, which is

situated on the top

right-hand side of the

rear part of the ap-

pliance . (see figure)

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical details

table (see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Technical data

Model IWE 71082 S

Dimensions

width 59.5 cm

height 85 cm

depth 53,5 cm

Capacity from 1 to 7 kg

Electrical

connections

please refer to the technical

data plate fixed to the machine

Water

connection

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed up to 1000 rotations per

minute

Test wash

cycles in

accordan-

ce with

directives

1061/2010

and

1015/2010

Programme 2:

Cotton standard 60°C.

Programme 3:

Cotton standard 40°C.

This appliance conforms to

the following EC Directives:

- 2004/108/EC dated

03/05/89 (Electromagnetic

Compatibility)

- 2012/19/EU

- 2006/95/EC Low Voltage)

65 - 100 cm

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drainage duct

or a wall drain located

at a height between

65 and 100 cm from

the floor;

alternatively, rest it on

the side of a washba-

sin or bathtub, faste-

ning the duct sup-

plied to the tap (see

figure). The free end

of the hose should

not be underwater.

! We advise against the use of hose exten-

sions; if it is absolutely necessary, the exten-

sion must have the same diameter as the

original hose and must not exceed 150 cm in

length.

Electrical connections

Before plugging the appliance into the electri-

city socket, make sure that:

• the socket is earthed and complies with all

applicable laws;

• the socket is able to withstand the maximum

power load of the appliance as indicated in

the Technical data table (see opposite);

• the power supply voltage falls within the

values indicated in the Technical data table

(see opposite);

• the socket is compatible with the plug of

the washing machine. If this is not the case,

replace the socket or the plug.

! The washing machine must not be installed

outdoors, even in covered areas. It is extreme-

ly dangerous to leave the appliance exposed

to rain, storms and other weather conditions.

! When the washing machine has been instal-

led, the electricity socket must be within easy

reach.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be repla-

ced by authorised technicians.

Warning! The company shall not be held

responsible in the event that these regulations

are not respected.

The first wash cycle

Once the appliance has been installed, and

before you use it for the first time, run a wash

cycle with detergent and no laundry, using the

wash cycle .2

Care and maintenance

Cutting off the water and electri-

city supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system

inside the washing machine and help to pre-

vent leaks.

• Unplug the washing machine when cleaning

it and during all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth

soaked in lukewarm soapy water. Do not use

solvents or abrasives.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pul-

ling it out ( ).see figure

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of

your appliance

• Always leave the porthole door ajar in order

to prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cle-

aning pump which does not require any main-

tenance. Sometimes, small items (such as

coins or buttons) may fall into the pre-chamber

which protects the pump, situated in its bot-

tom part.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. using a screwdri-

ver, remove the cover

panel on the lower

front part of the wa-

shing machine (see

figure ;)

2. unscrew the lid

by rotating it anti-

clockwise ( see figu-

re : ) a little water may

trickle out. This is

perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Precautions and tips

! This washing machine was designed and constructed in

accordance with international safety regulations. The fol-

lowing information is provided for safety reasons and must

therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children aged

from 8 years and above and persons with re-

duced physical, sensory or mental capabilities

or lack of experience and knowledge if they

have been given supervision or instruction

concerning use of the appliance in a safe way

and understand the hazards involved. Chil-

dren shall not play with the appliance. Clea-

ning and user maintenance shall not be made

by children without supervision.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach extreme-

ly high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

• If the appliance breaks down, do not under any circum-

stances access the internal mechanisms in an attempt

to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2012/19/EU on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected separately

in order to optimise the recovery and recycling of the

materials they contain and reduce the impact on human

health and the environment. The crossed out “wheeled

bin” symbol on the product reminds you of your obliga-

tion, that when you dispose of the appliance it must be

separately collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button : press this briefly to switch the ma-

chine on or off. The START/PAUSE indicator light, which

flashes slowly in a green colour shows that the machine is

switched on. To switch off the washing machine during the

wash cycle, press and hold the button for approximately 2

seconds; if the button is pressed briefly or accidentally the

machine will not switch off. If the machine is switched off

during a wash cycle, this wash cycle will be cancelled.

WASH CYCLE :knob used to set the desired wash cycle

(see “Table of wash cycles”).

OPTION : buttons with indicator light used to select the

available options. The indicator light corresponding to the

selected option will remain lit.

SPIN button : press to reduce or completely exclude

the spin cycle - the value is indicated on the display.

TEMPERATURE button : press to decrease or comple-

tely exclude the temperature: the value will be shown on

the display.

DELAYED START button : press to set a delayed start

time for the selected wash cycle. The delay time will be

shown on the display.

START/PAUSE button with indicator light: when the

green indicator light flashes slowly, press the button to

start a wash cycle. Once the cycle has begun the indicator

light will remain lit in a fixed manner. To pause the wash

cycle, press the button again; the indicator light will flash

in an orange colour. If the symbol is not illuminated, the

door may be opened (wait approximately 3 minutes). To

start the wash cycle from the point at which it was inter-

rupted, press the button again.

Standby mode

This washing machine, in compliance with new energy sa-

ving regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF button briefly and wait for the

machine to start up again.

Description of the washing

machine

Control panel

TEMPERATURE

Button

Detergent dispenser drawer

OPTION

buttons with

indicator lights

ON/OFF

button

SPIN SPEED

Button

START/PAUSE

button with indicator light

DISPLAY

DELAYED

START Button

WASH CYCLE

knob

Display

The display is useful when programming the machine and provides a great deal of information.

The duration of the available programmes and the remaining time of a running cycle appear in section ; if the DELAY START A

option has been set, the countdown to the start of the selected programme will appear. Pressing the relative button, the

machine automatically displays the maximum temperature and spin speed values set for the selected cycle, or the most

recently-used settings if they are compatible with the selected cycle.

The “programme phases” relative to the selected programme and the “programme phase” of the running programme appear

in section :B

Wash

Rinse

Spin

Drain

The icons corresponding to “temperature” , “Programmed start” and “spin” appear in section from top to bottom:C

If the symbol lights up, the display will visualise the set “temperature” value.

When a “delayed start” has been set, the symbol lights up.

If the symbol lights up, the display will visualise the set “spin” value.

Door locked symbol

The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the

door (wait approximately 3 minutes).

To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched

off the door may be opened (wait approximately 3 minutes).

Running a wash cycle

1. Press the button; SWITCH THE MACHINE ON.

the START/PAUSE indicator light will flash slowly in a

green colour.

2. Open the porthole door. LOAD THE LAUNDRY.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes on the following page.

3. Pull out the MEASURE OUT THE DETERGENT.

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in “Detergents

and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Set the WASH CYCLE

knob to the desired programme; a temperature and spin

speed is set for each wash cycle; these may be adjusted.

The duration of the cycle will appear on the display.

6. Use the relevant CUSTOMISE THE WASH CYCLE.

buttons:

Modifying the temperature and/or spin

speed. The machine automatically displays the

maximum temperature and spin speed values set for

the selected cycle, or the most recently-used settings

if they are compatible with the selected cycle. The

temperature can be decreased by pressing the

button, until the cold wash “OFF” setting is reached.

The spin speed may be progressively reduced by

pressing the button, until it is completely excluded

(the “OFF” setting). If these buttons are pressed again,

the maximum values are restored.

! Exception: if the programme is selected, the 2

temperature can be increased up to a value of 90°C.

Setting a delayed start.

To set a delayed start for the selected programme,

press the corresponding button repeatedly until the

required delay period has been reached. When this

option is enabled, the symbol lights up on the

display. To remove the delayed start option press the

button until the text “OFF” appears on the display.

Modifying the cycle settings.

• Press the button to enable the option; the indicator

light corresponding to the button will switch on.

• Press the button again to disable the option; the

indicator light will switch off.

! If the selected option is not compatible with the

programmed wash cycle, the indicator light will flash

and the option will not be activated.

! If the selected option is not compatible with another

option which has been selected previously, the indicator

light corresponding to the first option selected will flash

and only the second option will be activated; the indicator

light corresponding to the enabled option will remain lit.

! The options may affect the recommended load value

and/or the duration of the cycle.

7. Press the START/START THE PROGRAMME.

PAUSE button. The corresponding indicator light will

become green, remaining lit in a fixed manner, and the

door will be locked (the DOOR LOCKED symbol will

be on). To change a wash cycle while it is in progress,

pause the washing machine using the START/PAUSE

button (the START/PAUSE indicator light will flash

slowly in an orange colour); then select the desired

cycle and press the START/PAUSE button again.

To open the door while a cycle is in progress, press

the START/PAUSE button; if the DOOR LOCKED

symbol is switched off the door may be opened (wait

approximately 3 minutes). Press the START/PAUSE

button again to restart the wash cycle from the point at

which it was interrupted.

8. This will be THE END OF THE WASH CYCLE.

indicated by the text “ ” on the display; when the END

DOOR LOCKED symbol switches off the door may be

opened (wait approximately 3 minutes). Open the door,

unload the laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the button. The cycle will be stopped

and the machine will switch off.

Wash cycles and options

Wash options

Selecting this option enables you to suitably adjust drum

rotation, temperature and water to a reduced load of lightly

soiled cotton and synthetic fabrics (refer to the “Programme

table”). “ ” enables you to wash in less time thereby

saving water and electricity. We suggest using a liquid

detergent suitably measured out to the load quantity.

! It cannot be used with the 1, 6, 7, 8, 9, 10, 11, 12, 13,

14, , programmes.

The function saves energy by not heating the

water used to wash your laundry - an advantage both to

the environment and to your energy bill. Instead, intensified

wash action and water optimisation ensure great wash

results in the same average time of a standard cycle.

For the best washing results we recommend the usage of

a liquid detergent.

! It cannot be used with the 1, 6, 7, 8, 9, 10, 12, 13, 14,

, programmes.

Table of wash cycles

Extra Rinse

By selecting this option, the efficiency of the rinse is

increased and optimal detergent removal is guaranteed. It

is particularly useful for sensitive skin.

! It cannot be used in conjunction with the 8,

programmes.

Easy Iron

By selecting this function, the wash and spin cycles will be

modified in order to reduce the formation of creases. At the

end of the cycle the washing machine will perform slow ro-

tations of the drum; the indicator lights for the EASY IRON

and START/PAUSE options will flash (the first one green,

the second orange). To end the cycle, press the START/

PAUSE button or the EASY IRON button. For the 9 wash

cycle, the machine will end the cycle while the laundry is

soaking and the EASY IRON and START/PAUSE indicator

lights will flash. To drain the water so that the laundry may

be removed, press the START/PAUSE button or the EASY

IRON button.

! It cannot be used in conjunction with the 8, 10, 12, 13,

14, , programmes.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as

water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 2 with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments

which can be washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 3 with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments

which can be washed at 40°C. The actual washing temperature may differ from the indicated value.

For all Test Institutes:

2) Long wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.

3) Synthetic program along: set wash cycle 4 with a temperature of 40°C.

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergents

Max.

load (kg)

Residual

dampness

Energy

consum-

ption kWh

Total water lt

Cycle

duration

Pre-

wash Wash Fabric

softener

Daily

1 Cotton + Prewash: extremely soiled whites. 90° 1000    7 62 2,21 78 170’

2 Cotton Standard 60° (1): heavily soiled whites and resistant colours. 60°

(Max. 90°) 1000 -   7 62 1,10 52,5 190’

3 Cotton Standard 40° (2): lightly soiled whites and delicate colours. 40° 1000 -   7 62 0,99 82 185’

4 Synthetics: heavily soiled resistant colours. 60° 800 -   3 44 0,93 47 110’

4 Synthetics (3): lightly soiled resistant colours. 40° 800 -   3 44 0,57 46 95’

5 Mix Colored: lightly soiled whites and delicate colours. 40° 1000 -   7 62 0,66 54 90’

20° Zone

6Cotton Standard 20°: lightly soiled whites and delicate colours.

20°

1000 -

 

7 - - - 170’

7 Mix Light

20° 800

 

7 - - - 120’

8 20’ Refresh

20° 800

 

1,5 - - - 20’

Special

9 Silk/Curtains: for garments in silk and viscose, lingerie.

30° 0

 

1 - - - 55’

10 Wool: for wool, cashmere, etc.

40° 800

 

1,5 - - - 70’

11 Jeans

40° 800

 

3 - - - 70’

Sport

12 Sport Intensive 30° 600 -   2,5 - - - 85’

13 Sport Light 30° 600 -   2,5 - - - 60’

14 Special Shoes 30° 600 -   Max. 2

pairs - - - 60’

Partial wash cycles

Rinse - 1000 - - 7 - - - 36’

Spin + Drain - 1000 - - - 7 - - - 16’

Produkt Specifikationer

Mærke:	Indesit
Kategori:	Vaskemaskine
Model:	IWE 71082 S C ECO

Har du brug for hjælp?

Hvis du har brug for hjælp til Indesit IWE 71082 S C ECO stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vaskemaskine Indesit Manualer

Indesit W 144 XS Manual

15 Januar 2025

Indesit WN860WSK Manual

15 Januar 2025

Indesit lna 1000 Manual

15 Januar 2025

Indesit wia 600 Manual

15 Januar 2025

Indesit wite 127 Manual

14 Januar 2025

Indesit XWD 61452 Manual

13 Januar 2025

Indesit IM 712B MY TIME UA Manual

13 Januar 2025

Indesit IM 602B MY TIME UA Manual

13 Januar 2025

Indesit IM 600 MY TIME UA Manual

12 Januar 2025

Indesit IM 762 MY TIME EE Manual

9 Januar 2025

Vaskemaskine Manualer

Nyeste Vaskemaskine Manualer

Vedette VLT1155W Manual

22 Marts 2025

Vedette VLT612E2 Manual

22 Marts 2025

Vedette VLT6112at Manual

22 Marts 2025

Vedette LTV6011 Manual

22 Marts 2025

Vedette VED6012EL Manual

22 Marts 2025

Vedette VT16022Q Manual

22 Marts 2025

Vedette VT16024Q Manual

22 Marts 2025

Vedette TVC651 Manual

22 Marts 2025

Vedette VT6522Q Manual

22 Marts 2025

Vedette VT602BQ Manual

22 Marts 2025