JL Audio M3-770ETXv3 Manual

JL Audio Højttaler M3-770ETXv3

Læs nedenfor 📖 manual på dansk for JL Audio M3-770ETXv3 (1 sider) i kategorien Højttaler. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
M3/M6-ETXv3 - Enclosed Speaker Systems
with Integrated RGB LED Lighting (optional)
Physical Specifications M3-770ETXv3 M6-770ETXv3 M6-880ETXv3
Enclosure Diameter (A) 7.70 in / 196 mm 7.70 in / 196 mm 8.80 in / 224 mm
Enclosure Depth-Classic (B) 12.62 in / 321 mm 12.62 in / 321 mm 14.73 in / 374 mm
Enclosure Depth-Sport (B) 12.69 in / 323 mm 12.67 in / 322 mm 14.80 in / 376 mm
Height including Mounting Fixture Receiver* (C) 8.74 in / 222 mm 8.74 in / 222 mm 9.67 in / 246 mm
Mounting Fixture Receiver / Enclosure Offset (D) 1.04 in / 26 mm 1.04 in / 26 mm 0.87 in / 22 mm
*Mounting Fixtures Required (sold separately)
General Specifications M3-770ETXv3 M6-770ETXv3 M6-880ETXv3
System Nominal Impedance 4 Ω 4 Ω 4 Ω
System Frequency Response 45 Hz - 25 KHz ± 3 dB 45 Hz - 25 KHz ± 3 dB 38 Hz - 20 KHz ± 3 dB
System Efficiency 90.5 dB @ 1 W / 1 m 91.0 dB @ 1 W / 1 m 90.5 dB @ 1 W / 1 m
Continuous Power Handling (RMS) 70 W 100 W 125 W
Peak Music Power 140 W 200 W 250 W
Recommended RMS Amplifier Power (per Ch.) 20 - 140 W 40 - 200 W 50 - 250 W
Thank you for choosing JL Audio Marine
Enclosed Speaker Systems. With proper
installation, your new speakers will deliver years
of listening pleasure.
We strongly recommend that you have your
Enclosed Speaker Systems installed by your
authorized JL Audio dealer. The installation
professionals employed by your dealer have the
necessary tools and experience to properly install
this product. If you prefer to perform your own
installation, please read this and the instructions
included with your Mounting Fixtures (sold
separately) completely before beginning the process.
Installation of this product requires use of
JL Audio® Mounting Fixtures (sold separately).
No other method of installation should be
attempted. To avoid injury, installation
instructions included with the JL Audi.
Mounting Fixtures MUST be followed precisely.
Do not attempt to remove the LEDs from from the
speakers. The LEDs are permanently fixed and
attempting to remove them will cause damage and
this damage will not be covered under warranty.
LED EQUIPPED MODELS
Illuminated speaker models are outfitted with
multi-color RGB LEDs to produce vibrant accent
lighting. Refer to the Wiring Harness Info table for
individual RGB wire connection info.
Note: Wiring connections at each speaker location
are required for LED functionality.
Adjustable control of RGB lighting may be
achieved with the use of an RGB lighting controller
(sold separately). Note: When selecting an RGB
lighting controller, make sure that the total
amperage demands of all LED circuits does not
exceed the output capacity of the controller.
Refer to the RGB LED Specifications table for the
individual current draw amounts and sum (add)
the total. For optimal performance, we recommend
using the JL Audio marine lighting controller
(MLC-RW).
DIRECT LED WIRING
Alternatively, you may hard wire individual leads
or a combination of leads to achieve up to seven
different LED color assortments. Refer to the Direct
LED Wiring Info table for the wire colors used to
achieve specific LED colors.
Wiring Harness Info
Wire Size Wire Color Use
16 AWG Red/Stripe Speaker Positive (+)
Black/Stripe Speaker Negative (–)
20 AWG
Red Red RGB LED Negative (–)
Green Green RGB LED Negative (–)
Blue Blue RGB LED Negative (–)
Yellow Main RGB LED Positive (+12V)
Note: Not all wires may be used in normal applications. Refer to the
instructions of your RGB lighting controller for specific connection info.
Direct LED Wiring Info
LED Color Wire Color(s) Connection
Red Red
Combine selected
wires from all
speakers and connect
to negative ground
or to the negative (–)
battery post.
Green Green
Blue Blue
Yellow Red and Green
Pink Red and Blue
Aqua Green and Blue
White Red, Green and Blue
Combine all YELLOW (+12V) leads together (parallel)
and connect to a switched +12V supply. See below for
additional info.
RGB LED Specifications
Specification M3-770ETXv3 M6-770ETXv3 M6-880ETXv3
LED Current
Draw at 12V DC 108 mA 324 mA 486 mA
Recommended
Fuse Value 150 mA 500 mA 750 mA
LED Voltage
Range 10 - 14.4V DC
LED WIRING CONSIDERATIONS
Do not connect to 24V electrical systems.
Do not connect the speakers’ LED lights to the
vessels navigational lighting circuits.
For short-circuit protection, we recommend
installing a fuse (not included) at EACH speaker’s
YELLOW (+12V) LED power connection lead.
Refer to the RGB LED Specifications table for
recommended fuse ratings.
We recommend a minimum of 16AWG wire size
for each speaker’s LED connection circuits.
In addition to the above, we recommend
activating the speakers’ LEDs thru a cabin/
interior lighting circuit that supplies +12V via an
existing switch. If an existing switched circuit
is not available, you may install a dedicated
toggle/rocker style switch that will supply
positive (+12V) power. Fuse this main +12V
connection according to the total amperage
demands of all LED circuits. Refer to the RGB
LED Specifications table for individual current
draw amounts and recommended fuse ratings.
INCLUDED PARTS
Two Aluminum Logo Caps
• One Tube of Silicone Adhesive
• Eight Red Butt Splice Connectors (#22-18 AWG)
• Four Blue Butt Splice Connectors (#16-14 AWG)
M3-M6-ETXv3_061219_SKU#011540
B
A
C
NOTE: Illustration may not be to scale.
A
D
M6 Sport Grille Shown.


Produkt Specifikationer

Mærke: JL Audio
Kategori: Højttaler
Model: M3-770ETXv3

Har du brug for hjælp?

Hvis du har brug for hjælp til JL Audio M3-770ETXv3 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Højttaler JL Audio Manualer

Højttaler Manualer

Nyeste Højttaler Manualer