JL Audio MMR-10W Manual

JL Audio Fjernbetjening MMR-10W

Læs nedenfor 📖 manual på dansk for JL Audio MMR-10W (2 sider) i kategorien Fjernbetjening. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

FCC Compliance Statement

NOTE: This equipment has been tested and found to comply with

the limits of Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from

that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Any changes or modications not expressly approved by the party

responsible for compliance could void the user’s authority to operate

this equipment.

Safety Considerations

• Install the receiver module in a dry, well-ventilated location that

does not interfere with your factory-installed systems. If a dry

environment is not available, a location that is not exposed to

heavy splashing may be used. Do not install where it will be directly

exposed to the elements.

• Securely mount the receiver module to avoid coming loose in the

event of a collision, sudden jolt or as a result of repeated vibrations

during normal use.

• While the remote transmitter is designed to be water-resistant, it

should never be submerged under water for prolonged periods or

subjected to high-pressure water spray.

• Do not mount the remote cradle or receiver module in an engine

compartment or areas of extreme heat. Areas exposed to a heater or

hot air should also be avoided.

• Check before drilling to make sure that you will not be drilling into

an exterior panel/hull, fuel tank, gas/brake line, wiring harness or

other vital system.

• Protect all wiring from sharp edges and wear by carefully routing

them, tying them down and using grommets and loom where

appropriate. Secure all wiring using cable ties or wire clamps,

as needed.

Installation Applications

This product is designed for operation in 12 volt, negative-ground

electrical systems. Using this product in systems with positive ground

and/or voltages other than 12 volts may result in damage to the

product and will void the warranty. This product is not certied or

approved for use in aircraft.

What is Included

(1) MMR-10W Remote Transmitter

(1) Remote Cradle

(2) Plastic cable ties

(1) Flat head screw

(1) User Manual

Also Included (MMR-10W only)

(1) MMR-10W Receiver Module

(2) Pan head screws

(1) Quick-release lanyard

Product Description

The MMR-10W is a wireless remote controller designed to add

handheld control functionality to MediaMaster® source units.

Utilizing state-of-the-art, 2.4 GHz wireless technology, the MMR-

10W permits control of your MediaMaster® source unit (with LED

signal conrmation), from up to 150 ft. (45 m) away. The MMR-10W

system consists of a hideaway receiver module and water-resistant

(IP67 rated) remote transmitter. The receiver module is designed to

connect directly to your MediaMaster® and is programmable, with

the ability to pair with up to ten MMR-10W remote transmitters.

A versatile mounting cradle is included, along with a lanyard for

convenient, on-the-go functionality.

IP67 Water Resistance Rating

The MMR-10W remote transmitter has been tested to withstand

immersion in water, up to 1 meter (3.28 ft.) deep, for up to 30 minutes.

Note: While designed to be water resistant, the remote should never

be submerged under water for prolonged periods or subjected to

activity that creates pressure on it that exceeds its depth rating.

Receiver Module Placement & Connection

While the MMR-10W receiver module can be mounted in any

orientation, its installation location should be considered to

optimize RF performance. For example, we recommend that you

avoid mounting the receiver module directly to metal surfaces or

to wire harnesses, especially those containing high-current circuits.

Mounting locations in close proximity to other electronics should also

be avoided to minimize wireless interference. Use the two supplied

pan head screws to mount the receiver module.

The receiver module is designed to connect directly to the 5-pin

“Remote” plug of your MediaMaster®. Use caution when mating

the connectors, as they are keyed and must be aligned to t

properly. Note: If a MMR-20 wired remote controller is installed

with your MediaMaster®, you may use a Y-adaptor (MMC-2Y)

(sold separately) to add/connect the MMR-10W receiver module.

If space directly behind your MediaMaster® is limited, you

may use a remote controller cable (MMC-6 or MMC-25) (each

sold separately) to extend the receiver module’s mounting

options. Once connected, make sure that cables are securely

routed using cable ties and wire clamps, keeping connections

away from areas where they could be submerged in water.

MediaMaster® Wireless Remote Controller

MMR-10W / MMR-10W-Remote

Remote Cradle Mounting

For convenience, a plastic cradle is included to mount the MMR-

10W remote transmitter. The base of the cradle is designed so it can

be installed on a at surface or a tubular structure, such as a pipe/

rail or steering wheel. Note: Select a location that does not interfere

with other factory installed devices or safety equipment. Refer to the

following installation examples for more information.

Surface Mount Example

Attach to a at surface using

the included at head screw.

Pipe/Rail Mount Example

Attach to a straight pipe/rail

using the included plastic

cable ties.

Produkt Specifikationer

Mærke:	JL Audio
Kategori:	Fjernbetjening
Model:	MMR-10W

Har du brug for hjælp?

Hvis du har brug for hjælp til JL Audio MMR-10W stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fjernbetjening JL Audio Manualer

JL Audio MMR-25W Manual

31 August 2024

JL Audio HD-RLC Manual

30 August 2024

JL Audio M-RBC-1 Manual

22 Juli 2024

JL Audio MMR-10W Manual

20 Juli 2024

JL Audio VXi-HUB Manual

10 April 2024

JL Audio VXi-BTC Manual

29 August 2023

JL Audio MMR-20-BE Manual

4 August 2023

JL Audio RBC-1 Manual

12 Juli 2023

JL Audio CL-RLC Manual

26 November 2022

JL Audio MVi-DRCADAPT Manual

19 November 2022

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

Morel MPS-R1 Manual

18 November 2024

One For All URC 2110 Manual

16 November 2024

One For All KE4910 Manual

16 November 2024

Interphone Handlebar Control Manual

2 November 2024

Canon BG-E20 Manual

12 Oktober 2024

Logitech Harmony 785 Manual

8 Oktober 2024

DSC WS4949 Manual

8 Oktober 2024

Neewer RT112 Manual

7 Oktober 2024

Neewer RT113 Manual

7 Oktober 2024

MB Quart N1-RC Wireless Manual

6 Oktober 2024