Lorex LNWDB1 Manual

Lorex Dørklokke LNWDB1

Læs nedenfor 📖 manual på dansk for Lorex LNWDB1 (1 sider) i kategorien Dørklokke. Denne guide var nyttig for 24 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
LNWDB1_QSG_EN_R2
HD Video Doorbell
To prepare for installation:
Before beginning setup, there are some essential preparations to
make.
TURN OFF THE POWER RUNNING TO YOUR EXISTING
DOORBELL AND CHIME BOX AT THE BREAKER. Test that
power has been disconnected for both the doorbell and chime
box power by pressing the doorbell. There should be no chime
sound.
Remove your existing doorbell and disconnect wiring.
Microphone
Call button
Speaker
IR LEDs
Camera
PIR sensor
Power ports
Front Panel
Indicator LED strip
Behavior During Setup After Setup
Pulsing Hotspot active Calling
Resetting
Solid Power on Talking
Flashing Ready for setup Network issues
Quick Start Guide
LNWDB1 Series
lorex.com
HD Video Doorbell
Package Contents
Product Overview PreparationSTEP 1:
Back Panel
Need Help?
Visit us online for up-to-date software
and complete instruction manuals
Click on the tabDownloads
4
Visit lorex.com
Search for the model
number of your product
Click on your product
in the search results
3
2
1
Copyright © 2020 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right to
modify product design, specications and prices, without notice and without incurring
any obligation. E&OE. All rights reserved.
Screwdriver
Mounting Screws &
Anchors (×4)
Read this guide carefully and keep it for future reference.
Follow all instructions for safe use and handling of the product.
Use the product within given temperature, humidity and voltage levels noted in the
product’s specications.
Do not disassemble the doorbell.
Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh,
chemical-based cleaners.
Safety Precautions
Not intended for submersion
in water. Installation
in a sheltered location
recommended.
This doorbell includes an Auto
Mechanical IR Cut Filter. When
the camera changes between
Day/Night viewing modes, an
audible clicking noise may
be heard from the doorbell.
This clicking is normal, and
indicates that the camera lter
is working.
Audio recording without
consent is illegal in certain
jurisdictions. Lorex Corporation
assumes no liability for use
of its products that does not
conform with local laws.
Disclaimers
Chime Kit
Reset button
microSD slot
Wire Caps (×3)
Doorbell & Chime Cables
Door Frame Screws (×3)
TIP: Bend the power cables so they do not fall through the hole in
the wall.
Next, use the mounting bracket to mark holes for mounting. Use the mounting accessories specied below depending on mounting location.
STEP 2: Secure the mounting bracket
For installing on brick, stucco, or siding:
For installing on a metal door frame:
1”
25mm
4.7”
120mm
1.7”
45mm
Dimensions
Use a 15/64” drillbit to drill
holes where marked. Use
the included mounting
screws plastic anchors and
to secure the mounting
bracket to the wall.
Use a 3/32” drillbit to drill
holes where marked. Use
the included door frame
screws to secure the
mounting bracket to the
door frame.
NOTE
For both installations, ensure the power cables from the wall t
comfortably through .the hole in the mounting bracket
Remove the metal mounting plate from the back of the doorbell.
Power Port Screws (×2)
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
FCC Notice


Produkt Specifikationer

Mærke: Lorex
Kategori: Dørklokke
Model: LNWDB1

Har du brug for hjælp?

Hvis du har brug for hjælp til Lorex LNWDB1 stil et spørgsmål nedenfor, og andre brugere vil svare dig