Lanberg ICS-0808-0020 Manual

Lanberg Overvågningskamera ICS-0808-0020

Læs nedenfor 📖 manual på dansk for Lanberg ICS-0808-0020 (3 sider) i kategorien Overvågningskamera. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/3
QUICK INSTALLATION GUIDE
WIRELESS KIT
Statement
Installation Instruction Of WIFI NVR KIT Record video Video Backup
Video Playback
Setup The System
Safety Caution
Out Of Box Audit
NVR
HDD Install
IPC
Thank you for purchasing our product! This quick user guide will talk about main usages of
the product. More information can be found on our website and the help www.lanberg.eu
center. This user guide may contain inaccurate content due to hardware and software
upgrade. It is subject to change without previous notice.
Note:
Wireless NVR can’t be connected to WIFI router wirelessly at present. They can be only
connected by network cable.
This system is standalone with embedded Linux Operating System in the NVR. Just like a
desktop PC, need to hook a screen to the NVR to enter the OS. Any TV , monitor with VGA
or HDMI input should work for it.
1 Install antennas for cameras and the NVR;.
2.Connect a screen to the NVR via its HDMI or VGA port(HDMI and VGA cable
not included);
3. Plug the NVR to power(use bigger 12V 2A power adapter);
4. Plug cameras to power(use smaller 12V 1A power adapters);
5. Within seconds, you should see camera’s images on the screen;
6.Plug the mouse(included) to an USB port on back of NVR. You shall then be able to operate
on the system.
In the OS you can find fullest functionalities including live view, record, playback, video
backup and all settings.
Default ID: admin
Password: none (means leaving the password empty, just click login)
Tips：To protect your privacy, please set your password at earliest convenience. Right click
the mouse Go to System Setup System Admin User Management to set password.→ → →
Record video is very easy on camera system.
1.Time Recording: Setup period of time of recording on NVR GUI .Right click mouse→
System Setup Record setup Record Plan.Click “time”and put mouse icon on the upper → →
left corner(for example“1”as picture shows),press and drag the mouse to the right to choose
the time.The list will turn to red.
2.Motion Recording: Only detect motion and then start recording.Right click mouse→
System Setup Record setup Record Plan.Click“motion”and put mouse icon on the upper → →
left corner(for example“1”as picture shows),press and drag the mouse to the right to choose
the time. The list will turn to green.
3. → Alarm recording: Right click mouse System Setup→Record setup→Record Plan.Click
“Alarm”and put mouse icon on the upper left corner(for example “1”as picture shows),press
and drag the mouse to the right to choose the time. The list will turn to yellow.
Note: Users can setup any period of time they want,for example 0:00:00 - 23:59:59,That’s
24 hours *7 days recording.When NVR detects hard disk,the default setting will be 24
hours*7 days recording.
Use U disk to copy video,so easy and convenient!
1.2 USB ports: Plug U flash disk into
the USB port of NVR. Right click
on main menu Video backup→ →
choose backup channel→choose
video mode setup searching →
time search→ →choose recording
file on the list→video backup
(support 32G U flash disk at max.
Recording file is packed one hour
per time.)
Steps:right clik mouse in main menu Video playback choose date,channel,record mode→ →
→ →click search then can view playback file.
1. IIIustration for playback button: play, pause: fast forward*2,*4,*8；
2. Play file: Choose the recording file in file list,as number“1”shown in picture. Choose one
of the recording, click “play”to play to recording file;
3. Video backup: Choose the recording file in file list,as number“1”shown in picture.insert
the U flash disk, click “video backup”to backup the file;
4. Timeline: Click “date”and “time”at left bottom to check the timeline of recording, as
number“2”shown in picture;
5. On the timeline with recording file,left click the mouse, the can playback the file.
Tips: the system may not include hard disk depending on the kit you selected. the NVR works
most 3.5" SATA HDD or 2.5"SATA HDD
1.Unplug your NVR from power,unscrew and remove the top cover.
2.Connect the SATA power and data cables from the NVR to the
corresponding ports on your HDD (as shown).
lding the hard drive and the DVR ,gently turn it over and line up
e holes on the hard drive with the holes on the NVR. using a
illips screwdriver,screw the provided screws into the holes and
semble the cover.
ote: New HDD have to be formatted before recording.
o get better WIFI signal, it had better place the NVR in open
ea and high position.
1. Please do not put any fluid container on the product.
2. Please use the product in ventilated environment and prevent blocking the vents.
3. Please use included power supply with the product to prevent damage to the product.
4. Please use the product under its standard working temperature and humidity.(advised
in this manual or distributor’s website)
5. Dust on PCB may cause short circuit.It is suggested to clean the dust on PCB timely
to make the product work properly.
6. Please obey the regulation and policy in your country and area during the installation
of this.
After receiving the product, please check all products and accessories with information
below. If any is missed or damaged, please contact the distributor.
1 Double antennas to WIFI range.WIFI Antenna Ports:
2. WAN Port: Connect your NVR to Internet
3 VGA Port:. For viewing on VGA monitor
4 HDMI Port: . For viewing on HDTV
5 USB Ports: . For mouse and backup
6 Power Input.
1. WiFi connection with NVRWIFI antenna: ；
2 input power 12V 1A;. DC Port:
3. Reset button: press reset button for 10 seconds to restore factory setting
and enter into matching-code mode.
ITEM:
WIFI NVR
Screw bag(4 screws for HDD)
DC 12V 2A power supply (for NVR)
User manual
WIFI IP Camera*
DC 12V 1A power supply(for IPC)*
Screw bag (for IPC）*
Antenna Extension Cord*
QUANTITY:
1pcs
1pcs
1pcs
1pcs
4/8pcs
4/8pcs
4/8pcs
1/2(4CH/8CH)pcs
View On PC Via IE (Internet Explorer)
1. When your PC is in same LAN with the NVR （normally means they are connected to the
same router）
Step1.Find the IP address and port# of your NVR(IP address can be found in System
Setup Network Setup).→
2.OPTIONAL -When your computer/laptop is out of home/local network (eg. You want to
have a preview from the office). Access from the CLOUD ID to the device
Step 1. Open your browser and enter the website address in the search engine:
www.noip.com - the website owner provides free DDNS services.
Step 2. Required account creation.
Enter: Hostname - the name you chose (eg Michał123) Choose a domain from the
drop-down list (eg DDNS.net Click on "Sign UP" to create an account.) After completing
the data, please confirm your email to activate your account. step by step just like a service
provider leads you.
Step 3. NVR settings - Please enter
System Options→Network →DDNS
Director choose "NO-IP"→URL
enter the hostname (eg Michał123)
and the selected member from the
drop-down list (eg ddns.net)→User
enter the email given during
registration→Password enter the
password provided during
registration. Click the TEST button.
If the data is entered correctly, the
tests will pass
Step 4. In the browser, enter, for
example, michal123.ddns.net and
then we will open a page identical to
the one in the local network. You
must log in with administrator data
from the NVR (login and password).
Step 2. Enter the NVR’s IP address
in your IE browser for example:
http://192.1.1.7(If the default WEB
port 80 has been changed e.g. to
100,you’ll need to add new port
number when input IP address in
the browser, for example:
http://192.168.1.7:100).
NOTE: For proper configuration, you
should have public IP and port
forwarding (available manual also at
www.noip.com right after
registration). View On Mobile
* quantities given in order for a 4-channel, followed by an 8-channel set (4ch/8ch).

Produkt Specifikationer

Mærke: Lanberg
Kategori: Overvågningskamera
Model: ICS-0808-0020

Har du brug for hjælp?

Hvis du har brug for hjælp til Lanberg ICS-0808-0020 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Overvågningskamera Lanberg Manualer

Lanberg

Lanberg ICS-0808-0020 Manual

5 August 2024
Lanberg

Lanberg ICS-0404-0020 Manual

4 August 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

D-Link

D-Link DCS-2100+ Manual

20 Oktober 2024
Trebs

Trebs CCD-401C Manual

15 Oktober 2024
D-Link

D-Link DCS-7510 Manual

14 Oktober 2024
D-Link

D-Link DCS-6113 Manual

14 Oktober 2024
Foscam

Foscam FI9900EP Manual

14 Oktober 2024
Alecto

Alecto DVC-215IP Manual

13 Oktober 2024
Hikvision

Hikvision DS-2DE7A245IX-AE/S1 Manual

13 Oktober 2024
Hikvision

Hikvision DS-2TD6267-100C4L Manual

12 Oktober 2024
Hikvision

Hikvision DS-2CD2325FWD-I Manual

12 Oktober 2024
TRENDnet

TRENDnet TV-IP302PI Manual

11 Oktober 2024