Intermec ScanPlus 1800PDF Manual
Intermec
Stregkodelæser
ScanPlus 1800PDF
Læs nedenfor 📖 manual på dansk for Intermec ScanPlus 1800PDF (171 sider) i kategorien Stregkodelæser. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/171
Installation Manual
ScanPlus 1800
Hand-held Scanner
P/N 0-360049-02
Contents
ScanPlus 1800 - Installation Manual
3
Contents
1. Using EasySet .............................................................................................. 9
online setup with RS-232 cable 0-364032-00 ........................................ 10
2. Reset all parameters ................................................................................... 11
3. Terminal / cash register used in your application .......................................... 13
connections.......................................................................................... 14
keyboard wedge........................................................................ 14
RS-232 ..................................................................................... 15
laser emulation .......................................................................... 16
wand emulation ......................................................................... 17
IBM 46xx cash registers............................................................. 18
OCIA cash registers................................................................... 18
predefined terminal selections .............................................................. 19
keyboard wedge........................................................................ 19
RS-232 ..................................................................................... 21
laser emulation .......................................................................... 24
wand emulation ......................................................................... 24
IBM 46xx cash registers............................................................. 26
OCIA cash registers................................................................... 27
custom interface number ...................................................................... 28
4. Data transmission settings........................................................................... 29
keyboard wedge................................................................................... 30
preamble................................................................................... 30
symbology identifier ................................................................... 31
postamble ................................................................................. 36
special keys interpretation (Code 39) ......................................... 38
special keys transmission .......................................................... 41
inter-character delay .................................................................. 43
inter-message delay .................................................................. 44
Contents
4
ScanPlus 1800 - Installation Manual
end-of-transmission keyboard character status........................... 45
RS-232................................................................................................ 46
baud rate .................................................................................. 46
data bits.................................................................................... 47
parity ........................................................................................ 47
stop bits .................................................................................... 48
hardware/software protocols timeout.......................................... 48
ENQ ......................................................................................... 49
ACK.......................................................................................... 49
NAK.......................................................................................... 50
XON / XOFF software protocol................................................... 51
RTS / CTS hardware protocol.................................................... 52
preamble................................................................................... 53
preamble / postamble................................................................ 53
symbology identifier................................................................... 54
postamble................................................................................. 59
LRC (longitudinal redundancy check)......................................... 59
inter-character delay.................................................................. 60
inter-message delay .................................................................. 61
laser emulation .................................................................................... 63
transmitted symbology type ....................................................... 63
margin size ............................................................................... 63
logical signal state during transmission ...................................... 64
logical signal state outside transmission..................................... 64
inter-message delay .................................................................. 64
wand emulation.................................................................................... 66
transmitted symbology type ....................................................... 66
margin size ............................................................................... 66
logical signal state during transmission ...................................... 67
logical signal state outside transmission..................................... 67
pulse duration ........................................................................... 68
Contents
6
ScanPlus 1800 - Installation Manual
barcode length .........................................................................101
PDF417..............................................................................................102
macro PDF ..............................................................................102
Plessey Code......................................................................................107
check digit................................................................................107
barcode length .........................................................................108
Standard 2 of 5 ...................................................................................109
format ......................................................................................109
check digit mod 10 ...................................................................109
barcode length .........................................................................110
Telepen ..............................................................................................112
format ......................................................................................112
UPC / EAN .........................................................................................113
add-on digits ............................................................................114
check digit................................................................................115
UPC number system ................................................................116
re-encoding UPC-A, UPC-E, EAN-8..........................................117
6. Operating settings......................................................................................119
trigger activation .................................................................................120
trigger operating scenarios .......................................................121
standard mode .........................................................................123
standard mode with aiming beam..............................................124
energy saver mode...................................................................124
trigger read duration.................................................................125
flashing mode .....................................................................................126
autostand mode..................................................................................127
data decoding security ........................................................................129
predefined security levels .........................................................129
consecutive same read data validation......................................130
timeout between identical consecutive codes ............................130
timeout between different consecutive codes.............................131
Contents
ScanPlus 1800 - Installation Manual
7
beeps / green indicator LED ............................................................... 132
volume .................................................................................... 132
note (tone frequency)............................................................... 132
power-up beeps / power-up LED .............................................. 133
good read beeps...................................................................... 133
good read LED ........................................................................ 135
PDF417 codes......................................................................... 135
7. Configuration modes and utilities ............................................................... 137
temporary configuration mode............................................................. 140
A. ASCII character codes .............................................................................. 141
B. Additional preamble / postamble characters—Keyboard wedge.................. 157
C. Number codes .......................................................................................... 163
D. Test codes................................................................................................ 165
Index ............................................................................................................ 167
Contents
8
ScanPlus 1800 - Installation Manual
1. Using EasySet online setup with RS-232 cable 0-364032-00
10
ScanPlus 1800 - Installation Manual
online setup with RS-232 cable 0-364032-00
RS-232 direct cable 0-364032-00
- online setup with RS-232 cable 0-364032-00 :
1. connect the RS-232 cable to your product if it is not already connected
2. connect the RS-232 cable to the serial port of your PC
3. connect the power supply to the RS-232 cable and provide electrical power
4. select your Intermec product in EasySet ("Select reader" icon over the product image)
5. read the "start EasySet online setup" code (double-click to send it to the setup sheet and
print it out, or read it from the Getting Started Guide or Installation Manual)
6. open the "Configure communication PC/Reader" dialog box in the "Reader" menu
7. select the COM serial port your product is connected to (no parity, 8 data bits, 19200 bauds)
8. select the "Send to reader" checkbox under the commands window
9. double-click on the setup commands to send them directly to your product (they are also
sent to the setup sheet)
10. connect your normal product cable to your product (if applicable) when you have finished
online setup
2. Reset all parameters
ScanPlus 1800 - Installation Manual
11
2. Reset all parameters
- global reset of all parameter settings - useful for a first-time setup or for a fresh start with a new
application
- default settings are indicated by (*)
reset factory defaults
\46\42\60
- resets all configuration parameters to their default values and cancels
the terminal / cash register selection
- after a global reset, you must select the terminal / cash register used in
your application (>> next section) and customize your setup
parameters if required
2. Reset all parameters
12
ScanPlus 1800 - Installation Manual
3. Terminal / cash register used in your application
ScanPlus 1800 - Installation Manual
13
3. Terminal / cash register used in your
application
- terminal selection necessary for transmission to your terminal / cash register !!!
- look for your system configuration in the terminal selector (full list of all supported terminals) or
use the predefined terminal selections if applicable
- the number of green LED flashes at power-up indicates the cable / interface configuration of
your product
- green LED always on = no terminal / cash register selected
- energy saver trigger models : if the trigger is activated, you will have to press the trigger to see
the power-up flashes
terminal selector (all terminals):
this option only available
with EasySet
- database of all supported terminals (look for your system configuration
in the list)
3. Terminal / cash register used in your application connections
14
ScanPlus 1800 - Installation Manual
connections
keyboard wedge
( )
( )
DIN/mini-DIN adaptor cable
(standard wedge)
standard wedge cable 0-364037-00
DEC VT 220/320/420 cable 0-364037-02
Wyse cable 0-365036-00
"short" MicroBar cables
0-601xxx-xx
CMM-compatible wedge cable 0-364037-03
( )
3. Terminal / cash register used in your application connections
16
ScanPlus 1800 - Installation Manual
laser emulation
laser emulation cable 0-366030-00
3. Terminal / cash register used in your application connections
ScanPlus 1800 - Installation Manual
17
wand emulation
wand emulation cable 0-364031-00
(not energy saver)
wand emulation cable 0-366031-00
(Intermec Interface / energy saver)
3. Terminal / cash register used in your application connections
18
ScanPlus 1800 - Installation Manual
IBM 46xx cash registers
IBM 46xx 9x cable 0-365033-00
OCIA cash registers
OCIA NCR 7052/7053 cable 0-365035-00
3. Terminal / cash register used in your application predefined terminal selections
ScanPlus 1800 - Installation Manual
19
predefined terminal selections
- look in the terminal selector if you cannot find your system configuration in this section
keyboard wedge
- "keyboard wedge" = connection between a keyboard and the host system (data is transmitted in
keyboard emulation mode)
- switch off the host system before you connect the cables and optional power supply !
- 7 green LED flashes at power-up
standard PC
- look in the terminal selector if you cannot find your system configuration in this section
QWERTY English
\41\4A\03\08\60
AZERTY French
\41\4A\03\09\60
QWERTZ German
\41\4A\03\0C\60
QWERTY Swedish / Finnish
\41\4A\03\0D\60
QWERTY Italian
\41\4A\03\0E\60
3. Terminal / cash register used in your application predefined terminal selections
20
ScanPlus 1800 - Installation Manual
QWERTY Norwegian
\41\4A\03\0F\60
QWERTY Danish
\41\4A\03\10\60
QWERTY Spanish
\41\4A\03\11\60
QWERTZ Swiss / French
\41\4A\1F\24\60
DEC VT 220, 320, 420
- look in the terminal selector if you cannot find your system configuration in this section
QWERTY PC type
\41\4A\06\1A\60
AZERTY PC type
\41\4A\06\1B\60
QWERTZ PC type
\41\4A\06\1E\60
QWERTY PC type Swedish / Finnish
\41\4A\06\1F\60
3. Terminal / cash register used in your application predefined terminal selections
ScanPlus 1800 - Installation Manual
21
RS-232
- switch off the host system before you connect the cables and power supply !
- 2 green LED flashes at power-up
standard RS-232 C (9600, 7, E, 2)
\41\4A\01\24\60
- predefined terminal selection also available with the terminal selector
- PC serial port compatible
- customize individual RS-232 settings to suit your system after reading
this parameter
special RS-232 configurations
TTL logical 0 = 0V (9600, 7, E, 2)
\41\4A\01\24\60
- customize individual RS-232 settings to suit
your system after reading this parameter
TTL logical 0 = 5V (9600, 7, E, 2)
\41\4A\01\24\40\50\60
- customize individual RS-232 settings to suit your
system after reading this parameter
PC Term (19200, 8, none, 2)
\41\4A\01\26\60
3. Terminal / cash register used in your application predefined terminal selections
22
ScanPlus 1800 - Installation Manual
slave mode (9600, 7, E, 2)
\41\4A\01\29\60
- for RS-232 C and RS-232 TTL with logical 0 = 0V
- allows the ScanPlus 1800 to be configured or controlled directly by the host system via
the RS-232 serial port
- optimized high-security Code 128 transmission (start/stop, hexadecimal characters,
checksum)
1. use "display data string mode" (see section 7 "Configuration modes and utilities") to
display on a terminal screen the data string and checksum for the setup commands you
want to send to the ScanPlus 1800 in slave mode (the EasySet "View - Data String"
command displays the command data strings but does not display the checksum !)
Example: "Code 39 - active" = \ 41 \ 4C \ 60 \ 5E ("5E" = checksum)
Calculating the checksum
1. Calculate the weighted sum of the data string values (weight increases by 1 for each
successive value) and include startB with weight 1 at the beginning :
data string : startB 0x41 0x4C 0x60
weight : 1 1 2 3
weight * value : (1 * 0x68) + (1 * 0x41) + (2 * 0x4C) + (3 * 0x60) = 0x261
2. Calculate the modulo 103 value (modulo 67 hex) of the sum:
0x261 modulo 0x67 = 0x5E (= checksum)
(0x261 / 0x67 = 0x5 with remainder 0x5E)
3. Add the checksum to the data string
Example: "Code 39 - active" = \41\4C\60\5E
2. remove the backslash separator characters from the data strings and adapt each string
to slave mode format :
<start> <command> <checksum> <stop>
< 6 8 > x x x x x x x x < 6 A >
Example: slave mode command = 68 41 4C 60 5E 6A
3. Terminal / cash register used in your application predefined terminal selections
ScanPlus 1800 - Installation Manual
23
3. activate "slave mode" and reconfigure the standard RS-232 output parameters to suit
your system if required
- the ScanPlus 1800 goes into "temporary configuration mode" (see section 7
"Configuration modes and utilities")
4. send the commands from the host terminal to the ScanPlus 1800 (individually or as a list
in a batch file)
- the values displayed in "display data string mode" are hexadecimal values, make sure
that the values you send from the host system correspond to these values - in our
example, the ScanPlus 1800 must receive the hexadecimal value 41 or its equivalent
(ASCII character "A" for example), not the decimal value "41" !
5. send "update current configuration" (0x68 0x46 0x41 0x02 0x60 0x4C 0x6A) if you want
to save the new configuration you have sent to the ScanPlus 1800 (see section 7
"Configuration modes and utilities")
simplified slave mode (9600, 7, E, 2)
\41\4A\01\2D\60
- for RS-232 C and RS-232 TTL with logical 0 = 0V
- allows the ScanPlus 1800 to be configured or controlled directly by the host system via
the RS-232 serial port
- easy-to-monitor character string (same as the strings displayed with the EasySet "View -
Data String" command) but less secure than standard "slave mode" (no start/stop or
checksum)
1. use the EasySet "View - Data String" command to obtain the data strings for the
commands you want to send to the ScanPlus 1800
Example: command for "Code 39 - active" = \ 4 1 \ 4 C \ 6 0
- if you use "display data string mode" (see section 7 "Configuration modes and utilities"),
do not use the last 2 digits (checksum)
2. activate "simplified slave mode" and reconfigure the standard RS-232 output parameters
to suit your system if required
- the ScanPlus 1800 goes into "temporary configuration mode" (see section 7
"Configuration modes and utilities")
3. send the commands in ASCII format from the host terminal to the ScanPlus 1800
(individually or as a list in a batch file)
3. Terminal / cash register used in your application predefined terminal selections
24
ScanPlus 1800 - Installation Manual
4. send "update current configuration" ( \ 4 6 \ 4 1 \ 0 2 \ 6 0 ) if you want to save the new
configuration you have sent to the ScanPlus 1800 (see section 7 "Configuration modes
and utilities")
laser emulation
- switch off the host system before you connect the cable !
- no LED flash at power-up
- activates "energy saver mode - active for read duration (2 s), standby after good read" (see
section 6, "Operating settings - trigger activation")
laser with trigger
\41\4A\02\04\60
- predefined terminal selection also available with the terminal selector
wand emulation
- predefined terminal selections also available with the terminal selector
- switch off the host system before you connect the cable !
- 1 green LED flash at power-up
- connecting a wand cable activates general wand interface default settings (see section 4, "Data
transmission settings") if a specific wand interface is not already selected
analog wand emulation (white high)
\41\4A\02\03\60
- bar = 0, space = 1, margin = 1, quiet zone = 1
- good read beeps after transmission, pulse
duration = 1.32 ms, intermessage delay = 750
ms
3. Terminal / cash register used in your application predefined terminal selections
ScanPlus 1800 - Installation Manual
25
analog wand emulation (Intermec Interface, white high)
\41\4A\02\07\60
- bar = 0, space = 1, margin = 1, quiet zone = 1
- energy saver mode, active while trigger pressed,
standby after good read (see section 6,
"Operating settings - trigger activation")
- beeps not active, good read LED before
transmission, pulse duration = 0.15 ms, no
intermessage delay
- for Intermec products such as 97XX wedge
products, JANUS 2010 hand-held computers,
TRAKKER Antares 242X terminals, use :
ScanPlus 1800 product P/N
ScanPlus 1800 SR + wand emulation cable 0 - 3 6 0 0 5 1 - 0 1
ScanPlus 1800 ST + wand emulation cable 0 - 3 6 6 0 5 1 - 0 1
wand emulation cable 0 - 3 6 6 0 3 1 - 0 0
digital wand emulation (black high)
\41\4A\02\02\60
- bar = 1, space = 0, margin = 0, quiet zone = 0
- good read beeps after transmission, pulse
duration = 0.85 ms, intermessage delay = 750
ms
3. Terminal / cash register used in your application predefined terminal selections
26
ScanPlus 1800 - Installation Manual
IBM 46xx cash registers
- predefined terminal selections also available with the terminal selector
- switch off the host system before you connect the cable !
- 3 green LED flashes at power-up
- setup is independent of the physical link with the cash register (you can configure for Port 9x or
Port 5x as required by the host)
Port 9x
\41\4A\01\2E\60
- you cannot send this parameter online to the
ScanPlus 1800 through RS-232 cable 0-
364032-00 !!! (send it to the setup sheet and
read the configuration code with your normal
IBM product cable connected)
Port 5x
\41\4A\01\2F\60
- you cannot send this parameter online to the
ScanPlus 1800 through RS-232 cable 0-364032-
00 !!! (send it to the setup sheet and read the
configuration code with your normal IBM product
cable connected)
3. Terminal / cash register used in your application predefined terminal selections
ScanPlus 1800 - Installation Manual
27
OCIA cash registers
- look in the terminal selector if you cannot find your system configuration in this section
- switch off the host system before you connect the cable !
- 5 green LED flashes at power-up
- if you have problems with your OCIA configuration, switch off the system to reset the cash
register and your product and try another OCIA type
TEC 1st type
\41\4A\01\38\60
- you cannot send this parameter online to the
ScanPlus 1800 through RS-232 cable 0-
364032-00 !!! (send it to the setup sheet and
read the configuration code with your normal
OCIA product cable connected)
TEC 2nd type
\41\4A\01\39\60
- you cannot send this parameter online to the
ScanPlus 1800 through RS-232 cable 0-364032-
00 !!! (send it to the setup sheet and read the
configuration code with your normal OCIA
product cable connected)
NCR
\41\4A\01\3A\60
- you cannot send this parameter online to the
ScanPlus 1800 through RS-232 cable 0-
364032-00 !!! (send it to the setup sheet and
read the configuration code with your normal
OCIA product cable connected)
3. Terminal / cash register used in your application custom interface number
28
ScanPlus 1800 - Installation Manual
custom interface number
compose: [range: 100-30000]
\41\4A\60
- enter a number string and scan End Selection (Appendix C)
- for special host system configurations
4. Data transmission settings
ScanPlus 1800 - Installation Manual
29
4. Data transmission settings
- interface-specific communication parameters
- modify data transmission settings to optimize performance
4. Data transmission settings keyboard wedge
30
ScanPlus 1800 - Installation Manual
keyboard wedge
- default values (*) are for IBM PC AT and compatible - QWERTY English
preamble
[preamble] [symbology id] <data> [postamble]
none (*)
\45\53\3E\00\60
compose:
\45\53\60
- enter an ASCII / Special Wedge Characters string
and scan End Selection (Appendix A and B)
- maximum = 20 characters
4. Data transmission settings keyboard wedge
ScanPlus 1800 - Installation Manual
31
symbology identifier
[preamble] [symbology id] <data> [postamble]
AIM
[preamble] [symbology id] <data> [postamble]
- optional 3-character symbology identifiers standardized by the AIM Committee
Example: " ] A 0 " identifies standard Code 39 without check digit
- refer to the official AIM documentation on symbology identifiers for full information on the
different processing options supported
symbology ] <symbology_id> <processing_option>
Codabar ] F 0, 2, 4
Code 39 ] A 0, 1, 2, 4
Code 93 ] G 0
Code 128/EAN 128 ] C 0, 1
Interleaved 2 of 5 ] I 0, 1, 2
Matrix 2 of 5 ] X 0
Standard 2 of 5 ] S 0, 1, 2
MSI Code ] M 0, 1
PDF417 ] L 0
Plessey Code ] P 0
Telepen ] B 0, 1
UPC/EAN (1) ] E 0, 3, 4
UPC/EAN (2) ] X 0
(1) UPC/EAN "standard" lengths = 8, 13, 15 (add-on 2), 18 (add-on 5) characters
(2) UPC/EAN other lengths (no check digit, . . .)
not transmitted (*)
\47\59\60
4. Data transmission settings keyboard wedge
32
ScanPlus 1800 - Installation Manual
transmitted
\47\58\60
- activates AIM symbology identifier transmission
for all symbologies
custom
[preamble] [symbology id] <data> [postamble]
not transmitted (*)
\45\56\60
transmitted
\45\55\60
- activates custom symbology identifier
transmission for all symbologies
compose
- compose 1 custom character
Codabar: [range: 1]
\45\59\04\60
- enter an ASCII character and scan End
Selection (Appendix A)
- default = D
4. Data transmission settings keyboard wedge
ScanPlus 1800 - Installation Manual
33
Code 39: [range: 1]
\45\59\01\60
- enter an ASCII character and scan End Selection
(Appendix A)
- default = *
Code 93: [range: 1]
\45\59\0D\60
- enter an ASCII character and scan End
Selection (Appendix A)
- default = D
Code 128 / EAN 128: [range: 1]
\45\59\0B\60
- enter an ASCII character and scan End Selection
(Appendix A)
- default = D
EAN-8: [range: 1]
\45\59\07\60
- enter an ASCII character and scan End
Selection (Appendix A)
- default = FF
EAN-13: [range: 1]
\45\59\06\60
- enter an ASCII character and scan End Selection
(Appendix A)
- default = F
4. Data transmission settings keyboard wedge
34
ScanPlus 1800 - Installation Manual
Interleaved 2 of 5: [range: 1]
\45\59\02\60
- enter an ASCII character and scan End
Selection (Appendix A)
- default = I
Matrix 2 of 5: [range: 1]
\45\59\0E\60
- enter an ASCII character and scan End Selection
(Appendix A)
- default = D
MSI Code: [range: 1]
\45\59\0A\60
- enter an ASCII character and scan End
Selection (Appendix A)
- default = D
PDF417: [range: 1]
\45\59\13\60
- enter an ASCII character and scan End Selection
(Appendix A)
- default = *
Plessey Code: [range: 1]
\45\59\0C\60
- enter an ASCII character and scan End
Selection (Appendix A)
- default = D
4. Data transmission settings keyboard wedge
ScanPlus 1800 - Installation Manual
35
Standard 2 of 5: [range: 1]
\45\59\03\60
- enter an ASCII character and scan End Selection
(Appendix A)
- default = D
Telepen: [range: 1]
\45\59\0F\60
- enter an ASCII string and scan End Selection
(Appendix A)
- default = *
UPC-A: [range: 1]
\45\59\08\60
- enter an ASCII character and scan End Selection
(Appendix A)
- default = A
UPC-E: [range: 1]
\45\59\09\60
- enter an ASCII character and scan End
Selection (Appendix A)
- default = E
4. Data transmission settings keyboard wedge
36
ScanPlus 1800 - Installation Manual
postamble
[preamble] [symbology id] <data> [postamble]
none
\45\54\3E\00\60
Enter (*)
\45\54\04\02\01\60
Carriage Return
\45\54\04\02\02\60
Tab
\45\54\04\02\08\60
Field Advance
\45\54\04\02\04\60
Field Exit
\45\54\04\02\05\60
Down Arrow
\45\54\04\02\0F\60
4. Data transmission settings keyboard wedge
ScanPlus 1800 - Installation Manual
37
compose:
\45\54\60
- enter an ASCII / Special Wedge Characters string
and scan End Selection (Appendix A and B)
- maximum = 20 characters
4. Data transmission settings keyboard wedge
38
ScanPlus 1800 - Installation Manual
special keys interpretation (Code 39)
- certain dual-character combinations in Code 39 bar codes can be interpreted and transmitted as
special keyboard keys (Code 39 is not full ASCII and does not support direct encoding of
special keyboard keys such as <Enter> and <Tab>)
- only for keyboard wedge applications with Code 39 bar codes !!! (your product must be enabled
to read Code 39 codes with the correct barcode length settings)
emulated key characters emulated key characters
DEL .A PF1 0A
ENTER .B PF2 0B
RETURN .C PF3 0C
SEND .D PF4 0D
FIELD + .E PF5 0E
FIELD EXIT .F PF6 0F
HOME .G PF7 0G
END .H PF8 0H
TAB .I PF9 0I
ALT .J PF10 0J
BACK TAB .K PF11 0K
BACKSPACE .L PF12 0L
right arrow .M PF13 0M
left arrow .N PF14 0N
up arrow .O PF15 0O
down arrow .P PF16 0P
CLEAR .Q PF17 0Q
FIELD - .R PF18 0R
DUP .S PF19 0S
ESC .T PF20 0T
LINE FEED .U PF21 0U
RESET .V PF22 0V
CTRL .W PF23 0W
SPECIAL .X PF24 0X
4. Data transmission settings keyboard wedge
ScanPlus 1800 - Installation Manual
39
not active (*)
\42\57\60
- special dual-character combinations not
interpreted (original code string transmitted
without interpretation)
Example ( . I dual-character combination = <Tab> )
original Code 39 code: interpreted and transmitted as:
msg . Ixx msg . Ixx
. I . I
x - . I x - . I
msg - . Ixx msg - . Ixx
always active
\42\58\60
- special dual-character combinations always
interpreted as special keys
Example ( . I dual-character combination = <Tab> )
original Code 39 code: interpreted and transmitted as:
msg . Ixx msg<Tab>xx
. I <Tab>
x - . I x <Tab>
msg - . Ixx msg<Tab>xx
4. Data transmission settings keyboard wedge
40
ScanPlus 1800 - Installation Manual
separate 2 character label
\42\5A\60
- special dual-character combinations interpreted
if only 2 characters in the original code
Example ( . I dual-character combination = <Tab> )
original Code 39 code: interpreted and transmitted as:
msg . Ixx msg . Ixx
. I <Tab>
x - . I x - . I
msg - . Ixx msg - . Ixx
separate 2 character label or preceded by a hyphen
\42\59\60
- special dual-character combinations interpreted
if only 2 characters in the original code or if
there is a hyphen in front of the 2 characters
Example ( . I dual-character combination = <Tab> )
original Code 39 code: interpreted and transmitted as:
msg . Ixx msg . Ixx
. I <Tab>
x - . I x <Tab>
msg - . Ixx msg<Tab>xx
4. Data transmission settings keyboard wedge
ScanPlus 1800 - Installation Manual
41
special keys transmission
- only symbologies that support the full ASCII character set allow the encoding of special
keyboard keys such as <Return> and <Tab>
- no symbologies support the encoding of other function keys such as <PF1> and <PageDown>
- the special keys transmission codes allow you to transmit special keyboard keys as a single
keyboard character, a [<Ctrl> + character] combination, or an [<Alt> + decimal_sequence]
combination
control character conversion
- emulates PC AT keyboard [<Ctrl> + character] sequence or transmits certain keyboard
functions directly as single keyboard characters
on (*)
\47\4D\60
- transmits the following characters directly as
single keyboard characters:
ASCII character: transmitted as:
8 <Backspace> (not <Ctrl> H )
9 <Tab> (not <Ctrl> I )
10 (not transmitted)
13 <Enter> (not <Ctrl> M )
27 <Escape> (not <Ctrl> [ )
- useful to avoid confusion for applications that
already use control sequences as commands
4. Data transmission settings keyboard wedge
42
ScanPlus 1800 - Installation Manual
off
\47\4E\60
- transmits ASCII characters for decimal numbers
1 to 27 with the corresponding [<Ctrl> +
character] sequence
Alt mode
- emulates PC AT keyboard [<Alt> + decimal_sequence] function (for bar codes containing ASCII
characters not on your keyboard)
off (*)
\41\47\60
on
\41\46\60
- use only if necessary as transmission is slower !!!
(all characters are transmitted as <Alt>
sequences)
Example
"A { B" is transmitted as:
<Alt> + <6> + <5> <Alt> + <1> + <2> + <3> <Alt> + <6> + <6>
4. Data transmission settings keyboard wedge
ScanPlus 1800 - Installation Manual
43
inter-character delay
- avoids dropping characters if transmitting decoded data too fast for the host system
- do not use for IBM 46xx cash registers or laser/wand emulation !!!
none (*)
\52\00\60
10 ms
\52\0A\60
20 ms
\52\14\60
30 ms
\52\1E\60
40 ms
\52\28\60
50 ms
\52\32\60
compose (ms): [range: 1-999 ms]
\52\60
- enter a number string and scan End Selection
(Appendix C)
4. Data transmission settings keyboard wedge
44
ScanPlus 1800 - Installation Manual
inter-message delay
- avoids dropping characters if transmitting decoded data too fast for the host system
none (*)
\53\00\60
10 ms
\53\0A\60
30 ms
\53\1E\60
50 ms
\53\32\60
80 ms
\53\01\10\60
100 ms
\53\01\24\60
compose (ms): [range: 1-999 ms]
\53\60
- enter a number string and scan End Selection
(Appendix C)
4. Data transmission settings keyboard wedge
ScanPlus 1800 - Installation Manual
45
end-of-transmission keyboard character status
- sets keyboard to lower case or upper case at end of transmission
- Code 39 is transmitted in upper case
- Code 128 is transmitted in lower case / upper case (full ASCII)
lower case (*)
\41\44\60
upper case
\41\45\60
4. Data transmission settings RS-232
46
ScanPlus 1800 - Installation Manual
RS-232
- default values (*) are for standard RS-232 C (9600, 7, E, 2)
baud rate
75
\41\00\60
150
\41\01\60
300
\41\02\60
600
\41\03\60
1200
\41\04\60
2400
\41\05\60
4800
\41\06\60
4. Data transmission settings RS-232
ScanPlus 1800 - Installation Manual
47
9600 (*)
\41\07\60
19200
\41\08\60
38400
\41\09\60
data bits
7 (*)
\42\60
8
\43\60
parity
even (*)
\46\01\60
odd
\46\02\60
none
\46\00\60
4. Data transmission settings RS-232
48
ScanPlus 1800 - Installation Manual
stop bits
1
\44\60
2 (*)
\45\60
hardware/software protocols timeout
- the same timeout applies to all RS-232 protocols supported
1000 ms (*)
\51\0F\28\60
unlimited
\51\00\60
compose (ms): [range: 0-2500 ms]
\51\60
- enter a number string and scan End Selection
(Appendix C)
4. Data transmission settings RS-232
ScanPlus 1800 - Installation Manual
49
ENQ
- ENQ not used: barcode data is transmitted without receiving a request from the host system
- ENQ used: data is transmitted if ENQ character received from host system before end of
hardware/software protocols time-out
not used (*)
\47\3E\00\60
used (ENQ 05h)
\47\3E\05\60
compose:
\47\60
- enter an ASCII character and scan End
Selection (Appendix A)
ACK
- activating ACK or NAK activates the ACK/NAK protocol
- before reading a new bar code after transmission, the product waits for an ACK (positive
acknowledge) from the host system or until the end of the hardware/software protocols time-out
not used (*)
\48\3E\00\60
used (ACK 06h)
\48\3E\06\60
4. Data transmission settings RS-232
50
ScanPlus 1800 - Installation Manual
compose:
\48\60
- enter an ASCII character and scan End
Selection (Appendix A)
NAK
- activating ACK or NAK activates the ACK/NAK protocol
- a NAK (negative acknowledge) indicates an unsuccessful transmission attempt
- after 3 unsuccessful transmission attempts, message is aborted
not used (*)
\49\3E\00\60
used (NAK 15h)
\49\3E\15\60
compose:
\49\60
- enter an ASCII character and scan End
Selection (Appendix A)
4. Data transmission settings RS-232
ScanPlus 1800 - Installation Manual
51
Typical ENQ / ACK / NAK scenarios
ScanPlushost terminal
ACK
(clears message)
message
(OK)
ENQ
ScanPlushost terminal
message
(not OK)
NAK
ENQ
ACK
(clears message)
repeats message
(OK)
XON / XOFF software protocol
- the host system controls the flow of data from the reader
- XOFF (ASCII character DC3) from the host at the end of the hardware/software protocols time-
out interrupts transmission
- XON (ASCII character DC1) restarts the data flow
not active (*)
\4B\60
4. Data transmission settings RS-232
52
ScanPlus 1800 - Installation Manual
active
\4A\60
RTS / CTS hardware protocol
- CTS is tested before transmission of each character - data is only transmitted when CTS is
activated
- RTS is activated before data is transmitted
- RTS can be deactivated after transmission of each character, after transmission of the whole
message, or after an RTS pulse which can be emitted when each character is transmitted
not active (*)
\47\5F\00\60
active, RTS idle after each character
\47\5F\01\60
active, RTS idle after whole message
\47\5F\03\60
active, RTS pulse on each character
\47\5F\02\60
4. Data transmission settings RS-232
ScanPlus 1800 - Installation Manual
53
compose delay before RTS idle (ms): [range: 0-2500 ms]
\47\5E\60
- enter a number string and scan End Selection
(Appendix C)
- default = 10 ms
- delay for RTS idle after each character / idle
after whole message
- not valid for RTS pulse on each character
preamble
[preamble] [symbology id] <data> [postamble]
none (*)
\45\53\3E\00\60
compose:
\45\53\60
- enter an ASCII string and scan End Selection
(Appendix A)
- maximum = 20 characters
preamble / postamble
[preamble] [symbology id] <data> [postamble]
STX / ETX
\45\53\3E\02\45\54\3E\03\60
4. Data transmission settings RS-232
54
ScanPlus 1800 - Installation Manual
symbology identifier
[preamble] [symbology id] <data> [postamble]
AIM
[preamble] [symbology id] <data> [postamble]
- optional 3-character symbology identifiers standardized by the AIM Committee
Example: " ] A 0 " identifies standard Code 39 without check digit
- refer to the official AIM documentation on symbology identifiers for full information on the
different processing options supported
symbology ] <symbology_id> <processing_option>
Codabar ] F 0, 2, 4
Code 39 ] A 0, 1, 2, 4
Code 93 ] G 0
Code 128/EAN 128 ] C 0, 1
Interleaved 2 of 5 ] I 0, 1, 2
Matrix 2 of 5 ] X 0
Standard 2 of 5 ] S 0, 1, 2
MSI Code ] M 0, 1
PDF417 ] L 0
Plessey Code ] P 0
Telepen ] B 0, 1
UPC/EAN (1) ] E 0, 3, 4
UPC/EAN (2) ] X 0
(1) UPC/EAN "standard" lengths = 8, 13, 15 (add-on 2), 18 (add-on 5) characters
(2) UPC/EAN other lengths (no check digit, . . .)
not transmitted (*)
\47\59\60
4. Data transmission settings RS-232
ScanPlus 1800 - Installation Manual
55
transmitted
\47\58\60
- activates AIM symbology identifier transmission
for all symbologies
custom
[preamble] [symbology id] <data> [postamble]
not transmitted (*)
\45\56\60
transmitted
\45\55\60
- activates custom symbology identifier
transmission for all symbologies
compose
- compose 1 custom character
Codabar: [range: 1]
\45\59\04\60
- enter an ASCII character and scan End
Selection (Appendix A)
- default = D
4. Data transmission settings RS-232
56
ScanPlus 1800 - Installation Manual
Code 39: [range: 1]
\45\59\01\60
- enter an ASCII character and scan End Selection
(Appendix A)
- default = *
Code 93: [range: 1]
\45\59\0D\60
- enter an ASCII character and scan End
Selection (Appendix A)
- default = D
Code 128 / EAN 128: [range: 1]
\45\59\0B\60
- enter an ASCII character and scan End Selection
(Appendix A)
- default = D
EAN-8: [range: 1]
\45\59\07\60
- enter an ASCII character and scan End
Selection (Appendix A)
- default = FF
EAN-13: [range: 1]
\45\59\06\60
- enter an ASCII character and scan End Selection
(Appendix A)
- default = F
4. Data transmission settings RS-232
ScanPlus 1800 - Installation Manual
57
Interleaved 2 of 5: [range: 1]
\45\59\02\60
- enter an ASCII character and scan End
Selection (Appendix A)
- default = I
Matrix 2 of 5: [range: 1]
\45\59\0E\60
- enter an ASCII character and scan End Selection
(Appendix A)
- default = D
MSI Code: [range: 1]
\45\59\0A\60
- enter an ASCII character and scan End
Selection (Appendix A)
- default = D
PDF417: [range: 1]
\45\59\13\60
- enter an ASCII character and scan End Selection
(Appendix A)
- default = *
Plessey Code: [range: 1]
\45\59\0C\60
- enter an ASCII character and scan End
Selection (Appendix A)
- default = D
4. Data transmission settings RS-232
ScanPlus 1800 - Installation Manual
59
postamble
[preamble] [symbology id] <data> [postamble]
none
\45\54\3E\00\60
Carriage Return + Line Feed (*)
\45\54\3E\0D\3E\0A\60
Carriage Return
\45\54\3E\0D\60
Line Feed
\45\54\3E\0A\60
compose:
\45\54\60
- enter an ASCII string and scan End Selection
(Appendix A)
- maximum = 20 characters
LRC (longitudinal redundancy check)
not active (*)
\4F\60
4. Data transmission settings RS-232
60
ScanPlus 1800 - Installation Manual
active
\4E\60
inter-character delay
- avoids dropping characters if transmitting decoded data too fast for the host system
- do not use for IBM 46xx cash registers or laser/wand emulation !!!
none (*)
\52\00\60
10 ms
\52\0A\60
20 ms
\52\14\60
30 ms
\52\1E\60
40 ms
\52\28\60
50 ms
\52\32\60
4. Data transmission settings RS-232
ScanPlus 1800 - Installation Manual
61
compose (ms): [range: 1-999 ms]
\52\60
- enter a number string and scan End Selection
(Appendix C)
inter-message delay
- avoids dropping characters if transmitting decoded data too fast for the host system
none (*)
\53\00\60
10 ms
\53\0A\60
30 ms
\53\1E\60
50 ms
\53\32\60
80 ms
\53\01\10\60
100 ms
\53\01\24\60
4. Data transmission settings RS-232
62
ScanPlus 1800 - Installation Manual
compose (ms): [range: 1-999 ms]
\53\60
- enter a number string and scan End Selection
(Appendix C)
4. Data transmission settings laser emulation
ScanPlus 1800 - Installation Manual
63
laser emulation
- default values (*) are for standard laser with trigger
- transmitted symbology type :
- PDF417, Telepen : data is transmitted in Code 128 format
- all other symbologies : data can be transmitted in original barcode format or in Code 39
format
transmitted symbology type
- transmits data in original barcode format or in Code 39 format
transmission in original code format (*)
\5E\00\60
transmission in Code 39
\5E\01\60
- original code must not contain characters not
supported by Code 39
margin size
- defined in increments of narrow bar width (50 µs)
10 x narrow bar width (*)
\5A\0A\60
4. Data transmission settings laser emulation
64
ScanPlus 1800 - Installation Manual
compose (x narrow bar width):
\5A\60
- enter a number string and scan End Selection
(Appendix C)
logical signal state during transmission
bar = 1, space = 0, margin = 0 (*)
\54\60
bar = 0, space = 1, margin = 1
\55\60
logical signal state outside transmission
quiet zone = 1 (*)
\57\60
quiet zone = 0
\56\60
inter-message delay
- avoids dropping characters if transmitting decoded data too fast for the host system
none (*)
\53\00\60
4. Data transmission settings laser emulation
ScanPlus 1800 - Installation Manual
65
10 ms
\53\0A\60
30 ms
\53\1E\60
50 ms
\53\32\60
80 ms
\53\01\10\60
100 ms
\53\01\24\60
compose (ms): [range: 1-999 ms]
\53\60
- enter a number string and scan End Selection
(Appendix C)
4. Data transmission settings wand emulation
66
ScanPlus 1800 - Installation Manual
wand emulation
- default values (*) are for analog wand emulation
- transmitted symbology type :
- PDF417, Telepen : data is transmitted in Code 128 format
- all other symbologies : data can be transmitted in original barcode format or in Code 39
format
transmitted symbology type
- transmits data in original barcode format or in Code 39 format
transmission in original code format (*)
\5E\00\60
transmission in Code 39
\5E\01\60
- original code must not contain characters not
supported by Code 39
margin size
- defined in increments of narrow bar width (50 µs)
10 x narrow bar width (*)
\5A\0A\60
4. Data transmission settings wand emulation
ScanPlus 1800 - Installation Manual
67
compose (x narrow bar width):
\5A\60
- enter a number string and scan End Selection
(Appendix C)
logical signal state during transmission
bar = 0, space = 1, margin = 1 (*)
\55\60
bar = 1, space = 0, margin = 0
\54\60
logical signal state outside transmission
quiet zone = 1 (*)
\57\60
quiet zone = 0
\56\60
4. Data transmission settings wand emulation
68
ScanPlus 1800 - Installation Manual
pulse duration
- times in ms represent the pulse duration of a narrow bar or space
- speeds in parentheses are for standard UPC/EAN bar codes with 0.33 mm narrow-bar elements
- emulated pulse duration speed = [ 100 x ( r / t ) ] cm/s, where r = actual narrowest element
(mm) and t = setup duration element (ms)
Example
if r = 0.45 mm and t = 0.4 ms, emulated speed = 100 x (0.45 / 0.4) = 112.5 cm/s
0.15 ms (220 cm/s EAN 100%) (*)
\58\0F\60
0.19 ms (175 cm/s EAN 100%)
\58\13\60
0.26 ms (125 cm/s EAN 100%)
\58\1A\60
0.44 ms (75 cm/s EAN 100%)
\58\2C\60
0.66 ms (50 cm/s EAN 100%)
\58\01\02\60
0.88 ms (37.5 cm/s EAN 100%)
\58\01\18\60
1.32 ms (25 cm/s EAN 100%)
\58\02\04\60
4. Data transmission settings wand emulation
ScanPlus 1800 - Installation Manual
69
2.64 ms (12.5 cm/s EAN 100%)
\58\04\08\60
6.60 ms (5 cm/s EAN 100%)
\58\0A\14\60
compose (x 10 µs):
\58\60
- enter a number string and scan End Selection
(Appendix C)
inter-message delay
- avoids dropping characters if transmitting decoded data too fast for the host system
none (*)
\53\00\60
10 ms
\53\0A\60
30 ms
\53\1E\60
50 ms
\53\32\60
4. Data transmission settings wand emulation
70
ScanPlus 1800 - Installation Manual
80 ms
\53\01\10\60
100 ms
\53\01\24\60
compose (ms): [range: 1-999 ms]
\53\60
- enter a number string and scan End Selection
(Appendix C)
4. Data transmission settings IBM 46xx cash registers
ScanPlus 1800 - Installation Manual
71
IBM 46xx cash registers
inter-message delay
- avoids dropping characters if transmitting decoded data too fast for the host system
- do not send this parameter online to the ScanPlus 1800 through RS-232 cable 0-364032-00 !!!
(send it to the setup sheet and read the configuration code with your normal IBM product cable
connected)
none (*)
\53\00\60
10 ms
\53\0A\60
30 ms
\53\1E\60
50 ms
\53\32\60
80 ms
\53\01\10\60
100 ms
\53\01\24\60
4. Data transmission settings OCIA cash registers
ScanPlus 1800 - Installation Manual
73
OCIA cash registers
inter-character delay
- avoids dropping characters if transmitting decoded data too fast for the host system
- do not use for IBM 46xx cash registers or laser/wand emulation !!!
- do not send this parameter online to the ScanPlus 1800 through RS-232 cable 0-364032-00 !!!
(send it to the setup sheet and read the configuration code with your normal OCIA product cable
connected)
none (*)
\52\00\60
10 ms
\52\0A\60
20 ms
\52\14\60
30 ms
\52\1E\60
40 ms
\52\28\60
50 ms
\52\32\60
4. Data transmission settings OCIA cash registers
74
ScanPlus 1800 - Installation Manual
compose (ms): [range: 1-999 ms]
\52\60
- enter a number string and scan End Selection
(Appendix C)
inter-message delay
- avoids dropping characters if transmitting decoded data too fast for the host system
- do not send this parameter online to the ScanPlus 1800 through RS-232 cable 0-364032-00 !!!
(send it to the setup sheet and read the configuration code with your normal OCIA product cable
connected)
none (*)
\53\00\60
10 ms
\53\0A\60
30 ms
\53\1E\60
50 ms
\53\32\60
80 ms
\53\01\10\60
100 ms
\53\01\24\60
4. Data transmission settings OCIA cash registers
ScanPlus 1800 - Installation Manual
75
compose (ms): [range: 1-999 ms]
\53\60
- enter a number string and scan End Selection
(Appendix C)
4. Data transmission settings OCIA cash registers
76
ScanPlus 1800 - Installation Manual
5. Symbologies
ScanPlus 1800 - Installation Manual
77
5. Symbologies
- symbology = bar code type or family (e.g. Code 39, UPC, EAN)
- activate the symbologies you need and modify the settings for your symbologies if required
- to optimize performance, only activate symbologies you need !!! (deactivate the Code 39 and
UPC/EAN default symbologies if you don't need them)
disable all symbologies
\41\4B\60
- deactivates all the symbologies activated
- use the "not active" options to deactivate individual symbologies
- does not reset individual parameter settings for each symbology (when
you reactivate a symbology, you recover the parameter settings stored
in memory for that symbology when it was disabled - use reset factory
defaults to reset all the symbology parameters to their factory default
settings)
5. Symbologies Codabar
78
ScanPlus 1800 - Installation Manual
Codabar
- numerical symbology
not active (*)
\41\53\60
active
\41\52\60
start/stop
not transmitted (*)
\43\4D\60
a, b, c, d
\43\4E\60
A, B, C, D
\43\4F\60
a, b, c, d / t, n, *, e
\43\50\60
DC1, DC2, DC3, DC4
\43\51\60
5. Symbologies Codabar
ScanPlus 1800 - Installation Manual
79
CLSI library system
- spaces inserted after characters 1, 5, 10 in the 14-character label (used in the USA by libraries
using the CLSI system)
Example: "39990000192148" is transmitted as "3 9990 00019 2148"
- start/stop can be transmitted or not transmitted as required
not active (*)
\43\53\60
active (insert spaces)
\43\52\60
check digit (AIM recommendation)
- AIM has a recommended check character for Codabar
- each Codabar data character (including Start/Stop) has a value assigned to it:
0 = 0 1 = 1 2 = 2 3 = 3 4 = 4 5 = 5 6 = 6 7 = 7 8 = 8 9 = 9 - = 10 $ = 11 : =
12 / = 13 , = 14 + = 15 A = 16 B = 17 C = 18 D = 19
- the values are added and the check is calculated: check = [(next multiple of 16) - (sum of
assigned AIM values)]
Example
data characters: A 0 1 2 3 4 B
AIM values = 16 + 0 + 1 + 2 + 3 + 4 + 17: 43
next multiple of 16: 48
check = 48 - 43: 5
final message: A 0 1 2 3 4 5 B
5. Symbologies Codabar
80
ScanPlus 1800 - Installation Manual
not used (*)
\46\56\60
checked and transmitted
\46\54\60
checked but not transmitted
\46\55\60
barcode length
= <start> + <barcode data> + [check digit] + <stop>
- minimum length possible = 3 characters
- if the codes in your application have fixed lengths, use the "compose 1 or 2 or 3 fixed lengths"
option !!!
compose 1 or 2 or 3 fixed lengths:
\43\54\60
- enter a number string and scan End Selection
for each length and scan End Selection twice to
finish (Appendix C)
- compose 1 or 2 or 3 fixed lengths provides the
best performance and security if the codes in
your application have fixed lengths
- minimum length possible = 3 characters
any length
\43\55\00\60
- cancels any fixed length / minimum length
settings and accepts any valid length (3 or more
characters)
5. Symbologies Codabar
ScanPlus 1800 - Installation Manual
81
compose minimum length: [range: 3-50]
\43\55\60
- enter a number string and scan End Selection
(Appendix C)
- compose a minimum length if the codes in your
application do not have 1 or 2 or 3 fixed lengths
- to optimize decoding performance and increase
security, select the same length as the
minimum length in your application (do not
select a shorter length !!)
minimum length = 6 (*)
\43\55\06\60
5. Symbologies Code 39
82
ScanPlus 1800 - Installation Manual
Code 39
- alphanumeric symbology
- letter case not defined - transmitted in upper case
- default format = Standard 43 Characters
active (*)
\41\4C\60
not active
\41\4D\60
format
standard 43 characters (*)
\42\4A\60
full ASCII
\42\4B\60
- extra characters encoded using 1 of 4 control
characters ($, %, /, +) combined with a letter:
5. Symbologies Code 39
ScanPlus 1800 - Installation Manual
83
Code 39 ASCII Hex Dec
%U NUL 00 0
$A SOH 01 1
$B STX 02 2
$C ETX 03 3
$D EOT 04 4
$E ENQ 05 5
$F ACK 06 6
$G BEL 07 7
$H BS 08 8
$I HT 09 9
$J LF 0A 10
$K VT 0B 11
$L FF 0C 12
$M CR 0D 13
$N SO 0E 14
$O SI 0F 15
$P DLE 10 16
$Q DC1 11 17
$R DC2 12 18
$S DC3 13 19
$T DC4 14 20
$U NAK 15 21
$V SYN 16 22
$W ETB 17 23
$X CAN 18 24
$Y EM 19 25
$Z SUB 1A 26
%A ESC 1B 27
%B FS 1C 28
%C GS 1D 29
%D RS 1E 30
%E US 1F 31
Space SP 20 32
/A ! 21 33
5. Symbologies Code 39
84
ScanPlus 1800 - Installation Manual
Code 39 ASCII Hex Dec
/B " 22 34
/C # 23 35
$ $ 24 36
% % 25 37
/F & 26 38
/G ' 27 39
/H ( 28 40
/I ) 29 41
/J * 2A 42
+ + 2B 43
/L , 2C 44
/M - 2D 45
/N . 2E 46
/ / 2F 47
0 0 30 48
1 1 31 49
2 2 32 50
3 3 33 51
4 4 34 52
5 5 35 53
6 6 36 54
7 7 37 55
8 8 38 56
9 9 39 57
/Z : 3A 58
%F ; 3B 59
%G < 3C 60
%H = 3D 61
%I > 3E 62
%J ? 3F 63
%V @ 40 64
A A 41 65
B B 42 66
C C 43 67
5. Symbologies Code 39
ScanPlus 1800 - Installation Manual
85
Code 39 ASCII Hex Dec
D D 44 68
E E 45 69
F F 46 70
G G 47 71
H H 48 72
I I 49 73
J J 4A 74
K K 4B 75
L L 4C 76
M M 4D 77
N N 4E 78
O O 4F 79
P P 50 80
Q Q 51 81
R R 52 82
S S 45 83
T T 54 84
U U 55 85
V V 56 86
W W 57 87
X X 58 88
Y Y 59 89
Z Z 5A 90
%K [ 5B 91
%L \ 5C 92
%M ] 5D 93
%N ^ 5E 94
%O _ 5F 95
%W ` 60 96
+A a 61 97
+B b 62 98
+C c 63 99
+D d 64 100
+E e 65 101
5. Symbologies Code 39
86
ScanPlus 1800 - Installation Manual
Code 39 ASCII Hex Dec
+F f 66 102
+G g 67 103
+H h 68 104
+I i 69 105
+J j 6A 106
+K k 6B 107
+L l 6C 108
+M m 6D 109
+N n 6E 110
+O o 6F 111
+P p 70 112
+Q q 71 113
+R r 72 114
+S s 73 115
+T t 74 116
+U u 75 117
+V v 76 118
+W w 77 119
+X x 78 120
+Y y 79 121
+Z z 7A 122
%P { 7B 123
%Q | 7C 124
%R } 7D 125
%S ~ 7E 126
%T DEL 7F 127
start/stop
not transmitted (*)
\42\4D\60
5. Symbologies Code 39
88
ScanPlus 1800 - Installation Manual
French CIP
- French pharmaceutical industry
- only used for codes with 7 characters
checked and transmitted
\42\52\60
checked but not transmitted
\42\53\60
Italian CPI
- Italian pharmaceutical industry
- transmitted as standard Code 39 if checksum not validated
checked and transmitted
\42\54\60
checked but not transmitted
\42\55\60
5. Symbologies Code 39
ScanPlus 1800 - Installation Manual
89
barcode length
= <start> + <barcode data> + [check digit] + <stop>
- minimum length possible = 3 characters
- use the "compose minimum length" option if you know the minimum length of the codes in your
application !!!
any length (*)
\42\5C\00\60
- cancels the last minimum length selection and
accepts any valid length (3 or more characters)
compose minimum length: [range: 3-50]
\42\5C\60
- enter a number string and scan End Selection
(Appendix C)
- to optimize decoding performance and increase
security, select the same length as the minimum
length in your application (do not select a shorter
length !!)
minimum length = 6
\42\5C\06\60
5. Symbologies Code 93
90
ScanPlus 1800 - Installation Manual
Code 93
- alphanumeric full ASCII symbology - letter case defined
not active (*)
\41\5F\60
active
\41\5E\60
barcode length
= <barcode data>
- minimum length possible = 1 character
- use the "compose minimum length" option if you know the minimum length of the codes in your
application !!!
any length (*)
\45\42\00\60
- cancels the last minimum length selection and
accepts any valid length (1 or more characters)
compose minimum length: [range: 1-50]
\45\42\60
- enter a number string and scan End Selection
(Appendix C)
- to optimize decoding performance and increase
security, select the same length as the minimum
length in your application (do not select a shorter
length !!)
5. Symbologies Code 93
ScanPlus 1800 - Installation Manual
91
minimum length = 6
\45\42\06\60
5. Symbologies Code 128 / EAN 128
92
ScanPlus 1800 - Installation Manual
Code 128 / EAN 128
- alphanumeric full ASCII symbology - letter case defined
- "EAN 128" = Code 128 with the FNC1 character in the first position
- EAN 128 is auto-discriminating with Code 128 (recognition of the FNC1 start character used)
not active (*)
\41\5B\60
active
\41\5A\60
EAN 128 identifier
- the ]C1 AIM identifier for EAN 128 is automatically added by default in front of EAN 128 bar
codes
include ]C1 identifier (*)
\47\5A\01\60
remove ]C1 identifier
\47\5A\00\60
5. Symbologies Code 128 / EAN 128
ScanPlus 1800 - Installation Manual
93
CIP 128 French pharmaceutical codes
- embedded CIP 39 data
- fixed length 14 characters
- Code 128 character set C
not active (*)
\47\5D\00\60
active
\47\5D\01\60
FNC1 separator character (EAN 128 norms)
- default = GS function character (ASCII 29)
- used as separator when multiple identifiers and their fields are concatenated
- Example: useful for keyboard wedge interfaces where the GS character can not be transmitted
compose:
\46\52\60
- enter an ASCII character and scan End Selection (Appendix A)
5. Symbologies Code 128 / EAN 128
94
ScanPlus 1800 - Installation Manual
barcode length
= <barcode data>
- minimum length possible = 1 character
- use the "compose minimum length" option if you know the minimum length of the codes in your
application !!!
- Code 128 / EAN 128 does not use the same number of characters to code alphanumerical data
and numerical data - if you can not read bar codes in your application, this may be due to an
unsuitable minimum length - try entering a shorter length !
any length (*)
\44\55\00\60
- cancels the last minimum length selection and
accepts any valid length (1 or more characters)
compose minimum length: [range: 1-50]
\44\55\60
- enter a number string and scan End Selection
(Appendix C)
- to optimize decoding performance and increase
security, select the same length as the minimum
length in your application (do not select a shorter
length !!)
minimum length = 6
\44\55\06\60
5. Symbologies Interleaved 2 of 5
ScanPlus 1800 - Installation Manual
95
Interleaved 2 of 5
- numerical symbology
not active (*)
\41\4F\60
active
\41\4E\60
check digit
- especially recommended for variable length Interleaved 2 of 5 and if "consecutive same read
data validation" (data decoding security parameters) is not activated
not used (*)
\43\43\60
mod 10
checked and transmitted
\42\5F\60
checked but not transmitted
\43\40\60
5. Symbologies Interleaved 2 of 5
96
ScanPlus 1800 - Installation Manual
French CIP HR
- French pharmaceutical industry
- only used for codes with 7 characters
checked and transmitted
\43\41\60
checked but not transmitted
\43\42\60
barcode length
= <barcode data> + [check digit]
- minimum length possible = 2 characters
- if the codes in your application have fixed lengths, use the "compose 1 or 2 or 3 fixed lengths"
option !!!
- Interleaved 2 of 5 always encodes an even number of characters
- for codes with an odd number of characters, you can add a last character printed as 5 narrow
bars (not transmitted)
compose 1 or 2 or 3 fixed lengths:
\43\44\60
- enter a number string and scan End Selection
for each length and scan End Selection twice to
finish (Appendix C)
- compose 1 or 2 or 3 fixed lengths provides the
best performance and security if the codes in
your application have fixed lengths
- minimum length possible = 2 characters
5. Symbologies Interleaved 2 of 5
ScanPlus 1800 - Installation Manual
97
any length
\43\45\00\60
- cancels any fixed length / minimum length
settings and accepts any valid length (2 or more
characters)
compose minimum length: [range: 2-50]
\43\45\60
- enter a number string and scan End Selection
(Appendix C)
- compose a minimum length if the codes in your
application do not have 1 or 2 or 3 fixed lengths
- to optimize decoding performance and increase
security, select the same length as the
minimum length in your application (do not
select a shorter length !!)
minimum length = 6 (*)
\43\45\06\60
5. Symbologies Matrix 2 of 5
ScanPlus 1800 - Installation Manual
99
minimum length = 6 (*)
\46\59\06\60
5. Symbologies MSI Code
100
ScanPlus 1800 - Installation Manual
MSI Code
- numerical symbology
not active (*)
\41\59\60
active
\41\58\60
check digit
mod 10
checked and transmitted (*)
\44\5A\60
checked but not transmitted
\44\5C\60
double mod 10
checked and transmitted
\44\5B\60
checked but not transmitted
\44\5D\60
5. Symbologies MSI Code
ScanPlus 1800 - Installation Manual
101
barcode length
= <barcode data> + <check digit>
- minimum length possible = 2 characters
- use the "compose minimum length" option if you know the minimum length of the codes in your
application !!!
any length
\44\5F\00\60
- cancels the last minimum length selection and
accepts any valid length (2 or more characters)
compose minimum length: [range: 2-50]
\44\5F\60
- enter a number string and scan End Selection
(Appendix C)
- to optimize decoding performance and increase
security, select the same length as the minimum
length in your application (do not select a shorter
length !!)
minimum length = 6 (*)
\44\5F\06\60
5. Symbologies PDF417
102
ScanPlus 1800 - Installation Manual
PDF417
- two-dimensonal symbology only available with ScanPlus 1800 PDF
- alphanumeric full ASCII symbology - letter case defined
active (*)
\48\4D\60
- only available with ScanPlus 1800 PDF
not active
\48\4E\60
macro PDF
- macro PDF is used when :
- a long message requires more than one PDF417 label
- "optional fields" information must be transmitted to the host application
buffered (*)
\48\4F\01\60
- stores a multi-label PDF417 message in the
ScanPlus buffer
- transmits the whole message when all the
labels have been read
- you can read the labels in any order
- flashing green LED = end of read but message
not finished (read the next label)
- good read beep = end of message (message
transmitted and no green LED)
5. Symbologies PDF417
ScanPlus 1800 - Installation Manual
103
- error beeps = you have already read this label
(read another label) or the buffer is full (the
message is too long, you will have to use the
"unbuffered" option)
unbuffered
\48\4F\00\60
- for multi-label PDF417 messages that are too
long for the ScanPlus buffer (memory overflow)
- each part of the message (PDF417 label) is
transmitted separately (the host application must
then assemble the message using the macro
PDF control header transmitted with each label)
- good read beep and transmission each time a
you read a label
control header
- only present in macro PDF codes
- always transmitted with "unbuffered" option
not transmitted (*)
\48\50\00\60
transmitted
\48\50\01\60
Produkt Specifikationer
| Mærke: | Intermec |
| Kategori: | Stregkodelæser |
| Model: | ScanPlus 1800PDF |
Har du brug for hjælp?
Hvis du har brug for hjælp til Intermec ScanPlus 1800PDF stil et spørgsmål nedenfor, og andre brugere vil svare dig
Stregkodelæser Intermec Manualer
1 September 2024
24 August 2024
19 August 2024
14 August 2024
7 August 2024
5 August 2024
1 August 2024
31 Juli 2024
28 Juli 2024
24 Juli 2024
Stregkodelæser Manualer
- Stregkodelæser Nilox
- Stregkodelæser IFM
- Stregkodelæser Motorola
- Stregkodelæser Nedis
- Stregkodelæser Casio
- Stregkodelæser Palm
- Stregkodelæser Trimble
- Stregkodelæser Honeywell
- Stregkodelæser König
- Stregkodelæser Deltaco
- Stregkodelæser Digitus
- Stregkodelæser Zebra
- Stregkodelæser Olympia
- Stregkodelæser ELO
- Stregkodelæser Datalogic
- Stregkodelæser Newland
- Stregkodelæser Renkforce
- Stregkodelæser Manhattan
- Stregkodelæser DeLOCK
- Stregkodelæser Opticon
- Stregkodelæser Qian
- Stregkodelæser Godex
- Stregkodelæser Steren
- Stregkodelæser Argox
- Stregkodelæser IC Intracom
- Stregkodelæser Adesso
- Stregkodelæser POSline
- Stregkodelæser Metapace
- Stregkodelæser Wasp
- Stregkodelæser Approx
- Stregkodelæser Brady
- Stregkodelæser Baracoda
- Stregkodelæser Posiflex
- Stregkodelæser Datamax-O'neil
- Stregkodelæser CipherLab
- Stregkodelæser Cypress
- Stregkodelæser DENSO
- Stregkodelæser Socket Mobile
- Stregkodelæser Mach Power
- Stregkodelæser QUIO
- Stregkodelæser EC Line
- Stregkodelæser Tecno
- Stregkodelæser ZBA
- Stregkodelæser Code Corporation
- Stregkodelæser Hamlet
- Stregkodelæser Qoltec
- Stregkodelæser Vultech
- Stregkodelæser Psion
- Stregkodelæser Koamtac
- Stregkodelæser Unitech
- Stregkodelæser Atlantis Land
- Stregkodelæser ID-Tech
- Stregkodelæser Code
- Stregkodelæser Bluebird
- Stregkodelæser Cognex
Nyeste Stregkodelæser Manualer
24 Marts 2025
24 Marts 2025
26 Februar 2025
23 Februar 2025
23 Februar 2025
23 Februar 2025
23 Februar 2025
23 Februar 2025
21 Februar 2025
20 Februar 2025