InSinkErator Evolution 100 Manual

InSinkErator Ikke kategoriseret Evolution 100

Læs nedenfor 📖 manual på dansk for InSinkErator Evolution 100 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

English only (Australia, New Zealand, UK, Hong Kong, and Ireland)

www.insinkerator.com

Food waste disposers provide an environmentally responsible alternative to transporting food waste to landﬁlls. And they ca n help reduce

greenhouse gas emissions. At capable wastewater treatment plants, food waste can be converted to biosolids and used as fertilizer. Capable

plants can also capture methane gas and recycle it as an energy source. (Check the plant in your area.)

Read throu gh the entire Installation, Care & Use manual before installing the disposer. Determine which of the tools, materials, and

accessories you will need before you begin. Make sure you have all necessary disposer parts before installing the disposer.

NOTE: The Evolution models grind much ﬁner than any other disposer. For this reason you may notice that it takes a little longer to grind

some food waste. Due to the Evolu tion 200 model’s microprocessor, users will experience a fractional second delay when starting on all

Evolution 200 models. This is completely normal.

NOTE: must In Australia, all plumbing and electrical work be completed by a qualiﬁed tradesperson. This product may require approval of the

relevant regulator and/or the sewerage system operator. Disposer must be installed to AS/NZS 3500.2 standard requirements.

NOTE: Make sure that the installation of this appliance is allowed by the authorities.

TOOLS & MATERIALS YOU WILL NEED:

Slotted Screwdriver, Adjustable Pliers, Safety Glasses

TOOLS, MATERIALS, AND ACCESSORIES YOU MAY NEED:

Phillips Screwdriver, Drain Auger, 9.5 mm Electrical Clamp, Wire Nuts (2), 38 mm Drain Trap, 33 mm Hole Drill, Hammer, Hacksaw, Water Hose

Clamp, Pipe Wrench, Copper Earth Wire, Dishwasher Drain Connection Kit, Electrical On/Off Switch, Drain Tube Extension

MOUNTING ASSEMBLY

1a. Stra iner Basket and Plug

(Evolution models)

1b. Stopper (Models 65, 55, 45, LC-50)

2. Sink Flange

3. Rubber Gaskets (2)

4. Fiber Gasket (optiona l)

5. Backup Ring

6. Mounting Ring

7. Screws (3)

8. Snap Ring

DISPOSER

9. Sound Bafﬂe (Evolution models,

Model 65)

10. Mounting Gasket/Splash Bafﬂe

11. Lugs

12. Lower Mounting Ring

13. Dishwasher Inlet

14. Discharge Outlet

15. Wrenchette

DISCHARGE ASSEMBLY #4

(Australia Model LC-50 connected to

Caroma Connector not supplied)

26. Bolt (1) 19 mm 1/4-20 UNC

27. Metal Flange (Use to connect

to proper Caroma Connector)

28. Metal Washers (2)

29. Nuts (2)

30. Rubber Gasket

DISCHARGE ASSEMBLY #5

(Australia Models 65, 55, 45; connected to

Caroma Connector not supplied)

26. Bolts (2) 19 mm 1/4-20 UNC

28. Metal Washers (2)

30. Rubber Gasket

DISCHARGE ASSEMBLY #1

(Evolution models)

16. Hose Clamp

17. Black Elbow Discharge Tube

(38 mm diameter/Evolution ﬂange)

18. Straight Discharge Tube 40.3 mm OD

(Australia installation only)

DISCHARGE ASSEMBLY #2

(Models 65, 55, 45)

19. Bolts (2) 13 mm 1/4-20 UNC

20. Rubber Gasket

21. Metal Flange

22. White Elbow Discharge Tube

(38 mm diameter/non-Evolution ﬂange)

DISCHARGE ASSEMBLY #3

(LC-50 for household installation)

23. Bolt (1) 19 mm 1/4-20 UNC

24. Rubber Gasket

25. Metal Flange

22. White Elbow Discharge Tube

(38 mm diameter/non-Evolution ﬂange)

230-240V, 50Hz

for Australia and New Zealand

220-240V, 50Hz

for UK/Hong Kong/Ireland

Part No. 75978 REV. A

FOOD WASTE DISPOSER INSTALLATION, CARE & USE MANUAL

PARTS LIST (May vary depending on model)

Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Warning indicates a potentially hazardous situ ation which, if not avoided, could result in death or serious injury.

Cau tion indicated a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

31.8 cm 16.8 cm 6.4 cm 18.5 cm 13.1 cm

31.8 cm 16.8 cm 6.4 cm 17.3 cm 13.1 cm

31.8 cm 16.8 cm 6.4 cm 15.9 cm 13.1 cm

36.9 cm 19.3 cm 6.4 cm 20.6 cm 14.9 cm

34.4 cm 18.5 cm 6.4 cm 23.4 cm 16.8 cm

31.2 cm 17.1 cm 6.4 cm 20.5 cm 16.8 cm

(Evolution) 200-1, -3

(Evolution) 100-1, -3

Model 65-1B, -3B

Model 55-1B,

-1B A/S, -3B, -3B A/S

Model 45-1B,

-1B A/S, -3B

LC50-12, -13

CHECK INSTALLATION DIMENSIONS

1. Disposer Height

2. Distance from bottom of sink bowl to centerline of discharge outlet.

(Add 12 mm when stainless steel sink is used.)

3. Distance from centerline of the discharge outlet to end of

discharge tube.

4. Disposer Width

5. Distance from disposer vertical centerline to centerline of

trap connection.

To properly drain and prevent standing water in the disposer, the waste

pipe entering the wall must be lower than the disposer discharge outlet.

DISCONNECT SINK DRAIN

1. Loosen nut (1) at top of trap (4) with pipe wrench (see Figure 4.1).

2. Loosen nut (2) at top of extension pipe. Remove extension pipe.

3. Loosen nut (3) at base of sink ﬂange.

4. Push sink ﬂange up through sink hole and remove it (see Figure 4. 2).

5. Clean sink ﬂange area of any putty or other debris.

The sink hole may have to be enlarged to accept the disposer NOTE:

sink ﬂange. Sink hole enla rgement tools are available from your

InSinkErator Dealer.

2.1

4.33.3

2.31.3

2.41.4

5.1

1. Turn mounting assembly over (see Figu re 2.1) and loosen three

mounting screws (1) until you can access snap ring (2).

2. Use screwdriver to pry snap ring off of sink ﬂange. Mounting

assembly will now come apart.

3. Set mounting assembly aside. This will be used in Instruction 5.

IF REPLACING AN EXISTING DISPOSER,

CONTINUE WITH INSTRUCTION 3.

IF THIS IS A FIRST TIME INSTALLATION,

SKIP AHEAD TO INSTRUCTION 4.

DISASSEMBLE NEW DISPOSER

MOUNTING ASSEMBLY Reference Figure 5.1.

1. Place one of two rubber gaskets (2) under sink ﬂange (1). Ensure sink

hole area is clear of debris and place sink ﬂange/gasket into sink hole.

You may wish to place a weighted object in the sink to hold the sink

ﬂange in place. (Place a towel under object to prevent scratching.)

2. Working from under the sink, slip second rubber gasket (2), ﬁber

gasket (optional) (3) a nd metal backup ring (4) (ﬂat side up) over the

sink ﬂange.

3. Holding second rubber gasket, ﬁber gasket (optiona l) and metal

backup ring in place, slip mounting ring (5) over sink ﬂange so it seats

against backup ring.

4. With the rubber gasket, ﬁber gasket (optional), backup ring, and

mounting ring tight against sink bottom, slide snap ring (7) onto sink

ﬂange until it pops into groove on ﬂange.

5. Tighten three mounting screws (6) up to sink until mounting assembly

is seated tightly and evenly against sink.

ATTACH UPPER MOUNTING ASSEMBLY TO SINK

REMOVE EXISTING DISPOSER

PERSONAL INJURY

To avoid personal injury, do not position your head or body under

disposer; the unit could fall during installation.

ELECTRICAL SHOCK

• To avoid electrical shock, disconnect power before installing or

servicing disposer. Turn off electrical power at fuse box or circuit

breaker or if equipped unplug disposer electrical power plu g from

wall outlet.

• Improper connection of equ ipment earth (grounded) conductor

can result in electric shock.

1. If your disposer is equipped with an electric plug and cord

connection, unplug power plug from electrical wall outlet.

If your disposer is not equipped with an electrical plug and

cord connection, contact an electrician to disconnect the old

disposer plus install an earth (grounded) electrical wall outlet for

the new disposer connection that must be compliant to all local

electrical codes.

2. Disconnect drain trap from disposer waste discharge tube with

adjustable pliers (see Figure 3.1). Also disconnect dishwasher drain

connection, if applica ble.

3. Support disposer with one hand and insert end of wrenchette or

screwdriver into right side of one mounting lug on lower mounting

ring (see Figure 3.2). Lift disposer slightly and remove from mounting

by pushing or pulling wrenchette or screwdriver to left (disposer may

be heavy; provide support).

4. Loosen three mounting screws, pry snap ring off with screwdriver,

and remove old mounting assembly (see Figure 3.3). Some mounting

assembly removal requires additional tools.

5. Push old sink ﬂa nge up through sink hole (see Figure 3.4). Skip ahead

to Instruction 5.

7.1

7.37.2

Failure to clean sink waste pipe line may result in waste pipe blockage.

1. Remove trap. (See Figure 6.1)

2. With drain auger, clear away all hardened waste material in horizontal drain line running from drain trap to main pipe.

IF YOU ARE NOT CONNECTING A DISHWASHER TO DISPOSER, SKIP AHEAD TO INSTRUCTION 8.

DOES NOT APPLY TO AUSTRALIA/NEW ZEALAND In Australia, it is

suggested that the dishwasher units be connected to IPLEX/ COROMA

dishwasher spigot for maximum efﬁciency.

Wastewater from a dishwasher can be plumbed into the disposer

through the inlet access on the upper part of the disposer. There is a

plug on the inside of the inlet tube on all models. Once removed, the

knockout plug cannot be replaced.

NOTE: If the dishwasher connection is made without removing the plug,

the dishwasher may overﬂow. (Connections must comply with local

plumbing codes.)

REMOVE KNOCKOUT PLUG

1. Lay disposer on its side and insert screwdriver into dishwasher inlet so

tip rests on outer edge of knockout plug.

2. Tap end of screwdriver handle with hammer until molded plug brea ks

loose (see Figure 7.1).

3. Remove loose knockout plug from inside disposer.

DISHWASHER ATTACHMENT AND OVERFLOW CONNECTION

CLEAN SINK WASTE PIPE

THE SINK OVERFLOW

The sink overﬂow may be connected to the overﬂow tube on the

tailpipe (see Figure 7.2). Remove the overﬂow connector cap and

blue plastic seal from the end of the overﬂow tu be (see Figure 7.3).

Utilizing the nut, connect the overﬂow hose to the tailpipe.

NOTE: The straight discharge tu be for use in Australia does not

have an overﬂow connection tube. In the UK, waste trap kit, which

does not include the sink overﬂow kit, is available from your local

InSinkErator dealer.

6.1

(installation continued on reverse)

InSinkErator Division

Suite 6, Building 6

Hatters Lane,

Croxley Green Business Park

Watford HERTS WD18 8YH

United Kingdom

Sales Tel: (0) 1 923 297 880

Service Tel: (0) 800 389 3715

www.insinkerator.co.uk

Parex Industries Ltd.

5 Tolich Place, Henderson

P.O. Box 21-102

Auckland, New Zealand 0610

Sales Tel: 64 9 836 6566

Service Tel: 0800 200 510

www.parex.co.nz

InSinkErator Division

471 Mountain Highway

Bayswater Vic 3153, Australia

Sales Tel: 61 03 9720 5599

Service Tel: 1 300 136 205

www.insinkerator.com.au

InSinkErator Division

Emerson Electric Co.

4700 21st Street

Racine, WI 53406-5093

USA

Sales/Service Tel:

262-554-3652

www.insinkerator.com/

worldmap.html

KAL Group

4078 Kingswood Road,

Citywest Business Park

Dublin, Ireland

Tel: 01 413 6481,

01 413 6400

Fax: 01 413 6464

Email: info@kal.ie

PERSONAL INJURY

Wearing safety glasses is recommended during the installation of

the food waste disposer.

Evolution 100: Australia Pat. No. 307603, 307769, 308385, and other foreign patents pending

Evolution 200: Australia Pat. No. 307601, 307769, 308695, 308385, and other foreign patents pending

Produkt Specifikationer

Mærke:	InSinkErator
Kategori:	Ikke kategoriseret
Model:	Evolution 100
Type:	Affaldskværn under vask
Vekselstrømsindgangsspænding:	110 - 240 V
Vekselstrømsindgangsfrekvens:	50 - 60 Hz
Bredde:	220 mm
Højde:	311 mm
Vægt:	10000 g
Produktfarve:	Grey, Stainless steel
Kontroltype:	Air switch, Wall switch
Strøm:	9.5 A
Rotationshastighed:	1725 rpm
Kapacitet:	1005 ml
Motorkraft:	0.75 hp
Afløb, størrelse:	1.5 "
Indføringstype:	Kontinuerlig indføring