Klein Tools 450-100 Manual

Klein Tools Hæftemaskine 450-100

Læs nedenfor 📖 manual på dansk for Klein Tools 450-100 (6 sider) i kategorien Hæftemaskine. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/6
Cable Stapler Instructions
Instrucciones para engrapadora para cable (ver otro lado)
Instructions pour l’agrafeuse de câble (voir de l'autre côté)
11
1390250 Rev 04/20 C
450-100
FEATURE DETAILS / DETALLES DE LAS CARACTERÍSTICAS / CARACTÉRISTIQUES DÉTAILLÉES
ENGLISH
ENGLISH
7
Staple Discharge Area
8
Locking Buttons
9
Cable Guides
10
Actuation Force
11
Belt Clip Mounting Recess* (×2)
1
Cushioned handle
2
Tension Setting Lever
3
Staple Push Rod
4
Push Rod Release Latch
5
Belt Clip*
6
Staple / Cable Size Selector
*Belt clip can be mounted on either side of stapler. To switch sides, remove #2 Phillips screw, lift
clip and bracket, and move to mounting recess on opposite side. Place clip and bracket and screw
into place and secure by firmly tightening the screw into place. Use manual screwdriver only; do
not overtighten.
7
Área de descarga de grapas
8
Botones de bloqueo
9
Guías de cable
10
Fuerza de accionamiento
11
Ranura para fijar el clip para cinturón* (2)
1
Mango acojinado
2
Palanca de ajuste de tensión
3
Empujador de grapas
4
Bloqueo de liberación del empujador
5
Clip para cinturón*
6
Selector de tamaño de grapa/cable
*El clip para cinturón puede fijarse en cualquier lado de la engrapadora. Para cambiar de lado, retire
el tornillo Phillipsn.º2, levante el clip y el soporte y fíjelo en la ranura del lado opuesto. Ubique el
clip, soporte y tornillo en suslugares y asegure ajustando firmemente el tornillo. Utilice solamente
un desarmador, no apriete demasiado.
7
Zone de décharge des agrafes
8
Boutons de verrouillage
9
Guide-câble
10
Force d’actionnement
11
Encoche de montage de la pince pour ceinture* (×2)
1
Manche coussiné
2
Levier de réglage de la tension
3
Poussoir des agrafes
4
Loquet de dégagement du poussoir
5
Pince pour ceinture*
6
Sélecteur de la taille des agrafes et des câbles
*La pince pour ceinture peut être installée de chaque côté de l’agrafeuse. Pour la changer de côté,
retirez la vis à tête cruciforme no2, soulevez la pince et son ancrage et déplacez-les dans l’encoche de
montage du côté opposé. Tenezlapince et son ancrage en place, puis fixez-les en serrant fermement
la vis. Utilisez uniquement un tournevis manuel; ne serrez pas trop fort.
ESPAÑOL
FRANÇAIS
FIG. 1 FIG. 2
FIG. 3
1
5
8
7
10
4
3
6
2
CUSTOMER SERVICE
KLEIN TOOLS, INC.
450 Bond Street Lincolnshire, IL 60069 1-877-775-5346
customerservice@kleintools.com www.kleintools.com
WARRANTY
www.kleintools.com/warranty
OPERATING INSTRUCTIONS
NOTE: Use only on wood frames / structures of low or medium density. Hard woods may cause
malfunction or partial staple penetration. Always ensure proper staple size is loaded in cable stapler.
STAPLE SELECTION (FIG. 1, FIG. 2):
WORKS EXCLUSIVELY WITH KLEIN TOOLS STAPLES. NOT COMPATIBLE WITH OTHER BRANDS OF STAPLES.
Determine appropriate staple size for cable type (see staple size guide on side of stapler):
• 450-001 - 1/4" for: CAT3, CAT5e, or speaker wire
• 450-002 - 5/16" for: CAT3, CAT5e, or CAT6/6A, Coax
• 450-003 - 19/32" for: NM: 14/3, 14/3G, 12/3, Qty 1 or 2 Coax, or Qty 1 to 3 CAT3/5e/6/6A
• 450-004 -
31/64" for: NM: 14/2, 14/2G, 10/2, 10/2G, or Qty 1 or 2 speaker wires
For use with 450-001 or 450-002: Ensure the
Staple / Cable Size Selector
6
is in the down position
(FIG. 1). If it is in the up position, grasp staple guide firmly and pull down until locked. The
Staple /
Cable Size Selector
6
is locked in the down position when the Locking Buttons
8
are fully released.
For use with 450-003 or 450-004: Ensure the Staple / Cable Size Selector
6
is in the up position (FIG.
2). If it is in the down position, depress both Locking Buttons
8
(on both sides of stapler), and slide the
Staple / Cable Size Selector
6
to the up position. Ensure that the cable opening is fully exposed.
STAPLE TENSION ADJUSTMENT:
For use with 450-001 and 450-002: Tension Setting Lever
2
should be in the lower tension, down position.
For use with 450-003 and 450-004: Tension Setting lever
2
should be in the higher tension, up position.
To change between positions, push in and turn gently. For reference, the higher tension setting may
be necessary when using the 450-001 and 450-002 with harder woods, and the lower tension may be
necessary when using 450-003 and 450-004 on softer materials, such as drywall. Perform a test setting
determination on a non-visible surface.
LOADING STAPLES:
1. Hold staple gun upside down, depress
Push Rod Release Latch
4
, pull out
Staple Push Rod
3
.
2. Insert appropriate staple, with the legs pointing up (FIG. 3).
3. Firmly push the
Push Rod Release Latch
4
closed.
NOTE: DO NOT mix staples of different sizes. Partial strips, damaged strips or mixing of different sized
staples may jam the stapler.
STAPLING CABLE:
1. Locate stapler over cable, ensuring cable is contained within the
Cable Guides
9
for entire length of
stapler, front to back.
2. Press Handle
1
firmly downward to release staple.
3. If staples jam, ensure that you are using the proper staple size and tension setting. Also ensure that
you are not attempting to staple into a surface that cannot be penetrated by a staple. In the event of a
jam, clear jammed staple gently, wearing gloves to prevent injury to hands.
WARNINGS
Read all instructions thoroughly prior to use. Failure to read, understand, and follow all instructions
may result in serious injury.
• Never work on or near live electric circuits.
• Always wear approved eye protection and hearing protection.
• Keep fingers clear of staple discharge area when operating or clearing a jam.
• Only direct staple discharge towards surface intended to be stapled; never point towards any body part.
• Ensure correct staple size is selected before discharging.
• Use proper positioning of the cable guide to prevent staples from piercing the cable
• Always be cautious of potential hazards such as electrical wiring, damp or wet conditions, unstable surfaces.
• For professional use only.
• Keep away from children.
The Klein Tools Cable Stapler features a forward action for greater stability. It is designed to allow user to
push the handle, rather than squeeze, delivering easy, consistent performance. The staples are released
from the front end of stapler, nearest to where the handle is pressed down. A cable guide along the entire
bottom surface protects the cable from being crushed during the stapling process.
WARNING SYMBOLS ON PRODUCT
Warning or caution
Always wear approved eye protection
Do not use on live electric circuits
Always wear approved hearing protection
Read instructions before using

Produkt Specifikationer

Mærke: Klein Tools
Kategori: Hæftemaskine
Model: 450-100

Har du brug for hjælp?

Hvis du har brug for hjælp til Klein Tools 450-100 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Hæftemaskine Klein Tools Manualer

Klein Tools

Klein Tools 450-100 Manual

18 August 2024

Hæftemaskine Manualer

Nyeste Hæftemaskine Manualer

Total

Total TCBNLI2001 Manual

16 December 2024
Sun Joe

Sun Joe BDL-A0202 Manual

7 December 2024
Sun Joe

Sun Joe BDL-A0200 Manual

7 December 2024
Whirlpool

Whirlpool YWEE515S0LB Manual

4 December 2024
Whirlpool

Whirlpool YWEE515S0LV Manual

4 December 2024
Biltema

Biltema 87-1004 Manual

12 November 2024
Biltema

Biltema 87-1005 Manual

12 November 2024
Biltema

Biltema 87-1006 Manual

11 November 2024
MSW

MSW -STAPLER 1500 Manual

15 Oktober 2024
Whirlpool

Whirlpool YWFES5030RB Manual

11 Oktober 2024