La Crosse Technology 308-1910R Manual


Læs nedenfor 📖 manual på dansk for La Crosse Technology 308-1910R (2 sider) i kategorien Termometer. Denne guide var nyttig for 22 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Wireless Thermometer
Model: - | Instruction Manual 308 1910
View temperature with a glance. Precise real-time indoor and
outdoor temperature with MIN/MAX readings in Fahrenheit or
Celsius, manual set time and alarm with snooze.
SETUP INSTRUCTIONS STEP BY STEP
STEP 1:
Ensure that the transmitter is within 10 feet of the
Wireless Thermometer.
Remove battery cover from TX19 transmitter.
Insert 2 new AAA batteries (not included) into the
transmitter. Observe the correct polarity.
STEP 2:
Remove battery cover from the Wireless
Thermometer (follow the arrow on the bottom of the battery
cover).
Insert 2 new A batteries (not included) into AA
the back of the Wireless Thermometer.
Observe the correct polarity (see marking
inside the battery compartment).
Within 3 minutes, the Wireless Thermometer
will show readings in the outdoor temperature
area on the wireless thermometer.
Note: Allow the Wireless Thermometer and
the transmitter to stay within 10 feet of each
other for the rst 15 minutes of set up.
Do Not Mix Old and New Batteries
Do Not Mix Alkaline, Standard, Lithium or Rechargeable
Batteries
TROUBLE SHOOTING
If the Wireless Thermometer does not display the outdoor
temperature after 3 minutes, remove the batteries from both units
and repeat the setup process.
From normal display, hold the UP ARROW button for 3 seconds
to search for the outdoor temperature transmitter.
For optimal 433MHz signal reception, the outdoor transmitter
should be placed within 100 feet (30 meters) from the indoor
Wireless Thermometer.
The outdoor temperature reception icon willash:
During initial setup, for up to three minutes, until it
connects with the transmitter.
About every minute afterwards as the wireless
thermometer receives an update.
When the UP ARROW button is held for 3 seconds to begin a
search for the transmitter.
SET TIME
From Time m , hold the TIME button for 3 seconds to enter time ode
set mode.
The Hour will ash. Press and release the ARROW HOUR:
buttons to select the correct hour. Press and release the TIME
button once to move to the minutes.
MINUTES: The Minutes will ash. Press and release the
ARROW buttons to select the correct hour. Press and release
the TIME button once more to exit the program menu.
FAHRENHEIT/CELSIUS
Default temperature reading in Celsius is .
From Time m , press and release the F/°C button to select ode
Fahrenheit temperature readout.
12 HOUR/24 HOUR TIME
Default time format is hour time format. 24
From Time m , press and release the 12/24h button to select ode
12 hour time readout.
LOW BATTERY ICON
The low battery icon will show above the outdoor
temperature when it is time to change batteries.
MAXIMUM/MINIMUM TEMPERATURE READINGS
VIEW: Press and release the MIN/MAX button
once to show the maximum temperature
records. Press and release the MIN/MAX button
again to view the minimum temperatures. Press
and release the MIN/MAX button a third time to
return to current temperature.
RESET: Hold the MAX/MIN key for 2 seconds
to manually clear all the MIN/MAX records.
ALARM SET
From Time m , press and release the ALARM button to switch to ode
Alarm Mode. The letters “AL” will appear between the hours and the
minutes. In Alarm Mode hold the ALARM button for 3 seconds to
enter alarm set mode.
The Hour will ash. Press and release the ARROW HOUR:
buttons to select the correct hour. Press and release the ALARM
button once to move to the minutes.
MINUTES: The Minutes will ash. Press and release the
ARROW buttons to select the correct hour. Press and release
the ALARM button once more to exit the program menu.
Note: When the alarm sounds, it continues for 2 minutes and then
shuts o completely.
SNOOZE
When the alarm sounds, press the SNOOZE button to silence the
alarm for 5 minutes. The alarm icon will ash.
The snooze function can be repeated.
Press any other button to turn the alarm o for 24 hours.
ACTIVATE/DEACTIVATE ALARM
From Time m , press and release the ALARM button to switch to ode
Alarm mode. The letters “AL” will appear between the hours and the
minutes.
ACTIVATE: In Alarm mode, press and release the UP ARROW
button to activate the alarm. The alarm icon will appear.
DEACTIVATE: In Alarm m , with the bell icon visible, press and ode
release the UP ARROW button to deactivate the alarm. The bell icon
disappears.
POSITIONING THE TEMPERATURE TRANSMITTER
The remote temperature transmitter should be mounted vertically to
avoid damage. Place both units in the desired shaded locations, and
wait approximately 1 hour before permanently mounting the


Produkt Specifikationer

Mærke: La Crosse Technology
Kategori: Termometer
Model: 308-1910R

Har du brug for hjælp?

Hvis du har brug for hjælp til La Crosse Technology 308-1910R stil et spørgsmål nedenfor, og andre brugere vil svare dig




Termometer La Crosse Technology Manualer

Termometer Manualer

Nyeste Termometer Manualer