Lezyne Power Drive XL (2014) Manual

Lezyne Cykellygte Power Drive XL (2014)

Læs nedenfor 📖 manual på dansk for Lezyne Power Drive XL (2014) (2 sider) i kategorien Cykellygte. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

English User Manual

READ ENTIRE MANUAL BEFORE OPERATION to ensure proper use and care of your new

Lezyne LED light. Trac laws mandang lighng vary from country to country. Inform

yourself about lighng laws in the country of use.

Warnings

DO NOT LOOK DIRECTLY INTO LIGHT BEAM or shine into eyes of another.

DO NOT SUBMERGE UNDER WATER. Lezyne LED lights are water resistant under normal

condions, but are not waterproof. If moisture gets inside light body, remove tailcap

and air-out unl completely dry.

DO NOT ATTEMPT TO REMOVE ELECTRONICS. Doing so will void warranty.

Use only genuine Lezyne branded LIR 18650 baeries. Never aempt to use two (2) LIR

123A baeries in place of one (1) LIR 18650 baery. See Charging for instrucons on

installing baery.

Lezyne USA, Inc. and Lezyne Co., Ltd. do not accept any liability for injuries or other dam-

ages resulng from the use of this product in any circumstances.

Warranty

In U.S. and U.K., Lezyne LED Lights carry a two (2) year warranty from the original

purchase date to the original owner (proof of purchase is required). Lezyne Baeries

carry a six (6) month warranty from the original purchase date. Lezyne warranes cover any

manufacturing defects in materials or workmanship. Issues not covered by warranty include

normal wear & tear, improper installaon, aempng to access or modify electronics, dam-

age or failure due to accident, misuse, abuse and/or neglect.

For warranty issues outside of the United States, contact the distributor/retailer for your

country or region directly. To nd a distributor near you, visit:

hp://lezyne.com/contact/distributors

Mounting

1. Slide clamp over handlebar with bolt hole facing forward, place top mount on

clamp, insert thumbscrew from boom.

2. Tighten thumbscrew unl snug; clamp should not rotate on handlebar. DO NOT

 OVERTIGHTEN.MaxTorque:5.0Nm

3. Slide LED light into top plate from front. CONFIRM TAB ENGAGEMENT.

To remove LED light, depress release tab; pull light forward.

NOTE: When installing on carbon surfaces, verify ghtening torque recommendaon

with the carbon parts manufacturer to prevent over ghtening that can cause damage to

the carbon material and/or under ghtening that can cause lack of xing strength.

Operation

1. ON/OFF: hold buon two (2) sec.

2. Mode cycle: click buon

3. Overdrive Race Mode: hold buon ve (5) sec.

OVERDRIVE RACE MODE: With the light OFF, hold buon for ve (5) seconds, unl light

ashes. The light is now in Overdrive Race Mode where only Overdrive and Economy out-

puts are selectable. The light will remain in Overdrive Race Mode even when switched

OFF. Repeat the step above to return to the normal mode set.

THERMAL PROTECTION: If the operang temperature of the light is too high, the light

automacally lowers the lumen output.

MAINTENANCE: For water resistance, ensure that tailcap, buon, and USB protecve

cover are fully installed before every use. Keep tailcap threads clean and apply small

amount of thick, mulpurpose grease to tailcap threads if necessary.

Run Times and Modes

SUPER DRIVE:

FL1 STANDARD

OVERDRIVE ENDURO BLAST ECONOMY FLASH 1

575

LUMENS

350

LUMENS

500

LUMENS

175

LUMENS

150

LUMENS