Kenwood DDX7018BT Manual

Kenwood Ikke kategoriseret DDX7018BT

Læs nedenfor 📖 manual på dansk for Kenwood DDX7018BT (68 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 32 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/68

DDX7018BT (Region 3 – DVD Region Code 3 Area)

DDX7018BTM (Region 2 – DVD Region Code 2 Area)

DDX718WBT (Region 3 – DVD Region Code 3 Area)

DDX718WBTM (Region 2 – DVD Region Code 2 Area)

B5A-2147-20 (MN/M2N/XN/A9N)

ENGLISH

This instruction manual is used to describe the models listed above. Model availability and features (functions) may differ depending on the country and

sales area.

DMX7018BT (For Australia and New Zealand)

DMX7018BT (For Southeast Asia)

DMX7018BTM

DMX718WBT (For Australia and New Zealand)

DMX718WBT (For Southeast Asia)

DMX718WBTM

MONITOR WITH DVD RECEIVER MONITOR WITH RECEIVER

INSTRUCTION MANUAL

Important Notice

Important NoticeImportant Notice

To ensure proper use, please read through this

manual before using this product. It is especially

important that you read and observe WARNINGS

and CAUTIONS in this manual.

Please keep the manual in a safe and accessible

place for future reference.

WARNINGS

To prevent accidents and damages

• DO NOT install any unit or wire any cable in a

location where;

–it may obstruct the steering wheel and gearshift

lever operations.

–it may obstruct the operation of safety devices such

as air bags.

–it may obstruct visibility.

• DO NOT raise the volume level too much, as this will

make driving dangerous by blocking outside sounds,

and may cause hearing loss.

• DO NOT operate the unit while driving. If you need

to operate the unit while driving, be sure to look

around carefully.

• Stop the car before performing any complicated

operations.

• The driver must not watch the monitor while driving.

CAUTIONS

To care for the unit

• If you have parked the car for a long time in hot or

cold weather, wait until the temperature in the car

becomes normal before operating the unit.

To care for the monitor

• The monitor built into this unit has been produced

with high precision, but it may have some ineffective

dots. This is inevitable and is not considered

defective.

• Do not expose the monitor to direct sunlight.

• Do not operate the touch panel using a ball-point

pen or similar tool with a sharp tip.

Touch the keys on the touch panel with your finger

directly (if you are wearing a glove, take it off).

• When the temperature is very cold or very hot...

–Chemical changes occur inside, causing

malfunction.

–Pictures may not appear clearly or may move

slowly. Pictures may not be synchronized with

the sound or picture quality may decline in such

environments.

On the volume setting

• Digital devices produce very little noise compared

with other sources. Lower the volume before playing

these digital sources to avoid damaging the speakers

by sudden increase of the output level.

For DDX7018BT/DDX7018BTM/DDX718WBT/

DDX718WBTM:

The marking of products using lasers

The label is attached to the chassis/case and says

that the component uses laser beams that have been

classified as Class 1. It means that the unit is utilizing

laser beams that are of a weaker class. There is no

danger of hazardous radiation outside the unit.

ENGLISHi

Important Notice

Important NoticeImportant Notice

For DDX7018BTM/DMX7018BTM/DDX718WBTM/

DMX718WBTM:

For Turkey

Bu ürün 28300 sayılı Resmi Gazete’de yayımlanan Atik

Elektrikli ve Elektronik Eşyalarin Kontrolü Yönetmeliğe

uygun olarak üretilmiştir.

Eski Elektrik ve Elektronik Ekipmanların İmha

Edilmesi Hakkında Bilgi (ayrı atık toplama

sistemlerini kullanan ülkeleri için uygulanabilir)

Sembollü (üzerinde çarpı işareti olan

çöp kutusu) ürünler ev atıkları olarak

atılamaz. Eski elektrik ve elektronik

ekipmanlar, bu ürünleri ve ürün atıklarını

geri dönüştürebilecek bir tesiste

değerlendirilmelidir. Yaşadığınız bölgeye

en yakın geri dönüşüm tesisinin yerini

öğrenmek için yerel makamlara müracaat

edin. Uygun geri dönüşüm ve atık

imha yöntemi sağlığımız ve çevremiz

üzerindeki zararlı etkileri önlerken

kaynakların korunmasına da yardımcı

olacaktır.

For DDX7018BTM/DMX7018BTM/DDX718WBTM/

DMX718WBTM:

Declaration of Conformity with regard to the

RE Directive 2014/53/EU

Declaration of Conformity with regard to the

RoHS Directive 2011/65/EU

Manufacturer:

JVC KENWOOD Corporation

3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi,

Kanagawa, 221-0022, Japan

EU Representative:

JVCKENWOOD Europe B.V.

Amsterdamseweg 37, 1422 AC UITHOORN,

THE NETHERLANDS

English

Hereby, JVCKENWOOD declares that the radio

equipment “DDX7018BTM/DMX7018BTM/

DDX718WBTM/DMX718WBTM” is in compliance with

Directive 2014/53/EU.

The full text of the EU declaration of conformity is

available at the following internet address:

http://www.kenwood.com/cs/ce/eudoc/

Turkish

Burada, JVCKENWOOD “DDX7018BTM/DMX7018BTM/

DDX718WBTM/DMX718WBTM” radyo ekipmanının

2014/53/AB Direktifine uygun olduğunu bildirir.

AB uyumluluk deklarasyonunun tam metni aşağıdaki

internet adresinde mevcuttur.

http://www.kenwood.com/cs/ce/eudoc/

ENGLISH ii

About this manual

The displays and panels shown in this manual are

examples used to provide clear explanations of the

operations. For this reason, they may be different

from the actual displays or panels.

Illustrations of are mainly used for DDX7018BT

explanation.

This manual mainly explains operations using the

buttons on the monitor panel and keys on the

touch panel. For operations using the remote

controller, see page 43.

< > indicates the various screens/menus/

operations/settings that appear on the touch

panel.

[ ] indicates the keys on the touch panel.

Indication language: English indications are used

for the purpose of explanation. You can select the

indication language from the menu. <SETUP>

(Page 40)

Contents

ContentsContents

Component Names and Operations ...............3

Basic Operations .................................................4

Turning on the power .................................................................. 4

Turning off the power/turning off the AV source .......4

Putting the unit in standby .......................................................4

Turning off the screen ..................................................................4

Adjusting the volume ...................................................................5

Attenuating the sound ................................................................5

Monitor panel operations ..........................................................5

Getting Started ...................................................6

Initial settings ..................................................................................... 6

Setting the security function....................................................6

Calendar/clock settings ...............................................................7

Various Screens and Operations .....................7

Touch screen operations ............................................................ 7

Home screen ......................................................................................8

Source control screen ...................................................................9

List/setting screen........................................................................11

Disc ......................................................................12

Video ...................................................................14

USB ......................................................................15

iPod/iPhone .......................................................17

Apps—WebLink™ .............................................18

Radio ...................................................................19

Spotify ................................................................22

Other External Components ..........................23

View camera ....................................................................................23

AV-IN .....................................................................................................24

Watching TV ....................................................................................24

Using the external navigation unit ....................................25

Bluetooth® .........................................................26

Information ......................................................................................26

Preparation .......................................................................................26

Connection.......................................................................................26

Bluetooth mobile phone .........................................................29

Bluetooth audio player ............................................................. 32

Bluetooth mobile phone settings ......................................32

Settings ..............................................................33

Audio settings ................................................................................33

AV settings ........................................................................................ 37

Display settings ..............................................................................38

User interface settings ...............................................................39

Camera settings ............................................................................ 40

Special system settings .............................................................41

Bluetooth settings ....................................................................... 42

Security settings ............................................................................42

Navigation settings ..................................................................... 42

Remote Controller ............................................43

Preparation .......................................................................................43

Basic operations for RC-DV340 (supplied) .................... 43

Basic operations for KNA-RCDV331 (optionally

purchased) ........................................................................................45

Installation and Connection ...........................46

Before installation ........................................................................ 46

Installing the unit..........................................................................48

Connecting external components .................................... 48

Wiring connection ....................................................................... 49

References .........................................................53

Maintenance ...................................................................................53

More information .........................................................................53

Troubleshooting ...............................................56

Specifications ....................................................59

Trademarks and licenses ..........................................................62

2ENGLISH

Component Names and Operations

Component Names and OperationsComponent Names and Operations

DDX7018BT/DDX7018BTM

DMX7018BT/DMX7018BTM

1 Remote sensor*1

2 Screen (touch panel)

3 Monitor panel

4 / buttonVOLUME K J

5 buttonCAM/DISP OFF

• (Press): Displays the picture from the CAM

connected rear view camera.

• (Hold): Turns off the screen.DISP OFF

6 HOME button

• (Press): Turns on the power.

• (Hold): Turns off the power or AV source.*2

• (Press): Displays the Home screen while HOME

the power is on.

7 buttonMENU/ATT

• (Press): Pops up the short-cut menu.MENU

• (Hold): Attenuates the sound.ATT

8 button/VOICE

• (Press): Displays the App screen. (Page 18)

• (Hold): Activates the voice dialing.VOICE

9 : buttonDDX7018BT/DDX7018BTM M

Displays the screen. (Page 5)<Angle Adjust>

DMX7018BT/DMX7018BTM: buttonAV

Switches the screen between the navigation and

the current source.

p Built-in Bluetooth microphone*3

DDX718WBT/DDX718WBTM/DMX718WBT/

DMX718WBTM

1 Monitor panel

2 Screen (touch panel)

3 button

• Press: Displays the App screen. (Page 18)

• Hold: Activates voice dialing.

4 Volume J K/ buttons

5 buttonHOME

• Turns on the power. (Press)

• Displays the Home screen while the power is on.

(Press)

• Turns off the power or AV source.*2 (Hold)

6 buttonMENU

• Pops up the short-cut menu. (Press)

• Attenuates the sound. (Hold)

7 buttonCAM

• Displays the picture from the connected rear

view camera. (Press)

• Turns off the screen. (Hold)

8 Remote sensor*1

*1 DO NOT expose the remote sensor to bright light (direct sunlight

or artificial lighting).

*2 The function of the button when held varies depending on

the <Manual Power OFF> setting on the <Special> screen.

(Page41)

*3 Only for DDX7018BT/DMX7018BT Southeast Asian models/

DMX7018BT Indonesian models.

3ENGLISH

Putting the unit in standby

1 Display the source/option selection

screen.

On the Home screen, touch as follows:

2 Put the unit in standby.

On the source/option selection screen, touch as

follows:

Basic Operations

Basic OperationsBasic Operations

Turning on the power

DDX7018BT

DDX7018BTM

DMX7018BT

DMX7018BTM

DDX718WBT

DDX718WBTM

DMX718WBT

DMX718WBTM

Turning off the power/turning off the AV

source

• This function varies depending on the <Manual

Power OFF> setting. (Page 41)

DDX7018BT

DDX7018BTM

DMX7018BT

DMX7018BTM

DDX718WBT

DDX718WBTM

DMX718WBT

DMX718WBTM

(Hold) (Hold)

Turning off the screen

On the monitor panel

DDX7018BT

DDX7018BTM

DMX7018BT

DMX7018BTM

DDX718WBT

DDX718WBTM

DMX718WBT

DMX718WBTM

(Hold) (Hold)

To turn on the screen: Press the same button on the

monitor panel or touch the screen.

On the pop-up short-cut menu

1 Display the pop-up short-cut menu.

DDX7018BT

DDX7018BTM

DMX7018BT

DMX7018BTM

DDX718WBT

DDX718WBTM

DMX718WBT

DMX718WBTM

2 On the pop-up short-cut menu, touch as

follows:

Display OFF

To turn on the screen: Touch the screen.

4 ENGLISH

Basic Operations

Basic OperationsBasic Operations

Adjusting the volume

DDX7018BT

DDX7018BTM

DMX7018BT

DMX7018BTM

DDX718WBT

DDX718WBTM

DMX718WBT

DMX718WBTM

You can adjust the volume (00 to 40) by pressing to J

increase and pressing to decrease.K

• Holding J increases the volume continuously to

level 15.

Attenuating the sound

DDX7018BT

DDX7018BTM

DMX7018BT

DMX7018BTM

DDX718WBT

DDX718WBTM

DMX718WBT

DMX718WBTM

(Hold) (Hold)

The ATT indicator lights up.

To cancel attenuation: Press and hold the same

button again.

Monitor panel operations

1 Display the <Angle Adjust> screen.

DDX7018BT/DDX7018BTM:

DMX7018BT/DMX7018BTM/DDX718WBT/

DDX718WBTM/DMX718WBT/DMX718WBTM:

Press on the monitor panel to display the MENU

pop-up short-cut menu, then touch .[Angle]

2 Perform the adjustment or operation.

E.g. Angle adjust screen for DDX7018BT

[0] – [6] Selects a monitor angle.

(The monitor panel will stay in

this angle when you turn on

the unit.)

<Off Position> Sets the angle of the monitor

panel you want when you

turn off the unit or the ignition

switch of the vehicle.

• Select the monitor angle,

then touch .[Memory]

[M DISC EJECT] (Only for DDX7018BT/

DDX7018BTM/DDX718WBT/

DDX718WBTM)

(Touch) Ejects the disc.

To return the monitor panel to

the selected angle:

Press M on the monitor panel.

• To return to the previous screen, touch [ ] on the

setting screen.

5ENGLISH

Initial settings

When you power on the unit for the first time, the

<Initial SETUP> screen appears.

Perform the initial settings.

E.g. Initial settings screen for DDX7018BT

Once completed, a warning message appears. Touch

[Agree] to display the Home screen.

[Language]*

Select the text language used for on-screen

information.

Touch , then select the language.[Language Select]

• (Initial)American English(en)/British English(en) /

Nederlands(nl)/Français(fr)/Deutsch(de)/

Italiano(it)/Español(es)/(ar) /Ελληνικά(el)/

Português(pt)/Čeština(cs)/Polski(pl)/

Magyar(hu)/Руccĸий(ru)/ (th)/

Türkçe(tr)/ (zh)/ (zh)/

(he) /(fa) /BahasaMelayu(ms)/Bahasa

Indonesia(id)

Getting Started

Getting StartedGetting Started

[Clock] (Page7)

Set the calendar and clock time.

Make the settings for , or [Clock] [Time Zone] [Clock

Adjust].

[Display] (Page38)

Make the settings to adjust the display.

[Camera] (Page40)

Make the settings to display the picture from the

connected view camera.

[DEMO]

• (Initial): Activates the display demonstration.ON

• : Deactivates the display demonstration.OFF

* Only for DDX7018BT/DDX7018BTM/DDX718WBT/DDX718WBTM:

“Please Power Off” appears when the setting is changed. To

enable the change:

For DDX7018BT/DDX7018BTM:

– When <Manual Power OFF> is set to [AV OFF], turn off the

ignition switch, then turn on the ignition switch.

– When <Manual Power OFF> is set to [Complete OFF], turn off

the power of the unit, then turn on the power of the unit.

For DDX718WBT/DDX718WBTM:

– Turn off the ignition switch, then turn on the ignition switch.

Setting the security function

Registering a security code

You can set a security code (four-digit number of

your choice) to protect your receiver system against

theft. Once you set the security code, you are required

to input the security code when the power is on to

reconnect the battery.

1 Display the Home screen.

DDX7018BT

DDX7018BTM

DMX7018BT

DMX7018BTM

DDX718WBT

DDX718WBTM

DMX718WBT

DMX718WBTM

2 Display the <Security Code Set> screen.

On the Home screen, touch as follows:

Then, on the screen, touch as follows:<SETUP>

[Security] [Security Code Set] 

6ENGLISH

2 Display the <User Interface> screen.

On the Home screen, touch as follows:

Then, on the screen, touch <SETUP> [User

Interface].

3 Set the date and clock.

[Clock]

Select the method to set the date and clock.

• (Initial): Synchronizes the clock with RDS-SYNC

the FM Radio Data System.

• : Sets the date and clock manually.Manual

For Indonesian models, is selected [Manual]

initially.

[Time Zone]*

Select the time zone for your area.

[Clock Adjust]*

Set the date and clock manually when is [Clock]

set to .[Manual]

Touch [J K] [/ ] to adjust the date (year/month/

date), then clock (hour/minute). To finish setting,

touch .[Set]

* Available when [Clock] is set to [Manual].

Getting Started

Getting StartedGetting Started Various Screens and

Various Screens and

Various Screens and Various Screens and

Operations

OperationsOperations

3 Enter a four-digit number ( ), then 1

confirm the entry ( 2).

• To clear the last entry, touch .[BS]

• To cancel the setting, touch .[ ]

4 Enter the four-digit number entered in

step 3 and touch [Enter] again to confirm

your security code.

To change the security code: [Security Code Touch

Change] <Security> on the screen on step 2, then

repeat steps 3 and 4.

To clear the security code: [Security Code Touch

Cancellation] <Security> on the screen on step2,

then repeat step 3.

Calendar/clock settings

1 Display the Home screen.

DDX7018BT

DDX7018BTM

DMX7018BT

DMX7018BTM

DDX718WBT

DDX718WBTM

DMX718WBT

DMX718WBTM

You can display or change to other screens at any time

to show information, change the AV source, change

the settings, etc.

Touch screen operations

To perform operations on the screen, you need to

touch, touch and hold, flick or swipe to select an item,

display setting menu screen or to change the page,

etc.

Touch

Touch the screen gently to select an

item on the screen.

Touch and hold

Touch the screen and keep your

finger in place until the display

changes or a message is displayed.

Flick

Slide your finger to the left or right on

the screen to change the page.

Swipe

Slide your finger up or down on the

screen to scroll the screen.

7ENGLISH

Home screen

When you turn on the power for the first time, the

Home screen appears.

• You can customize the Home screen.

• To display the Home screen from other screens, press

HOME on the monitor panel.

E.g. Home screen for DDX7018BT

Touching the operation keys performs the following

actions:

1 Displays the current playing source control screen

2 Clock/date

3 Current source information

4 Displays all playback sources and options

5 Short-cut playback source keys

6 Displays the phone control screen

Available playback sources and options

Touch 4 to display the source/option selection screen.

Radio

iPod DISC USB

E.g. Source/option selection screen for DDX7018BT

Touching the operation keys performs the following

actions:

[WebLink] Switches to the WebLink™

application.

[Bluetooth] Plays a Bluetooth audio player.

[Radio] Switches to the radio broadcast.

[Spotify] Switches to the Spotify application.

[iPod] Plays an iPod/iPhone.

[DISC]* Plays a disc.

[USB] Plays files on a USB device.

[AV-IN] Switches to an external component

connected to the AV-IN input

terminal.

Various Screens and Operations

Various Screens and OperationsVarious Screens and Operations

[Audio] Displays the sound adjustment

screen.

[STANDBY] Puts the unit in standby.

[NAV] Displays the navigation screen

when a navigation unit is

connected.

[ ] Displays the screen.<SETUP>

To change the page: [ Touch ]/[ ]. Current page is

shown by the page indication on the bottom of the

screen.

To return to the Home screen: [ Touch ] on the

source/option selection screen.

* Only for DDX7018BT/DDX7018BTM/DDX718WBT/D

8 ENGLISH

Various Screens and Operations

Various Screens and OperationsVarious Screens and Operations

Source control screen

You can perform the playback operation from the

source control screen during playback.

• The operation keys and information displayed vary

depending on the selected source/disc type/file type

being played.

• If the operation keys are not displayed on the screen,

touch the screen to show them.

E.g. Common audio playback source screen for

DDX7018BT

1 Playback source or media type

2 Picture data/artwork (shown if the file contains

artwork except for disc playback)

3 For video: Hides the operation buttons on the

screen while video is played

• Touch the screen to restore the operation

buttons.

For audio: File format

4 Repeat/random playback mode keys*1

5 Information about connected device

• For Bluetooth device: Signal strength and battery

level (only when the information is acquired from

the device)

6 Track/file/song/video information

• Touching [

] scrolls the text if not all of the text

is shown.

7 Clock display

8 Displays the track/file/station/channel list

9 Displays/hides other available operation keys*1

p Displays the source/option selection screen

q Operation keys*1

w Secondary screen

Each time you touch , the items shown on [ ]/[ ]

the secondary screen change as follows:

• Indicators: Displays the current source conditions,

etc.

The followings are the common indicators:

− : The sound is attenuated.ATT

− : The loudness is active.LOUD

− : A disc is inserted.*2IN

− : Music/video file is played back.MUSIC/VIDEO

• Short-cut buttons: Changes the source from

those you have located on the Home screen.

• Current source information while the navigation

screen is displayed: Touching the information

area displays the source control screen.

e Displays the phone control screen

*1 See “Common operation keys on source control screen

page 10.

*2 Only for DDX7018BT/DDX7018BTM/DDX718WBT/

Customizing the source/option selection

screen

You can arrange the items to display on the source/

option selection screen.

1 Select an item to move.

Touch and hold the item you want to move until

boxes appear around the icons.

2 Drag the selected item to the position you

want to move it to.

Radio

iPod DIS USB

E.g. Source/option selection screen for DDX7018BT

About short-cut playback source keys on the

Home screen

The three items displayed on the top of the source/

option selection screen with large icons are also

shown on the Home screen as the short-cut playback

source keys. You can set the source keys which you use

frequently and access quickly from the Home screen.

9ENGLISH

Various Screens and Operations

Various Screens and OperationsVarious Screens and Operations

Common operation keys on source control screen

• The appearance of the operation keys may differ,

however the similar operation keys have the same

operations.

• Available operation keys differ depending on the

selected source or connected device.

Touching the operation keys performs the following

actions:

[ ]* Selects repeat playback mode.

• : Repeat one

• : Repeat folder

• ALL: Repeat all

• CAP: Repeat chapter

• TIT: Repeat title

• (gray): Off

[ ]* Selects random playback mode.

• : Random folder

• ALL: Random all

• (gray): Off

[ ] Displays other available operation keys

besides those shown on .q

• To hide the window, touch [ ].

[ ] [ ] Reverses/forwards search during

playback.

[ ] [ ] Plays in slow-motion.

[o]Stops playback.

[SETUP] Displays the setting screen of the

current playback source.

[MENU CTRL] Displays the video menu control

screen. (Page 14)

[ ][ ] Selects a folder.

[Audio] Changes the audio output channel

of VCD.

[ ] Attenuates/restores the sound.

[ ] Displays the folder list/track list/audio

menu/video menu.

[S T]/[ ] • (Touch) Selects an item (chapter/

folder/track/audio file/video file).

• (Hold) Reverses/forwards search.

• (Hold) Plays in slow-motion while

paused for video playback.

[IW]Starts/pauses playback.

* About playback mode:

– Available playback mode differs depending on the sourc

file type, connected device, etc.

– You cannot activate repeat playback mode and random

playback mode at the same time.

Using the pop-up short-cut menu

While displaying the source control screen, you can

jump to another screen by touching the operation

keys on the pop-up short-cut menu.

1 Display the pop-up short-cut menu.

DDX7018BT

DDX7018BTM

DMX7018BT

DMX7018BTM

DDX718WBT

DDX718WBTM

DMX718WBT

DMX718WBTM

10 ENGLISH

Various Screens and Operations

Various Screens and OperationsVarious Screens and Operations

Using touch screen operation during

playback

Touching the areas performs the following actions:

1 Displays the video control menu while playing a

video.

2 Displays the source control screen.

3 Goes to the previous chapter/track.*

4 Goes to the next chapter/track.*

* Not available for video from an external component (AV-IN).

List/setting screen

The followings are the common operation keys which

appear on the list/settings screen.

• The appearance of the operation keys may differ,

however the similar operation keys have the same

operations.

• Available operation keys differ depending on the

setting screens. Not all the following operation keys

are shown on every screen.

Touching the operation keys performs the following

actions:

1 Displays list type selection window.

2 Selects the file type ( : audio/ : video).[ ] [ ]

3 Exits from the current screen or returns to the

previous screen.

4 Scrolls the text if not all of the text is shown.

5 Play/search keys

• : Plays all tracks in the folder containing [ Play]I

the current track.

• : Enters alphabet search to list the items [ A-Z]

in alphabetical order. When a keypad appears,

touch the first letter you want to search for.

• : Returns to the root folder.[ Top]

• : Returns to the upper layer.[ Up]

6 Changes the page to display more items.

• : Scrolls the page.[ ]/[ ]J K

• : Jumps to the top or bottom page.[ ]/[ ]

2 Select an item to jump.

E.g. Pop-up short-cut menu screen for DDX7018BT

1 Displays the picture adjustment screen.

(Page 15)

2 Turns off the screen.

3 (for ): Camera DDX7018BT/DDX7018BTM

Displays the picture from the connected rear

view camera. (Page 23)

Angle (for DMX7018BT/DMX7018BTM/

DDX718WBT/DDX718WBTM/DMX718WBT/

DMX718WBTM): Displays the <Angle Adjust>

screen. (Page 5)

4 Displays the <SETUP> screen. (Page 37)

5 Displays the sound adjustment screen.

6 Displays the current source control screen.

7 Closes the pop-up short-cut menu.

8 Changes the playback source.

• The three short-cut playback source keys

displayed on the Home screen are displayed

on the short-cut menu.

9 Displays the phone control screen. (Page 30)

11ENGLISH

Disc

Disc Disc (Only for DDX7018BT/DDX7018BTM/DDX718WBT/DDX718WBTM)

• If a disc does not have a disc menu, all tracks on it will

be played repeatedly until you change the source or

eject the disc.

• For playable disc types, file types and other

information, see pages 53 and 54 .

• If “ ” appears on the screen, the unit cannot accept

the operation you have tried to do.

– In some cases, without showing “ ”, operations

will not be accepted.

• When playing back a multi-channel encoded disc,

the multi-channel signals are downmixed.

Inserting a disc

DDX7018BT/DDX7018BTM: Press on the monitor M

panel to display the screen, touch <Angle Adjust> [ M

DISC EJECT] to open the monitor panel, then insert

a disc.

Label side up

E.g. Inserting a disc for DDX7018BT

DDX718WBT/DDX718WBTM: Press on the MENU

monitor panel, touch on the pop-up short-cut [Angle]

menu to open the monitor panel, then insert a disc.

Label side up

E.g. Inserting a disc for DDX718WBT

• After the disc is loaded, the monitor panel closes

automatically.

The source changes to and playback starts.“DISC”

• The IN indicator lights up while a disc is inserted.

Ejecting a disc

1 Display the <Angle Adjust>.

DDX7018BT/DDX7018BTM: Press on the M

monitor panel.

DDX718WBT/DDX718WBTM: Press on the MENU

monitor panel, then touch on the pop-up [Angle]

short-cut menu.

2 Eject a disc.

On the screen, then touch as <Angle Adjust>

follows:

• When removing a disc, pull it out horizontally.

• You can eject a disc while playing another AV source.

• If the ejected disc is not removed within 15 seconds,

the disc is automatically inserted again into the

loading slot to protect it from dust.

To close the monitor panel:

On the touch panel: After removing the disc, touch [ M

DISC EJECT] <Angle Adjust> on the screen.

On the monitor panel (only for DDX7018BT/

DDX7018BTM): After removing the disc, press .M

12 ENGLISH

Disc

DiscDisc

[Menu Language]*

Select the initial disc menu language. (Initial:

English)

[Subtitle Language]*

Select the initial subtitle language or turn subtitles

off ( ). (Initial: )OFF English

[Audio Language]*

Select the initial audio language. (Initial: )English

You can change the dynamic range while playing

Dolby Audio encoded discs.

• : Reproduces powerful sound at a low Wide

volume level with its full dynamic range.

• : Reduces the dynamic range a little.Normal

• (Initial): Reproduces movie dialog more Dialog

clearly.

Select the monitor type to watch a wide screen

picture on the external monitor.

16:9 4:3 LB 4:3 PS (Initial)

* You can change these settings only while DVD is inserte

the language on the window, then touch [Close] to finish.

Settings for disc playback

• Available items shown on the screen <DVD SETUP>

differ depending on the type of disc/file being

played back.

1 Display the <DVD SETUP> screen.

On the source control screen, touch as follows:

2 Make the settings.

Playback operations

Audio playback information and key

operation

• For playback information, see “Source control screen”

on page 9.

• For key operations on the touch panel, see “Common

operation keys on source control screen” on

page 10.

Selecting a folder/track on the list

1 Display the folder/track list.

On the source control screen, touch as follows:

2 Select the item in the selected folder.

• For details about the list operation, see

page 11.

Select an item in each layer until you reach and

select the desired file.

ENGLISH

Video

VideoVideo

Video menu control operations

(Only for DDX7018BT/DDX7018BTM/

DDX718WBT/DDX718WBTM)

You can display the video menu control during video

playback.

• Available operation keys differ depending on the

selected disc type and file type.

1 Display the video menu control screen.

On the source control screen, touch as follows:

2 Perform the video operations.

E.g. Video menu control screen for DDX7018BT

Touching the operation keys performs the following

actions:

[Top] Displays the top menu (DVD).

[Menu] Displays the disc menu (DVD).

[Return] Returns to the previous screen.

[Enter] Confirms the selection.

[Highlight] Switches to the direct disc menu

selection mode. Touch the target

item to select.

• The menu screen disappears when

no operation is done for 5 seconds.

[ ] Returns to the playback screen.

[Angle] Selects the view angle.

[Subtitle] Selects the subtitle type.

[Audio] Selects the audio type.

[J K H I] [ ] [ ] [ ] Selects an item.

Playback operations

Video playback information on the source

control screen

E.g. Video playback source control screen for

DDX7018BT

1 Media type

2 Hides the operation buttons on the screen.

• Touch the screen to restore the operation

buttons.

3 Repeat/random playback mode keys

4 Current playback item information/audio format

5 Playback status/playing time

6 Indicators

• : Lights up when a disc is inserted.IN

• : Lights up when video is played.VIDEO

14 ENGLISH

Adjusting the picture

1 Display the pop-up short-cut menu.

DDX7018BT

DDX7018BTM

DMX7018BT

DMX7018BTM

DDX718WBT

DDX718WBTM

DMX718WBT

DMX718WBTM

2 Display the picture adjustment screen.

On the pop-up short-cut menu, touch as follows:

3 Adjust the picture.

Video

VideoVideo

<Backlight> Adjusts the brightness of the

backlight. (−4 to +4)

<Contrast> Adjusts the contrast. (−4 to +4)

<Brightness> Adjusts the brightness. (−4 to +4)

<Color>*1 Adjusts the color. (−4 to +4)

<Tint>*2 Adjusts the tint. (−4 to +4)

<Aspect> Selects the aspect ratio.

• : Changes the aspect ratio of Full

video and displays fully on the

screen.

• : Displays the video in Normal

the aspect ratio of 4:3.

• *3:Auto

– For discs: Video of 16:9 ratio is

displayed in the aspect ratio

of setting. Video of 4:3 <Full>

ratio is displayed in the aspect

ratio of setting.<Normal>

– For USB: Displays the video

fully on vertical or horizontal

with no ratio change.

• Adjustable items are different depending on the

current source.

• You can perform this function only when you have

applied the parking brake.

*1 Adjustable only during playback.

*2 Available only when the “AV-IN” or camera screen is displayed.

*3 Selectable only when video from a disc or USB device is played

back.

USB

USBUSB

You can connect a USB mass storage class device such

as a USB memory, digital audio player, etc. to the unit.

• For playable file types and other information, see

pages 53 and 55.

• You cannot connect a PC or portable HDD to the

USB input terminal.

• You cannot connect a USB device via a USB hub.

Connecting a USB device

• Use CA-U1EX for extending the cable if necessary.

(Max 500 mA, 5V)

USB device (commercially available)

Rear panel

• Only for DMX7018BT/DMX7018BTM/DMX718WBT/

DMX718WBTM: The unit is equipped with two USB

input terminals. You can connect two USB devices.

15ENGLISH

From <Link Search>:

1 Select the file type ( : audio/ : video).[ ] [ ]

2 Select the tag type to display a list of contents

that contains the same tag as the track/file

currently being played, then select the item.

From <Folder List>:

Select the folder, then the item in the selected

folder.

Selecting a folder/track on the list

1 Display the folder/track list.

On the source control screen, touch as follows:

2 Select the list type.

3 Select the desired track.

• Repeat the procedure until you select the desired

track.

• For details about the list operation, see

page 11.

From <Category List>:

1 Select the file type ( : audio/ : video).[ ] [ ]

2 Select a category, then the item in the selected

category.

USB

USBUSB

Playback operations

Playback information and key operation

• For playback information, see “Source control screen”

on page 9.

• For key operations on the touch panel, see “Common

operation keys on source control screen” on

page 10.

• All tracks in the USB device will be played repeatedly

until you change the source or disconnect the USB

device.

Additional keys operations: Touching the operation

keys performs the following actions.

[USB DEVICE

CHANGE]*

Switches to another USB device when

two USB devices are connected.

* Only for DMX7018BT/DMX7018BTM/DMX718WBT/DMX718WBTM.

16 ENGLISH

iPod/iPhone

iPod/iPhoneiPod/iPhone

Connecting an iPod/iPhone

• For playable iPod/iPhone types and other

information, see page 55.

• You cannot watch video.

Wired connection

Rear panel

iPod/iPhone (commercially available)

USB Audio cable for iPod/iPhone: KCA-iP103

(optional accessory)

• For DMX7018BT/DMX7018BTM/DMX718WBT/

DMX718WBTM: You cannot connect two iPod/

iPhone at the same time.

Bluetooth connection

Pair the iPod/iPhone with this unit via Bluetooth.

(Page 26)

Playback operations

Playback information and key operation

• For playback information, see “Source control screen”

on page 9.

• For key operations on the touch panel, see “Common

operation keys on source control screen” on

page 10.

Selecting an audio file from the menu

1 Display the list.

On the source control screen, touch as follows:

2 Select the list type.

3 Select the desired track.

• Repeat the procedure until you select the desired

track.

• For details about the list operation, see

page 11.

From <Category List>:

Select a category, then the item in the selected

category.

• Available categories differ depending on the type

of iPod/iPhone.

From <Link Search>:

Select the tag type to display a list of contents that

contain the same tag as the track/file currently

being played, then select the item.

17ENGLISH

Connecting a smartphone

Android™ device

(commercially available)

iPhone (commercially

available)

USB cable (commercially available)

Rear panel

USB Audio cable for iPod/iPhone:

KCA-iP103 (optional accessory)

• When the smartphone is connected to the unit and

“WebLink” is selected as the source, a confirmation

message to communicate with each other appears

on the smartphone. Touch to establish [Allow]

connection, or to cancel the connection.[Ignore]

• You can check the connection status on the

WebLink™ screen on your smartphone.

Start playback

1 Select “WebLink” as the source.

2 Operate on the unit to select App.

• On the “WebLink” source screen, you can also

operate on the touch panel as follows:

[ ] • Displays the main menu of the

“WebLink” source screen.

• Exits the current App.

[ ] • Returns to the previous screen.

• Exits the current App.

3 Operate on your smartphone.

• When you are asked to communicate between

your smartphone and the unit, touch to [Allow]

proceed.

• If App does not start while using , start “WebLink”

the App on your smartphone.

Switching to the App screen while listening

to the another source

You can display the App screen while listening to the

other source.

DDX7018BT

DDX7018BTM

DMX7018BT

DMX7018BTM

DDX718WBT

DDX718WBTM

DMX718WBT

DMX718WBTM

Apps—WebLink™

Apps—WebLink™Apps—WebLink™

You can display and control the App on the unit

while your smartphone is connected to the USB input

terminal.

Preparation: Be sure to ground the PRK SW lead.

(Pages 49 – 52)

Available Apps

You can use the following Apps on this unit. Install the

WebLink™ App on your smartphone beforehand.

WebLink™

WebLink™ enables you to use the following Apps with

the unit.

• Media Player

• Yelp

• YouTube

• OpenWeatherMap

For DMX7018 T/DMX7018 TM/DMX718W T/B B B

DMX718W TMB

To use WebLink™ App on iPhone, connect the

iPhone to USB1 input terminal.

• WebLink™ App does not work on iPhone

connected to USB2 input terminal.

18 ENGLISH

Listening to the radio

Playback information on the source control

screen

99.1MHz

PS Name

80.0MHz

90.0MHz

99.1MHz

E.g. Radio source control screen for DDX7018BT

1 Selects the band (AM/FM1/FM2/FM3)

2 Current band/preset no.

3 Changes the seek mode for [ ]/[ ]S T

• (Initial): Auto searchAUTO1

• : Tunes in preset stations one after AUTO2

another

• : Manual searchMANUAL

4 Frequency/PS name

5 Tuner reception operation keys (TI/MONO/PTY)*

6 Preset list

7 Operation keys*

Radio

RadioRadio

8 Indicators

• : Lights up when News Standby Reception NEWS

is activated.

• : Lights up when Network-Tracking Reception AF

is activated.

• : Lights up in white when receiving the traffic TI

information, and lights in orange when Traffic

Information Reception is on standby.

• : Lights up when Local Seek is activated.LO.S

• : Lights up when receiving a stereo broadcast.ST

• : Lights up when receiving stations in MONO

monaural forcibly.

• : Indicates the status of the Radio Data RDS

System station reception when the Network-

Tracking Reception is activated. (Page 21)

−Lights in white: Radio Data System station is

being received.

−Lights in orange: Radio ata System station is D

not being received.

• : Lights up when a Radio Data System station EON

is sending EON signals.

* See the following “Operation keys on source control screen”.

Operation keys on source control screen

• The appearance of the operation keys may differ,

however the similar operation keys have the same

operations.

• See also “Common operation keys on source control

screen” on page 10.

Touching the operation keys performs the following

actions:

[TI]* (For FM Radio Data System features)

Activates TI standby reception mode.

• When TI is activated, the unit is ready to

switch to traffic information if available.

The TI indicator lights up in white.

• If the TI indicator lights up in orange,

tune into a station providing Radio Data

System signals.

• The volume adjustment for traffic

information is automatically

memorized. The next time the unit

switches to traffic information, the

volume is set to the memorized level.

• To deactivate, touch again.[TI]

[MONO]* Activates monaural mode for better FM

reception (stereo effect will be lost).

• The MONO indicator lights up while

monaural mode is activated.

• To deactivate, touch again.[MONO]

[PTY]* (For FM Radio Data System features)

Enters PTY search mode.

1 Touch a PTY code.

2 Touch [Search] to search for.

If there is a station broadcasting a

program of the same PTY code as you

have selected, that station is tuned in.

• You can set language displayed for the

PTY search on the <RADIO SETUP>

screen. (Page 21)

* Appears only when FM is selected as the source.

19ENGLISH

Radio

RadioRadio

Storing preset stations in the memory

You can preset 18 stations for FM and 6 stations for

AM.

Automatic presetting — AME (Auto

Memory)

On the source control screen, touch as follows:

A confirmation message appears. Touch .[Yes]

The local stations with the strongest signals are found

and stored automatically.

Manual presetting

1 Select the band, then tune in to a station

you want to store.

• See “Playback information on the source control

screen” on the page 19 for details.

2 Select a preset number to store into.

99.1MHz

PS Name

80.0MHz

90.0MHz

99.1MHz

(Hold)

The station selected in step 1 is stored into the

preset number you have selected.

[ ] Attenuates the sound.

• To restore the sound, touch the button

again, or adjust the volume.

[S T]/[ ] Searches for a station.

• The search method differs according

to the selected seek mode.

[AME] Presets stations automatically.

[ ] Displays the screen.<RADIO SETUP>

Selecting a preset station

Select the band ( ), then select a preset 1

station ( 2).

99.1MHz

PS Name

80.0MHz

90.0MHz

99.1MHz

20 ENGLISH

Radio

RadioRadio

Settings for tuner reception

1 Display the <RADIO SETUP> screen.

On the source control screen, touch as follows:

2 Make the settings.

[NEWS]*1

• to : Activates New Standby 00min 90min

Reception by selecting the period of time to

disable the interruption. The NEWS indicator

lights up.

• (Initial): Deactivates the function.OFF

[AF]

When driving in an area where FM reception is not

sufficient enough, this unit automatically tunes in

to another FM Radio Data System station of the

same network with stronger signals— Network-

Tracking Reception (AF: Alternative Frequencies).

• : Switches to another station. The program ON

may differ from the one currently received.*2

• (Initial): Deactivates the function.OFF

[Regional]

When driving in an area where FM reception is not

sufficient enough, this unit automatically tunes in

to another FM Radio Data System station of the

same program with stronger signals— Network-

Tracking Reception (Regional).

• : Switches to another station broadcasting the ON

same program.*2

• (Initial): Deactivates the function.OFF

[LO.S]

You can tune in FM stations only with strong

signals—Local Seek.

• : Tunes in only to FM stations with sufficient ON

signal strength. The LO.S indicator lights up.

• (Initial): Deactivates the function.OFF

[Auto TP Seek]

When traffic information station reception is poor,

the unit automatically searches for another station

that can be received better—Auto TP Seek.

• (Initial): Automatically searches for a station ON

with better reception for traffic information if the

current reception of current station is poor.

• : Deactivates the function.OFF

[Language Select]

Select the language to display for PTY search.

• (Initial)British English (en) /Espanol (es)/

Francais (fr)/Nederlands (nl)/Norsk (no)/

Portugues (pt)/Svenska (sv)/Deutsch (de)

To close the setting window, touch .[Close]

[Aerial Control]*3

• (Initial): Keeps the antenna extended even ON

when is not selected as the current “Radio”

source.

• : Stores the antenna automatically when OFF

the source is changed from to another “Radio”

source.

*1 The volume adjustment for Traffic Information is automatically

memorized. The next time the unit switches to Traffic

Information, the volume is set to the previous level.

*2 The RDS indicator lights up when the Network-Tracking

Reception is activated.

–Lights in white: Radio Data System station is being received.

–Lights in orange: Radio ata System station is not being D

received.

*3 Only for DDX718WBT/DMX718WBT.

21ENGLISH

Install the latest version of the Spotify application on

your smartphone.

• For Android devices: Search for “Spotify” in Google

Play to find and install the most recent version.

• For iPhone/iPod touch: Search for “Spotify” in the

Apple iTunes App Store to find and install the most

recent version.

Connecting the device

For Android devices

Pair the Android device with this unit via Bluetooth.

(Page 26)

For iPhone/iPod touch

• Via USB input terminal: Connect iPhone/iPod touch

with the cable KCA-iP103 (optional accessory).

(Page 17)

• Via Bluetooth: Pair the iPhone/iPod touch with this

unit. (Page 26)

Spotify

SpotifySpotify

With Spotify, your music is everywhere. Working out,

partying or relaxing, the right music is always at your

fingertips. There are millions of songs on Spotify—from

old favorites to the latest hits. Just choose the music

you love, or let Spotify surprise you.

You can stream Spotify from iPhone/iPod touch or

Android devices.

• Because Spotify is a third-party service, the

specifications are subject to change without

prior notice. Accordingly, compatibility may be

impaired or some or all of the services may become

unavailable.

• Some functions of Spotify cannot be operated from

this unit.

• For issues using the application, contact Spotify at

<www.spotify.com>.

Preparation

Installing the application

Your smartphone must has built in Bluetooth and the

following profiles must be supported:

• SPP (Serial Port Profile)

• A2DP (Advanced Audio Distribution Profile)

Establish an Internet connection using LTE, 3G, EDGE,

or Wi-Fi.

Ensure you are logged in to your smartphone

application. If you do not have a Spotify account, you

can create one for free from your smartphone or at

<www.spotify.com>.

Playback operations

Playback information and key operation

Spotify

E.g. Spotify source control screen for DDX7018BT

You can also operate Spotify with a remote controller,

RC-DV340*1.

You can only control play, pause and skip with the

remote controller.

1 Playing time

2 Picture data

3 Thumb up/down and repeat/shuffle playback

mode keys*2

4 Track information

• Touching [<] scrolls the text if not all of the text

is shown.

5 Operation keys*2

*1 For DMX7018BT Australian/New Zealand models/DM

Australian/New Zealand models: Purchase optional rem

controller, KNA-RCDV331.

*2 See “Operation keys on source control screen” on page

22 ENGLISH

Operation keys on source control screen

• The appearance of the operation keys may differ,

however the similar operation keys have the same

operations.

• See also “Common operation keys on source control

screen” on page 10.

Touching the operation keys performs the following

actions:

[ ]*1 Thumbs down to the current track and

skips to the next track.

[ ]*1 Registers the current track as a favorite.

[ ]*2 *3 Activates ( )/deactivates ( )

shuffle playback mode.

[ ]*2 Selects repeat playback mode

( : repeat one*3/ ALL: repeat all/

: repeat off).

[ ] Displays the Spotify menu screen.

[ ] Creates a new station (Start Radio).

[ ] ]*2 *3 [ Selects a track.

[ ][ ] Starts (I W)/pauses ( ) playback.

[ ]Saves the current track/artist/album to

<Your Music> <Your Library> or .

*1 Not available for tracks in a playlist.

*2 Not available for tracks in the Radio.

*3 Available only for premium account users.

Spotify

SpotifySpotify

Creating your station (Start Radio)

Start Radio is to start a radio channel based on the

currently played track.

Create your station.

On the source control screen, touch as follows:

Station is created and playback starts automatically.

• You can personalize your station using thumb up

( ) or thumb down ( ).[ ] [ ]

–Personalizing stations may not be available

depending on the track.

Selecting a track

1 Display the Spotify menu screen.

On the source control screen, touch as follows:

2 Select the list type, then select a desired

item.

• The list types displayed differ depending on the

information sent from Spotify.

Other External

Other External Other External

Components

ComponentsComponents

View camera

Install the view camera (separately purchased) in the

appropriate position according to the instructions

supplied with the view camera.

• You can use both rear view camera and front view

camera.

Connecting a view camera

See page 48 for more information for connection

terminals.

• To use the rear view camera, a reverse lead (REVERSE)

connection is required. (Pages 49 – 52)

Using the view camera

• For view camera settings, see “Camera settings” on

page 40.

To display the rear view camera screen

The rear view camera screen is displayed by shifting

the gear to the reverse (R) position when [R-CAM

Interruption] [ON] <Camera> is set to on the screen.

(Page 40)

• A caution message appears on the screen. To

remove the caution message, touch the screen.

23ENGLISH

You can also display the picture from the rear view

camera manually without shifting the gear to the

reverse (R) position.

On the monitor panel:

DDX7018BT

DDX7018BTM

DMX7018BT

DMX7018BTM

DDX718WBT

DDX718WBTM

DMX718WBT

DMX718WBTM

On the pop-up short-cut menu: Touch as follows (only

for ):DDX7018 T/DDX7018 TMB B

To display the front view camera screen

• Set [Front Camera] [ON] <Camera> to on the

screen beforehand. (Page 41)

While the rear camera screen is displayed, touch the

area shown below.

• Each time you touch the area, the screen is switched

between rear view camera and front view camera.

Other External Components

Other External ComponentsOther External Components

To exit the camera screen

Press on the monitor panel or touch the area HOME

shown below.

AV-IN

Connecting an external component

See page 48 for connection terminals.

Starting playback

1 Select “AV-IN” as the source.

On the Home screen, touch as follows:

2 Turn on the connected component and

start playing the source.

• For playback information, see “Source control

screen” on page 9.

Watching TV

Connecting a TV tuner box

Connect TV tuner box to the audio/video input (AV-IN)

terminal and TV tuner remote control output (REMO

OUT) terminal. (Page 48)

Displaying the TV screen

• Set [TV Tuner Control] [ON] <AV> to on the screen

beforehand. (Page 37)

1 Select “TV” as the source.

On the Home screen, touch as follows:

2 Turn on the TV.

24 ENGLISH

Other External Components

Other External ComponentsOther External Components

Playback information and key operation

E.g. TV screen for DDX7018BT

1 Hides the operation buttons on the screen while

video is played.

2 Operation keys*

* See the following “Operation keys on source control screen”.

Operation keys on source control screen

• The appearance of the operation keys may differ,

however the similar operation keys have the same

operations.

• See also “Common operation keys on source control

screen” on page 10.

Touching the operation keys performs the following

actions:

[CH ]/[CH ]J K Selects the channel.

Using the external navigation unit

You can connect a navigation unit (KNA-G630: optional

accessory) to the navigation input terminal so that you

can view the navigation screen. (Page 48)

• The navigation guidance comes out of the front

speakers even when you are listening to an audio

source.

Viewing the navigation screen

• For navigation settings, see “Navigation settings” on

page 42.

Select “NAV” as the source.

On the Home screen, touch as follows:

• While the navigation screen is displayed, the touch

panel operations are available only for navigation.

To exit the navigation screen

DDX7018BT

DDX7018BTM

DMX7018BT

DMX7018BTM

DDX718WBT

DDX718WBTM

DMX718WBT

DMX718WBTM

Switching the screen between the

navigation and current source

(Only for DMX7018BT/DMX7018BTM)

25ENGLISH

26 ENGLISH

Registering a new Bluetooth device

Pairing allows Bluetooth devices to communicate with

each other.

• The pairing method differs depending on the

Bluetooth version of the device.

–For devices with Bluetooth 2.1:

You can pair the device and the unit using SSP

(Secure Simple Pairing) which only requires

confirmation.

–For devices with Bluetooth 2.0:

You need to enter a PIN code both on the device

and the unit for pairing.

• Once connection is established, it is registered in the

unit even if you reset the unit. Up to 10 devices can

be registered in total.

• Two Bluetooth devices for Bluetooth phone and one

for Bluetooth audio can be connected at a time.

• To use the Bluetooth function, you need to turn on

the Bluetooth function of the device.

Auto pairing

When is set to on the <Auto Pairing> [ON] <TEL

SETUP> screen, iOS (such as iPhone) devices are

automatically paired when connected via USB.

(Page 32)

Bluetooth®

Bluetooth®Bluetooth®

Information

Bluetooth is a short-range wireless radio

communication technology for mobile devices such as

mobile phones, portable PCs and other devices.

Bluetooth devices can be connected without cables

and communicate with each other.

Note

• While driving, do not perform complicated

operations such as dialing numbers, using

the phonebook, etc. When you perform these

operations, stop your car in a safe place.

• Some Bluetooth devices may not connect to this unit

depending on the Bluetooth version of the device.

• This unit may not work for some Bluetooth devices.

• Connecting conditions may vary depending on your

environment.

• For some Bluetooth devices, the device is

disconnected when the unit is turned off.

• If your mobile phone supports PBAP (Phone Book

Access Profile), you can display the following items

on the touch panel when the mobile phone is

connected.

–Phonebook: up to 1 000 entries

–Dialed calls, received calls, and missed calls (up to

50 entries in total)

Preparation

• Connect and install the microphone beforehand. For

details, see pages 49 – 52.

For DDX7018BT/DMX7018BT:

–A built-in microphone is equipped with this unit.

You can also connect an external microphone to

the unit. If you are looking for an external Bluetooth

microphone, please contact the store where you

bought the product.

–Select a microphone to use (built-in or external)

via on the screen [MIC SETUP] <Bluetooth>

beforehand. (Page 42)

• Set [Bluetooth] [ON] <Bluetooth> to on the screen.

(Page 42)

Connection

When you connect a Bluetooth device to the unit for

the first time:

1 Register the device by pairing the unit and the

device.

2 Connect the device to the unit. (Page 28)

27ENGLISH

Registering a Bluetooth device

1 Search for the unit (“DDX***” or

“DMX***”) from your Bluetooth device

and operate the device to register.

For a Bluetooth device compatible with SSP

(Bluetooth 2.1):

Confirm the request both on the device and the

unit.

On the device:

On the unit:

• Touch [No] to reject the request.

For a Bluetooth device compatible with

Bluetooth 2.0:

Select the unit (“DDX***” or “DMX***”) on your

Bluetooth device.

• If a PIN code is required, enter the PIN code

shown on the screen (initial: “0000”).

To change PIN code, see page 28.

2 Determine usage as a hands free device

(1 2), then touch [Close] ( ).

[Hands Free1]/

[Hands Free2]

Select hands free number to

use as the hands free device.

[No Connection.] Select this when you do not

want to use as the hands free

device.

3 When your Bluetooth device is compatible

with A2DP or SPP: Determine usage as

an audio player or a device with Apps

installed.

[Yes] Select to use the device as an audio player.

[No] Select this when you do not want to use

the Bluetooth device as an audio player.

Bluetooth®

Bluetooth®Bluetooth®

4 When your Bluetooth device is compatible

with PBAP: Select whether to transfer the

phonebook of your Bluetooth device to

the unit or not.

[Yes] Select to transfer the phonebook from

your Bluetooth device.

[No] Select this when you do not want to

transfer the phonebook.

28 ENGLISH

Bluetooth®

Bluetooth®Bluetooth®

Changing the PIN code

1 Display the <Change PIN Code> screen.

On the Home screen, touch as follows:

Then, on the screen, touch .<SETUP> [Bluetooth]

On the screen, touch <Bluetooth Setup> [PIN

Code].

2 Enter the PIN code ( ), then confirm the 1

entry ( 2).

• To clear the last entry, touch .[BS]

3 Select the usage of the device ( ), then 1

touch [Close] ( 2).

Each time you touch the selection, the usage is

selected (“ ” appears) or deselected (“ ”

disappears). Select to connect and deselect to

disconnect the device.

[TEL (HFP)1]/

[TEL (HFP)2]

Select to use as the hands free

device.

[Audio (A2DP)/

App (SPP)]

Select to use as the audio

player or device with Apps

installed.

To delete the registered Bluetooth device: Touch

[Delete] in step 2, select devices to delete, then touch

[Delete]. A confirmation message appears. Touch

[Yes].

• To select all devices, touch [ All].

• To deselect all selected devices, touch .[ All]

Connecting/disconnecting a registered

Bluetooth device

1 Display the <Select Device> screen.

On the Home screen, touch as follows:

Then, on the screen, touch .<SETUP> [Bluetooth]

On the screen, touch <Bluetooth Setup> [Select

Device].

2 Select the device you want to connect/

disconnect.

The icons beside the registered device indicate the

following:

• / : Connected as a mobile phone.

• : Connected as an audio player.

29ENGLISH

Bluetooth mobile phone

When a call comes in...

Touching the operation keys performs the following

actions:

[ ] Answers a call.

[ ] Rejects a call.

[Speech

Quality]

Displays the <Speech Quality adjust>

screen.

• : Adjusts the Microphone Level

microphone volume level. (–10 to 10,

initial: 0)

• : Adjusts the echo Echo Cancel Level

volume level. (OFF, –5 to 5, Initial: 0)

• : Adjusts the Noise Reduction Level

noise reduction volume. (OFF, –5 to 5,

Initial: 0)

• Call information is displayed if acquired.

• Phone operation is not available while the picture

from the view camera is displayed.

Changing the device name of the unit

displayed on the paired device

1 Display the <Change Device Name>

screen.

On the Home screen, touch as follows:

Then, on the screen, touch .<SETUP> [Bluetooth]

On the screen, touch <Bluetooth Setup> [Device

Name].

2 Enter the device name ( ), then confirm 1

the entry ( 2).

• To clear the last entry, touch .[BS]

• To move the entry position, touch .[ ]/[ ]H I

During a call...

Touching the operation keys performs the following

actions:

[ ] Ends a call.

[ ] Mutes the volume of the microphone.

[ ]/

[ ]

Switches between hands free mode

and phone mode.

[DTMF] Enters DTMF (Dual Tone Multi

Frequency), then sends text using the

keypad.

[Speech

Quality]

Displays the <Speech Quality adjust>

screen.

• See the left column for details.

Bluetooth®

Bluetooth®Bluetooth®

30 ENGLISH

C When item is selected in step 2:5

Say the name of the person you want to

call.

• You can also make voice dialing by pressing and

holding the on the monitor panel.VOICE

• Available only when the connected mobile

phone has a voice recognition system.

• If the unit cannot find the target, “Press [Restart]

to restart the voice recognition process.” appears.

Touch , then say the name again.[Restart]

• To cancel voice dialing, touch .[Stop]

Switching between two connected devices

You can change the device to use when two devices

are connected.

On the phone control screen:

The active device is highlighted.

Bluetooth®

Bluetooth®Bluetooth®

Making a call

1 Display the phone control screen.

On the Home screen, touch as follows:

2 Select a method to make a call.

1 From the call history* (missed calls/received

calls/dialed calls)

2 From the phonebook*

3 From the preset list (Page 31)

4 Use direct number entry

5 Use voice dialing

3 Select a contact to make a call.

A When item , or is selected in step 2:1 2 3

• If the selected contact has several phone

numbers, the phone number list is displayed.

Select a phone number to make a call.

To use alphabet search in the phonebook

1 Touch [ A-Z ].

2 Touch the first letter you want to search for on

the keypad.

To search for a number, touch .[1]

3 Select a contact you want to call from the list.

• You can select a first name or last name to use

when sorting the list in alphabetical order on the

<TEL SETUP> screen. (Page 32)

B When item is selected in step 2:4

Enter the phone number ( ), then make a 1

call (2).

• To enter “+”, touch and hold .[0/+]

• To clear the last entry, touch .[BS]

* Applicable only for mobile phone compatible with PBAP (Phone

Book Access Profile).

31ENGLISH

Bluetooth®

Bluetooth®Bluetooth®

Presetting phone numbers

You can preset up to eight phone numbers.

1 Display the <Edit Preset Dial> screen.

On the Home screen, touch as follows:

Then, on the phone control screen, touch as

follows:

[ [Edit] ] →

2 Select a position to store into.

3 Select a method to add a phone number

to preset list and register the number to

the preset list ( 1 2), then touch [Close] ( ).

[Add

number from

phonebook]

Select a phone number from

the phonebook.

[Add number

direct]

Enter a phone number on the

direct number entry screen,

then touch to add to the [Set]

preset list.

• To display the preset list, touch [ ] on the phone

control screen.

To delete a phone number from the preset list:

Select the phone number to delete on the <Edit

Preset Dial> [Delete] screen, then touch in step 3.

To delete all phone numbers from the preset list:

Touch on the screen [Delete all] <Edit Preset Dial>

in step 2.

Editing phonebook

To transfer the phonebook

If the connected Bluetooth mobile phone is

compatible with Phone Book Access Profile (PBAP),

you can transfer the phonebook of the mobile phone

to the unit.

1 Display the phone control screen.

On the Home screen, touch as follows:

2 Start phonebook data transmission.

To delete contact from the phonebook: Touch

[ ] in step 2 ( ), select devices to delete, then 2

touch . A confirmation message appears. [Delete]

Touch .[Yes]

• To select all devices, touch .[ All]

• To deselect all selected devices, touch .[ All]

• Touch [ A-Z ] to search the contact by initial.

32 ENGLISH

Bluetooth®

Bluetooth®Bluetooth®

Bluetooth audio player

Bluetooth

E.g. Bluetooth source control screen for

DDX7018BT

1 Displays/hides other available operation keys*1

2 Artwork (Shown if the track contains artwork)

3 Connected device name

4 Repeat/random playback mode keys*1

5 Signal strength and battery level

(Appears only when the information is acquired

from the device.)

6 Tag data*2 (current track title/artist name/album

title)

• Pressing [<] scrolls the text if not all of the text is

shown.

7 Operation keys*1

*1 See “Common operation keys on source control screen” on

page 10.

*2 Available only for devices compatible with AVRCP 1.3.

Playback information and key operation

• For playback information, see “Source control

screen”on page 9.

• For key operations on the touch panel, see “Common

operation keys on source control screen” on

page 10.

Additional keys operations: Touching the operation

keys performs the following actions.

[BT DEVICE

CHANGE]

Switches to another Bluetooth audio

player.

Selecting a track from the list

1 Display the music list.

On the source control screen, touch as follows:

2 Select the folder, then the item in the

selected folder.

• For details about the list operation, see

page 11.

Bluetooth mobile phone settings

You can change various settings for using Bluetooth

mobile phones on the screen.<TEL SETUP>

1 Display the <TEL SETUP> screen.

On the Home screen, touch as follows:

Then, on the screen, touch .<SETUP> [Bluetooth]

On the screen, touch <Bluetooth Setup> [TEL

SETUP].

2 Make the settings.

33ENGLISH

Bluetooth®

Bluetooth®Bluetooth®

Select the speakers used for Bluetooth mobile

phones.

• : Front speakers only.Front

• (Initial): All speakers.All

• (in 5 second steps): The unit answers the 1 – 30

incoming calls automatically. Set the calling ring

time (seconds).

• (Initial): The unit does not answer the calls OFF

automatically. Answer the calls manually.

• (Initial): Establishes pairing automatically ON

with the iOS device (such as iPhone) connected

via USB. (Auto pairing may not work for some

devices depending on the iOS version.)

• : Cancels.OFF

Select a first name or last name to use when sorting

the list in alphabetical order.

• : Sorts the list in the order of first name.First

• (Initial): Sorts the list in the order of last Last

name.

Settings

SettingsSettings

Audio settings

1 Display the <Audio> screen.

On the Home screen, touch as follows:

2 Select a setting to change.

E.g. Audio settings screen for DDX7018BT

You cannot change the screen in the <Audio>

following situations:

• When the AV source is turned off

• When the Bluetooth phone is used (making or

receiving a call, during a call, or while voice dialing)

• During navigation guidance

Preparation:

Before making the adjustment for , <Speaker/X’over>

select the appropriate crossover network mode

according to the speaker system (2-way speaker

system or 3-way speaker system).

1 Put the unit in standby.

On the Home screen, touch as follows:

Then, on the source/option selection screen, touch

[STANDBY].

2 Display the <X’over Network> screen.

On the monitor panel, press the following buttons

at the same time:

DDX7018BT

DDX7018BTM

DDX718WBT

DDX718WBTM

DMX718WBT

DMX718WBTM

DMX7018BT

DMX7018BTM

3 Select the crossover network mode.

[2way] Select this when 2-way system

speakers are used (front/rear).

[3way] Select this when 3-way system

speakers are used (tweeter/mid

range/woofer).

A confirmation message appears. Touch .[Yes]

34 ENGLISH

Settings

SettingsSettings

Setting the speakers and crossover

frequency

1 Select a car type ( ), select a speaker 1

(2) (front speakers, rear speakers, or

subwoofer) to set, then location* and

speaker/tweeter size (3) of the selected

speaker.

A selection window appears for each setting. Select

an item, then touch to close the window.[Close]

Comfort

4 inch

Car Type

Speaker

Door

Location

Medium

Tweeter

X’over

Speaker Select

• Repeat steps 2 3 and to set all speakers.

• Adjustable items vary depending on the selected

speaker type.

• When a speaker is not connected, select .[None]

• When setting the front speakers, also select the

speaker size for .<Tweeter>

2 Touch [X’over] to display the <X’over>

screen.

3 Select the speaker type ( ), then adjust 1

the crossover frequency (2) of the

selected speaker.

X’over

100 Hz

HPF FREQ

-6 dB/Oct

Slope

0 dB

Gain

-1 dB

TW Gain

SubwooferRearFront

• Adjustable items vary depending on the selected

speaker type/speaker size/crossover settings.

Adjusts the crossover frequency for the front or rear

speakers (high pass filter).

Adjusts the crossover frequency for the speaker

(low pass filter).

<Slope>

Adjusts the crossover slope.

<Gain>

Adjusts the output volume of the selected speaker.

Adjusts the output volume of the tweeter.

Selects the phase for the speaker.

* Speaker location selection is available only when <X’over

Network> is set to [2way].

The following adjustments are memorized for each

source until you adjust the sound again. If the source

is a disc, the adjustments are stored for each of the

following categories.

• DVD/VCD

• CD

• Audio/video files (Page 53)

You cannot adjust the sound when the unit is in

standby.

Selecting a preset sound mode

1 Display the preset sound modes.

2 Select a preset sound mode.

• Pops/Easy/Top40/Jazz/Powerful/Rock/Flat

(Initial)/iPod/User1/User2/User3/User4

Graphic Equalizer ALL SRC

iPod

Flat

Pops

iPod

Easy

User1

Top40

User2

Jazz

User3

Powerful

User4

Rock

To hide the preset sound modes: [ Touch ].

35ENGLISH

Settings

SettingsSettings

Store your own sound adjustments

1 Select a preset sound mode.

2 Select a band ( ) and adjust the level ( ), 1 2

then adjust the sound ( 3).

Graphic Equalizer ALL SRC

Preset Select Bass EXT SW Level

USB

Initialise Memory ON OFFOFF

Adjust the sound as follows:

Activates/deactivates bass.

• / (Initial)ON OFF

Adjusts the subwoofer level.*

• to (Initial: )–50 +10 0

3 Repeat step 2 to adjust the level of other

bands.

4 Touch [Memory] to store adjustment.

A user selection window appears. Select from

[User1] [User4] to to store your adjustment, then

touch to close the window.[Close]

• To apply the adjusted equalizer to all playback

source, touch , then touch to [ALL SRC] [OK]

confirm.

• To clear the adjustment, touch .[Initialise]

* Not adjustable when <None> is selected for subwoofer on the

<Speaker Select> screen. (Page 34)

You can adjust the sound effects according to your

listening position. You can also localize the sound

image in front of the selected seat.

Setting the listening position

Touch [Listening Position] ( ), then select 1

the listening position ([Front L], [Front R],

[Front All]*, or [All]) (

2).

Front FocusListening Position

Front L

Front All

Front R

All

Adjust

Position/DTA

* [Front All] is selectable only when <X’over Network> is set to

[2way].

Adjusting the Digital Time Alignment (DTA)

Make fine adjustments to the delay time of the speaker

output to create a more suitable environment for your

car.

1 Touch [Adjust] on the <Position/DTA>

screen to display the DTA adjustment

screen.

2 Touch [Delay] ( ), then adjust the Digital 1

Time Alignment (DTA) value ( 2) for each

speaker.

Front L

0 feet

0 ms

Rear L

0 feet

0 ms

0 feet

0 ms

Front R

Rear R

0 feet

0 ms

Initialise

Level

Delay

Position/DTA

Subwoofer

0 feet

0 ms

• To determine the adjustment value, see

“Determining the value for <Position/DTA>

adjustment” on page 36.

3 Touch [Level] ( ), then adjust the output 1

volume ( 2) for each speaker.

0 dB

Tweeter

0 dB

Front L

0 dB

Rear L

0 dB

Front R

0 dB

Rear R

0 dB

Subwoofer

Initialise

Level

Delay

Position/DTA

To initialize the setting value: [Initialise] Touch .

36 ENGLISH

Settings

SettingsSettings

Localizing the sound image—Front Focus

1 Touch [Front Focus] ( ), select the 1

listening position (2) to set as the front

position, then touch [Adjust] (3).

Front FocusListening Position

Front L

Front All

Priority L

All

Priority L

Front R

Front All

Priority R

All

Priority R

Adjust

Position/DTA

• When you are sitting on the (front [Front All]

seats) or (front and rear seats) position, select [All]

left ( ) or right ( ) to specify “Priority L” “Priority R”

the position to localize the sound image.

2 Touch [Delay] ( ), then adjust the sound 1

image (2) precisely.

Initialise

Sound Image LR(Front)

Sound Image LR(Rear)

Size of the Virtual Sound Field

Subwoofer Delay

Level

Delay

Front Focus Adjust

0.00ms

0.00ms 0.00ms

[Sound Image LR (Front)]

Adjusts the sound image to be localized set on the

front position.

[Sound Image LR (Rear)]

Adjusts the sound image to be localized set on the

rear position.

[Size of the Virtual Sound Field]

Adjusts the virtual sound field to the desired field

size.

• If the sound image moves out of the front

position, adjust /[Sound Image LR (Front)]

[Sound Image LR (Rear)].

[Subwoofer Delay]

Adjusts the delay time of the subwoofer sound.

3 Touch [Level] ( ), then adjust the output 1

volume (2) for each speaker.

0 dB

Tweeter

0 dB

Front L

0 dB

Rear L

0 dB

Front R

0 dB

Rear R

0 dB

Subwoofer

Initialise

Level

Delay

Front Focus Adjust

To initialize the setting value: [Initialise] Touch .

Determining the value for <Position/DTA>

adjustment

If you specify the distance from the center of the

currently set listening position to every speaker, the

delay time will be automatically computed and set.

1 Determine the center of the currently set

listening position as the reference point.

2 Measure the distances from the reference point

to the speakers.

3 Calculate the differences between the distance of

the furthest speaker and other speakers.

4 3 Set the DTA value calculated in step for

individual speakers.

5 Adjust gain for individual speakers.

E.g. When is selected as the listening [Front All]

position

+90 cm

60 cm

70 cm

+80 cm150 cm

+0 cm

37ENGLISH

Settings

SettingsSettings

Touch / / / or drag the mark to adjust.[ ]J[ ]K[ ]H[ ]I

<Fader>

Adjusts the front and rear speaker output balance.

When using a two-speaker system, set the fader to the

center ( ).0

• to (Initial: )F15 R15 0

Adjusts the left and right speaker output balance.

• to (Initial: )L15 R15 0

To clear the adjustment: [Center] Touch .

Adjust and store the auto-adjustment volume level

for each source. The volume level will automatically

increase or decrease when you change the source.

If you have increased the volume first, then reduced

the volume using the Volume Offset, the sound

generated if you suddenly switch to another source

may be extremely loud.

• to (Initial: )–5 +5 0

To initialize the setting value: [Initialise] Touch .

Adjust the sound effect.

Selects the bass boost level.

• (Initial)/ / /OFF 1 2 3

Adjusts loudness. (The LOUD indicator lights up when

the loudness is adjusted.)

• (Initial)/ /OFF Low High

Reduces the driving noise by raising the bandwidth.

• (Initial)/OFF ON

<Space Enhancer>*

Virtually enhances the sound space using the Digital

Signal Processor (DSP) system. Select the enhance

level.

• (Initial)/ / /OFF Small Medium Large

Restores the sound lost due to audio compression to a

realistic sound.

• / (Initial)OFF ON

Virtually makes the sound more realistic using the

Digital Signal Processor (DSP) system. Select the sound

level.

• (Initial)/ / /OFF 1 2 3

Moves the localization of the sound image to the

lower or higher point. Select the height.

• (Initial)/ / /OFF Low Middle High

* You cannot change the setting when “Radio” is selected as the

source.

AV settings

Display the <AV> screen.

On the Home screen, touch as follows:

Then, on the screen, touch .<SETUP> [AV]

Bluetooth NavigationSpecial

AV Display Camera

User Interface

SETUP

Security

E.g. Setup screen for DDX7018BT

• : Enables control of TV operation on .ON “AV-IN”

• (Initial): Select this to use with OFF “AV-IN”

components other than TV Tuner.

38 ENGLISH

You can change the illumination color of the buttons

on the monitor panel.

Key Color

Adjust

User Scan

• You can also adjust the illumination color yourself.

Touch to display the illumination color [Adjust]

adjustment screen, then adjust the color. The

adjustment is saved in .[User]

• Selecting [Scan] changes the illumination color

gradually.

You can change the background design or color.

To change the background design:

*1 *2

Settings

SettingsSettings

Display settings

Display the <Display> screen.

On the Home screen, touch as follows:

Then, on the screen, touch .<SETUP> [Display]

• : Activates dimmer.ON

• : Deactivates dimmer.OFF

• (Initial): Dims the screen and button SYNC

illumination when you turn on the headlights.

–The ILLUMI lead connection is required.

(Pages 49 – 50)*

• : Activates or deactivates dimmer NAV-SYNC

according to the day/night display setting of the

external navigation unit.

• (Initial): Displays the clock while a video source ON

is playing.

• : Cancels.OFF

* Only for DDX7018BT/DDX7018BTM/DMX7018BT/DMX7018BTM.

To change the background color: Touch

[Background Color], then select the color on the

<Background Color> screen.

• You can select same color selected in <Key Color>

as the background color by touching [Sync Color

Settings].

• If [Scan] <Key Color> is selected in , user cannot

select .[Sync Color Settings]

*1 Selects background color in advance.

*2 Selects a loaded favorite image in advance.

Storing your favorite image for the

background

You can use your favorite image stored on the

connected USB device for the background.

• Connect the USB device on which the image is

stored beforehand.

• Use a JPEG/PNG/BMP file with a resolution of 800 x

480 pixels.

1 Touch [User1 Select] or [User2 Select] to

store the image for the <Background>

screen.

2 Select the folder, then the file for the

background image in the selected folder.

User Background Select

39ENGLISH

Settings

SettingsSettings

3 Rotate the image ( ) if necessary, then 1

confirm the selection (2).

A confirmation message appears. Touch [Enter]

to store the new image. (The existing image is

replaced with the new one.)

Select the viewing angle in relation to the monitor to

make the image on the screen easier to see.

• (Initial)/ / /0 –1 –2 –3

User interface settings

Display the <User Interface> screen.

On the Home screen, touch as follows:

Then, on the screen, touch .<SETUP> [User Interface]

Assign functions to the keys on the remote controller

of the steering wheel.

• This function is available only when your car is

equipped with the electrical steering remote

controller.

• You can only register/change the functions while

you are parked.

• If your steering remote controller is not compatible,

learning may not be completed and an error

message may appear.

1 When the unit is ready for learning, press

and hold a steering remote controller

button for about 2 seconds to register/

change.

• Refer to the message displayed to confirm

whether the unit ready before proceeding.

2 Select a function to assign to the selected

button.

3 Repeat steps 1 and 2 to register other

functions to other buttons.

4 Touch [Learning completed] to finish

procedure.

A confirmation message appears. Touch .[Yes]

• The unit can register/change all of the buttons’

functions at the same time. To do this, press all

buttons in turn and after pressing all of them, touch

[Learning completed] in step 2. However, new

functions cannot be learned after this operation.

• When changing the functions already learned, touch

the assigned function you want to change in step 2

and then touch to select the new function from the

function list.

• Confirm the contents of the settable functions in the

function list. You cannot edit the function list.

To initialize the setting: [Learning Touch

initialisation] in step 2.

• A confirmation message appears. Touch .[Yes]

–To cancel the initialization, touch .[No]

40 ENGLISH

Camera settings

Display the <Camera> screen.

On the Home screen, touch as follows:

Then, on the screen, touch .<SETUP> [Camera]

<R-CAM Interruption>

• : Displays the picture from the rear view camera ON

when you shift the gear to the reverse (R) position.

• (Initial): Select this when no camera is OFF

connected.

• (Initial): Displays the parking guidelines.ON

• : Hides the parking guidelines.OFF

Settings

SettingsSettings

<Clock>

Select the method to set the date and clock. For

details, see “Calendar/clock settings” on page 7.

<Time Zone>*2

Select the time zone for your area. For details, see

“Calendar/clock settings” on page 7.

<Clock Adjust>*2

Adjust the date and clock manually. For details, see

“Calendar/clock settings” on page 7.

(Only for DDX7018BTM/DMX7018BTM/

DDX718WBTM/DMX718WBTM)

• : Displays the prayer for driving safety, then plays ON

Quran.

• (Initial): Deactivates the function.OFF

<Travel Prayer for Safe Drive Volume>*3

(Only for DDX7018BTM/DMX7018BTM/

DDX718WBTM/DMX718WBTM)

Adjusts the sound volume of Quran.

*1 Available only when <X’over Network> is set to [2way].

*2 Available when [Clock] is set to [Manual].

*3 Available when [Travel Prayer for Safe Drive] is set to [ON].

<Beep>*1

• (Initial): Activates the key-touch tone.ON

• : Deactivates the key-touch tone.OFF

Select the text language used for on-screen

information. For details, see “Initial settings” on

page 6.

(Only for DDX7018BT/DDX7018BTM/DMX7018BT/

DMX7018BTM)

Adjust the touch positions of the buttons on the

screen.

Touch and hold the center of the marks at the lower

left ( ), then the upper right ( ) as instructed.1 2

(Hold)

• To reset the touch position, touch .[Reset]

• To cancel the current operation, touch .[Cancel]

41ENGLISH

Settings

SettingsSettings

Adjust the parking guidelines according to the size of

the car, parking space and so on.

When adjusting the parking guidelines, make sure to

use the parking brake to prevent the car from moving.

Touch one of the marks ( ), then adjust the 1

position of the selected mark ( ).2

Make sure that and are horizontally parallel, and A B

that and are the same length.C D

• Touch [Initialise] to set all the marks to the initial

default position. A confirmation message appears.

Touch . [Yes]

• : Select this when a front view camera is ON

connected.

• (Initial): Select this when no camera is OFF

connected.

• : Displays the picture from the front view camera ON

horizontally reversed.

• (Initial): Displays the picture from the front view OFF

camera as it is.

Special system settings

Display the <Special> screen.

On the Home screen, touch as follows:

Then, on the screen, touch .<SETUP> [Special]

<DEMO>

• (Initial): Activates the display demonstration.ON

• : Deactivates the display demonstration.OFF

(Only for DDX7018BT/DDX7018BTM/DMX7018BT/

DMX7018BTM)

Assign the function of the HOME on the monitor panel

when pressed and held.

• : Turns off the screen and audio.AV OFF

The screen and audio restores when receiving call,

inputs video signal from the rear view camera, etc.

• (Initial): Turns off the power.Complete OFF

• : Locks the Lock <Audio SETUP Memory>/<Audio

SETUP Recall>/<Audio SETUP Clear> settings.

– The items in the settings <Speaker/X’over>

cannot be adjusted when is selected.[Lock]

• : Unlocks the settings.Unlock

<Audio SETUP Memory>*

Memorizes the following audio settings:

• Fader/Balance

• Speaker/X’over

• Equalizer (Adjustment on user preset ( – [User1]

[User4])/Subwoofer level adjustment)

• Position/DTA

• Sound Effect

A confirmation message appears. Touch .[Yes]

<Audio SETUP Recall>*

Recall the settings memorized by <Audio SETUP

Memory>. A confirmation message appears. Touch

[Yes].

<Audio SETUP Clear>*

Clear the settings made on the screen. A <Audio>

confirmation message appears. Touch .[Yes]

Display the information of the software (such as serial

number, application version, system version, etc.). You

can update the software.

Show the Open Source Licenses.

Initialize all settings made on the unit. A confirmation

message appears. Touch .[Yes]

• The settings memorized on the <Audio SETUP

Memory> are not initialized.

* Available only when <SETUP Memory> is set to [Unloc

42 ENGLISH

Navigation settings

Display the <Navigation> screen.

On the Home screen, touch as follows:

Then, on the screen, touch .<SETUP> [Navigation]

Adjust the volume of the navigation guidance. ( to 0

40 24, Initial: )

Settings

SettingsSettings

Bluetooth settings

Display the <Bluetooth> screen.

On the Home screen, touch as follows:

Then, on the screen, touch .<SETUP> [Bluetooth]

• (Initial): Activates the Bluetooth function of the ON

unit.

• : Deactivates the Bluetooth function of the unit.OFF

Connect or disconnect the paired device. (Page 28)

Display/change the device name to be shown on the

Bluetooth device. (Page 29)

Change the PIN code of the unit. (Page 28)

Display the device address of the unit.

Configure the setting for using a Bluetooth mobile

phone. (Page 32)

(Only for DDX7018BT/DMX7018BT Southeast Asian

models/DMX7018BT Indonesian models)

Select the microphone to use for Bluetooth mobile

phone.

• (Initial): Select this when using built-in Built-in Mic

microphone.

• : Select this when using the external External Mic

microphone connected to the MIC terminal.

Security settings

Display the <Security> screen.

On the Home screen, touch as follows:

Then, on the screen, touch .<SETUP> [Security]

Clear the security code. (Page 7)

Change the security code. (Page 7)

43ENGLISH

Remote Controller

Remote Controller Remote Controller

• For DDX7018BT/DDX7018BTM/DMX7018BT

Southeast Asian models/DMX7018BT Indonesian

models/DMX7018BTM/DDX718WBT/

DDX718WBTM/DMX718WBT Southeast Asian

models/DMX718WBT Indonesian models/

DMX718WBTM: This unit can be operated using the

remote controller (RC-DV340) supplied with this unit.

• For DMX7018BT Australian/New Zealand

models/DMX718WBT Australian/New Zealand

models: Optional remote controller KNA-RCDV331

is designed for controlling this unit. Refer to the

instruction manual that comes with the remote

controller.

CAUTION

• Put the remote controller in a place where it will

not move during braking or other operations. A

dangerous situation could result if the remote

controller falls down and gets wedged under the

pedals while driving.

• Do not leave the battery near fire or under direct

sunlight. A fire, explosion or excessive heat

generation may result.

• Do not recharge, short, break up or heat the battery,

or place it in an open fire. Such actions may cause

the battery to leak fluid. If spilled fluid comes in

contact with your eyes or clothing, immediately rinse

with water and consult a physician.

• Place the battery out of reach of children. In the

unlikely event that a child swallows the battery,

immediately consult a physician.

Preparation

Battery installation

Use two “AAA”/“R03”-size batteries.

Insert the batteries with the + and – poles aligned

properly, following the illustration inside the case.

• Always insert batteries from – poles to avoid bending

the springs.

• If the remote controller operates only over shorter

distances or does not operate at all, it is possible that

the batteries are depleted. In such instances, replace

both batteries with new ones.

Remote controller mode switch

The functions operated from the remote controller

differ depending on the position of the mode switch.

DVD

T V

AUD

DVD

T V

NAV

AUD

• : Switch to this mode when controlling a AUD mode

selected source or tuner source, etc.

– When controlling a player that is not integrated in

the unit, select “AUD” mode.

• : Switch to this mode when playing DVDs DVD mode

or CDs etc. with the player integrated in this unit.

• : Not used.TV mode

• : Not used.NAV mode

• The position of the remote control mode switch is

indicated in the title of each mode, e.g., “AUD mode”.

Basic operations for RC-DV340 (supplied)

44 ENGLISH

Remote Controller

Remote ControllerRemote Controller

Common operations (AUD mode)

SRC • Selects the source.

• Hangs up the incoming/current call.

J K/ VOL Adjusts the volume level.

ATT Attenuates/restores the sound.

DISP/V.SEL Switches to the navigation screen.

ENTER Enters options.

Answers incoming calls.

FNC/PBC/

Switches the control screen.

MODE/TOP

Changes the aspect ratio.

• The aspect ratio changes each time

you press this key.

OPEN Adjusts the panel angle.

• The panel angle changes each time

you press this key.

DVD/VCD (DVD mode)*

J K H I/// Moves the cursor when displaying a

menu.

S T/Selects a track.

I W/Starts/pauses playback.

oStops and memorizes the point

where the disc stops.

0 – 9 • Specifies the number to search for

in direct search.

• : Fast forwards/backwards.1/2

– Fast forward/backward speed

changes each time you press this

key.

• : Slow forwards/backwards 4/5

during pause.

MODE/TOP

Shows the disc top menu.

FNC/PBC/

Shows the disc menu.

SUBTITLE Changes the subtitle language.

ZOOM Changes the zoom ratio.

• The zoom ratio changes each time

you press this key.

ANGLE Changes the picture angle.

• The picture angle changes each

time you press this key.

AUDIO Changes the voice language.

• The voice language changes each

time you press this key.

DIRECT Enters direct search mode.

CLEAR Deletes a character while in direct

search mode.

* Only for DDX7018BT/DDX7018BTM/DDX718WBT/DDX718WBTM.

Music Disc/Audio file/Video file (AUD m

AM –/FM + Selects a folder.

S T/Selects a track/file.

I W/Starts/pauses playback.

0 – 9 Specifies the number to search for in

direct search.

DIRECT Enters direct search mode.

Radio (AUD mode)

AM –/FM + Selects the band.

S T/Searches for stations.*

I W/Changes the seek mode (AUTO1,

AUTO2, MANUAL).

0 – 9 • Specifies preset number.

• Specifies the frequency of the

station to receive to search for in

direct search.

DIRECT Enters direct search mode.

* The search method differs according to the selected seek

45ENGLISH

Remote Controller

Remote ControllerRemote Controller

iPod/Android (AUD mode)

S T/Selects music/videos.

I W/Starts/pauses playback.

USB (AUD mode)

AM –/FM + Selects a folder.

S T/Selects a file.

I W/Starts/pauses playback.

Searching for an item directly

While listening to the radio or during disc playback,

you can search for a station frequency/chapter/title/

folder/file/track directly using the number buttons.

• To search for a track from the VCD menu, perform

during PBC playback.

1 Press DIRECT to enter the search mode.

• Each time you press , the item to search DIRECT

for changes.

2 Press a number button to select a desired

item (station frequency/chapter/title/

folder/file/track).

• To erase a misentry, press .CLEAR

3 Confirm the selection.

• For station frequency: Press / .S T

• For others: Press .ENTER

To exit the search mode: DIRECT Press .

Basic operations for KNA-RCDV331

(optionally purchased)

Common operations (AUD mode)

SRC • Selects the source.

• Hangs up the incoming/current

call.

VOL J K/Adjusts the volume level.

ATT Attenuates/restores the sound.

VOICE/FNC/

MENU/PBC

For discs/USB/iPod: Switches to the

current source control screen.

ENTER Enters options.

Answers incoming calls.

ROUTE M/

MODE/

TOP MENU

Changes the aspect ratio.

• The aspect ratio changes each

time you press this key.

VIEW/AVOUT Switches the AV source to be

output.

MAP DIR/OPEN Adjusts the panel angle.

• The panel angle changes each

time you press this key.

NAV/DISP Switches to the navigation screen.

ZOOM OUT/IN Not used for this unit.

2 ZONE Not used for this unit.

R.VOL Not used for this unit.

Music Disc/Audio file/Video file (AUD m

J K/FM+ / /AM− Selects a folder.

H S T I/ / / Selects a track/file.

POSITION/

IW Starts/pauses playback.

0 – 9 Specifies the number to search for

in direct search.

# BS/DIRECT Enters direct search mode.

46 ENGLISH

Remote Controller

Remote ControllerRemote Controller

Radio (AUD mode)

J K/FM+ / /AM− Selects the band.

H S T I/ / / Searches for stations.*

POSITION/

IW Changes the seek mode (AUTO1,

AUTO2, MANUAL).

0 – 9 • Specifies preset number.

• Specifies the frequency of the

station to receive to search for in

direct search.

# BS/DIRECT Enters direct search mode.

* The search method differs according to the selected seek mode.

iPod (AUD mode)

H S T I/ / / Selects music/videos.

POSITION/

IW Starts/pauses playback.

USB (AUD mode)

J K/FM+ / /AM− Selects a folder.

H S T I/ / / Selects a file.

POSITION/

IW Starts/pauses playback.

Installation and

Installation and Installation and

Connection

ConnectionConnection

WARNINGS

• DO NOT connect the ignition wire (red) and the

battery wire (yellow) to the car chassis (ground), you

may cause a short circuit, that in turn may start a fire.

• DO NOT cut out the fuse from the ignition wire (red)

and the battery wire (yellow). The power supply must

be connected to the wires via the fuse.

• Always connect the ignition wire (red) and the

battery wire (yellow) to the power source running

through the fuse box.

CAUTIONS

• Install this unit in the console of your car.

• Do not touch the metal parts of this unit during and

shortly after the use of the unit. Metal parts such as

the heat sink and enclosure become hot.

• When parking at a low ceiling area, turn off the unit

to store the antenna. As when the unit is installed in

the car with the function of auto antenna; the radio

antenna extends automatically when you turn on

the unit with the antenna control wire (ANT. CONT)

connected. (Pages 49 – 50)

Before installation

Precautions on installation and connection

• Mounting and wiring this product requires skills and

experience. For best safety, leave the mounting and

wiring work to professionals.

• Mount the unit so that the mounting angle is 30° or

less.

Searching for an item directly

While listening to the radio or during disc playback,

you can search for a station frequency/chapter/title/

folder/file/track directly using the number buttons.

1 Press # BS/DIRECT to enter the search

mode.

• Each time you press , the item to # BS/DIRECT

search for changes.

2 Press a number button to select a desired

item (station frequency/chapter/title/

folder/file/track).

• To erase a misentry, press .* +/CLEAR

3 Confirm the selection.

• For station frequency: Press / / / .H S T I

• For others: Press .ENTER

To exit the search mode: # BS/DIRECT Press .

47ENGLISH

• Make sure to ground the unit to a negative 12 V DC

power supply.

• Do not install the unit in a location exposed to direct

sunlight or excessive heat or humidity. Also avoid

places with too much dust or the possibility of water

splashing.

• Do not use your own screws. Use only the screws

provided. If you use the wrong screws, you could

damage the unit.

• After the unit is installed, check whether the brake

lamps, blinkers, wipers, etc. on the car are working

properly.

• Do not press hard on the panel surface when

installing the unit to the car. Otherwise scratches,

damage, or failure may result.

• If the power is not turned on (“Miswiring DC Offset

Error”, “Warning DC Offset Error” is displayed),

the speaker wire may have a short circuit or have

touched the chassis of the car and the protection

function may have been activated. In this case, the

speaker wire should be checked.

• Keep all cables away from heat dissipating metal

parts.

• If your car’s ignition does not have an ACC position,

connect the ignition wires to a power source that

can be turned on and off with the ignition key. If you

connect the ignition wire to a power source with a

constant voltage supply, such as with battery wires,

the battery may be drained.

• If the console has a lid, make sure to install the unit

so that the monitor panel will not hit the lid when

closing and opening.

Installation and Connection

Installation and ConnectionInstallation and Connection

• If the fuse blows, first make sure the wires are not

touching to cause a short circuit, then replace the old

fuse with one with the same rating.

• Insulate unconnected wires with vinyl tape or other

similar material. To prevent a short circuit, do not

remove the caps and do not let the cable out at the

ends of the unconnected wires or the terminals.

• Secure the wires with cable clamps and wrap vinyl

tape around the wires that comes into contact with

metal parts to protect the wires and to prevent short

circuit.

• Connect the speaker wires correctly to the terminals

to which they correspond. The unit may be damaged

or fail to work if you share the wires or ground ·

them to any metal part in the car.

• When only two speakers are being connected to the

system, connect both connectors either to the front

output terminals or to the rear output terminals (do

not mix front and rear). For example, if you connect

the connector of the left speaker to a front output ª

terminal, do not connect the connector to a rear ·

output terminal.

Parts list for installation

Note: This parts list does not include all the package

contents.

¥ Wiring harness (× 1)

ø Extension parking cable, 2 m (× 1)

π Round head screws, M5 × 8 mm (× 6)

[ Steering wheel remote input cable (× 1)

Only for DDX7018BT/DDX7018BTM/DMX7018BT/

DMX7018BTM

“ Flat head screws, M5 x 8 mm (× 6)

Only for DMX7018BT Australian/New Zealand

models

] Trim plate (× 1)

Only for DDX7018BTM/DMX7018BT Australian/New

Zealand models/DMX7018BTM/DDX718WBT/

DDX718WBTM/DMX718WBT/DMX718WBTM

‘ Microphone, 3 m (× 1)

Installation procedure

1 Remove the key from the ignition and

disconnect the · battery.

2 Make the proper input and output wire

connections for each unit.

3 Connect the speaker wires of the wiring

harness.

4 Connect the wires of the wiring harness

in the following order: ground, battery,

ignition.

5 Connect the wiring harness to the unit.

6 Install the unit in your car.

Make sure that the unit is installed securely in place.

If the unit is unstable, it may malfunction (e.g., the

sound may skip).

7 Reconnect the battery.·

8 Configure <Initial Settings>. (Page6)

48 ENGLISH

Installation and Connection

Installation and ConnectionInstallation and Connection

Installing the unit

Installing the unit using the mounting

bracket removed from the car

Car bracket

π “/

π “/ *

Note: Select the appropriate screws (supplied) for the

mounting bracket.

* Only for DDX7018BT/DDX7018BTM/DMX7018BT/

DMX7018BTM.

Installing the trim plate

(Only for DMX7018BT Australian/New Zealand

models)

]

Connecting external components

FRONT VIEW CAMERA

1 Navigation input (NAV)

2 TV tuner remote control output (REMO OUT)

3 Steering wheel remote controller input (REMO-IN)

• Connect to the car’s steering remote harness

using the steering wheel remote input cable ( ). [

Contact your KENWOOD dealer for details.

4 Audio video input (AV-IN)

5 Video output (V-OUT)

6 Rear view camera input (R-CAM)

7 Output terminals*1

• Left output (White)

• Right output (Red)

REAR: Rear speaker preouts

FRONT: Front speaker preouts

SW: Subwoofer preouts

For 3-way crossover:

REAR: Tweeter preouts

FRONT: Mid range speaker preouts

SW: Woofer preouts

8 Front view camera input (FRONT VIEW CAMERA)*2

*1 When connecting an external amplifier, connect its gro

to the chassis of the car; otherwise the unit may be dama

*2 Cable position differs according to the models.

49ENGLISH

REVERSE

PRK SW

REMOTE CONT

STEERING WHEEL

REMOTE INPUT

P.CONT

ANT.CONT

ILLUMI

MUTE

‘

Input 1

STEERING

REMOTE

ST REMOTE

GND

Input 2

[

Installation and Connection

Installation and ConnectionInstallation and Connection

Wiring connection

For DDX7018BT/DDX7018BTM

10 A fuse

Connect the antenna cord to the antenna terminal.

USB input terminal (1 m)

Purple with white stripe

White

]

/ White with black stripe

[

Green

]

/ Green with black stripe

[

Gray

]

/ Gray with black stripe

[

Purple

]

/ Purple with black stripe

[

Orange with white stripe

Brown

Light blue with yellow stripe

Blue with white stripe (12 V 350 mA)

Red (Ignition wire)

Yellow (Battery wire)

Black (Ground wire)

Light green

To the car’s reverse lamp harness when using the optional rear view camera

To the car light control switch

To rear speakers/tweeters*2 (right)

Not used.

To front speakers/mid range speakers*2 (right)

To rear speakers/tweeters*2 (left)

To front speakers/mid range speakers*2 (left)

Car battery

Car fuse

To the car chassis

To the OE remote adapter (not supplied) which is compatible with your car

Extension wire (

) To the car’s parking brake detection switch harness

(For best safety, be sure to connect the parking sensor.)

Ignition key switch

*1 Only for DDX7018BTM.

*2 For 3-way speaker system connection, see page 48.

To the power control terminal when using the optional power amplifier (Or)

To the control terminal of the motor antenna or to the power terminal for the booster amplifier of film-type antenn

Gray/Red

Bright green/Red

Purple/Red

Connect to your vehicle’s

steering remote harness.

Contact your KENWOOD

dealer for details.

50 ENGLISH

REMOTE CONT

STEERING WHEEL

REMOTE INPUT

P.CONT

ANT.CONT

ILLUMI

MUTE

REVERSE

PRK SW

Input 1STEERING

REMOTE

ST REMOTE

GND

Input 2

‘

[

Installation and Connection

Installation and ConnectionInstallation and Connection

For DMX7018BT/DMX7018BTM

10 A fuse

Connect the antenna cord to the antenna terminal.

USB input terminal (1 m)

Purple with white stripe

White

]

/ White with black stripe

[

Green

]

/ Green with black stripe

[

Gray

]

/ Gray with black stripe

[

Purple

]

/ Purple with black stripe

[

Orange with white stripe

Brown

Light blue with yellow stripe

Blue with white stripe (12 V 350 mA)

Red (Ignition wire)

Yellow (Battery wire)

Black (Ground wire)

Light green

To the car’s reverse lamp harness when using the optional rear view camera

To the car light control switch

To rear speakers/tweeters*2 (right)

Not used.

To front speakers/mid range speakers*2 (right)

To rear speakers/tweeters*2 (left)

To front speakers/mid range speakers*2 (left)

Car battery

Car fuse

To the car chassis

To the OE remote adapter (not supplied) which is compatible with your car

Extension wire (

) To the car’s parking brake detection switch har

(For best safety, be sure to connect the parking

sensor.)

Ignition key switch

To the power control terminal when using the optional power amplifier (Or)

To the control terminal of the motor antenna or to the power terminal for the booster amplifier of film-type antenn

Gray/Red

Bright green/Red

Purple/Red

Connect to your vehicle’s

steering remote harness.

Contact your KENWOOD

dealer for details.

*1 Only for DMX7018BT Australian/New Zealand

models/DMX7018BTM.

*2 For 3-way speaker system connection, see page 48.

51ENGLISH

REVERSE

PRK SW

P.CONT

‘

MUTE

D23

D22

D21

[

STEERING

REMOTE

Installation and Connection

Installation and ConnectionInstallation and Connection

USB input terminal (1 m)

For DDX718WBT/DDX718WBTM

Connector D: To the car’s steering remote harness

• Depending on the type of vehicle, it cannot be connected.

Connector B: To the car’s harness

Connector A: To the car’s harness

10 A fuse

Light green

Extension wire (

)

To the car’s parking brake detection switch harness

(For best safety, be sure to connect the parking sensor.)

Purple with white stripe To the car’s reverse lamp harness when using the optional rear view camera

Blue with white stripe

(12 V 200 mA)

Brown

To the control terminal of the motor antenna or to the power terminal for

the booster amplifier of film-type antenna

Pin Color and Function

A1 Orange/White Dimmer

A2 Yellow Battery

A3/A5 Blue Antenna control (12 V 300 mA)

A4 Red Ignition (ACC)

A6 Black Ground connection

A7/A8 White with black stripe

[

/ White

]

Left speaker (front/mid range*)

A9/A10 Gray with black stripe

[

/ Gray

]

Right speaker (front/mid range*)

B1/B2 Green with black stripe

[

/ Green

]

Left speaker (rear/tweeter*)

B5/B6 Purple with black stripe

[

/ Purple

]

Right speaker (rear/tweeter*)

D21 White Input 1

D22 Red Input 2

D23 Black Ground

* For 3-way speaker system connection, see page 48.

Not used.

Connect the antenna cord to the antenna terminal.

Produkt Specifikationer

Mærke:	Kenwood
Kategori:	Ikke kategoriseret
Model:	DDX7018BT

Har du brug for hjælp?

Hvis du har brug for hjælp til Kenwood DDX7018BT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Kenwood Manualer

Kenwood KSC-50CR Manual

25 Marts 2025

Kenwood KRK-15B Manual

24 Marts 2025

Kenwood VGS-1 Manual

24 Marts 2025

Kenwood KSC-25LS Manual

24 Marts 2025

Kenwood KPG-46U Manual

24 Marts 2025

Kenwood KPG-43U Manual

24 Marts 2025

Kenwood CAX-AD100 Manual

18 Marts 2025

Kenwood kMix FPX935 Manual

22 Februar 2025

Kenwood kMix FPX937 Manual

22 Februar 2025

Kenwood kMix FPX934 Manual

22 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterpik WP-490 Manual

10 April 2025

Daikin EAVX16S18DA9WG Manual

10 April 2025

Daikin RXYLQ40T7Y1B Manual

10 April 2025

Daikin RXYLQ42T7Y1B Manual

10 April 2025

Daikin ETVZ16S23EA6V7 Manual

10 April 2025

Daikin FXMA200AXVMB Manual

10 April 2025

Daikin FXZQ15A2VEB Manual

10 April 2025

Daikin ETVZ16S18EA9W Manual

9 April 2025

Daikin DSR1 Manual

9 April 2025

Simplified MFG SP18CAT120 Manual

9 April 2025