Lorus VD67 Manual

Lorus Ur VD67

Læs nedenfor 📖 manual på dansk for Lorus VD67 (2 sider) i kategorien Ur. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
NREVD67 10-2005
CAL. VD67 (RL8 SERIES)
C H A R A C T E R I S T I C S
1. T ime: Indicated by the hour, minute and
small second hands.
2. Date: Displayed in numerals.
3. Stopwatch: Measures up to 12 hours in 1/5
second increments.
Split time measurement
Mi nut e ha nd
D I S P L AY A N D C R O W N O P ER AT I O N
a. Normal position : Free
b. First click : Date setting
c. Second click : Time setting
Adjusting the stopwatch
hand position
Ho ur
ha n d
Sm all se co n d
ha n d
A
B
a b c
Cr o wn
D at e
S t op wa t ch
mi nut e h a nd
S t op wa t ch
ho ur ha nd
S t op wa t ch
1/ 5- se co n d h a nd
SET T I NG T HE TI ME AND AD J US T I NG
T H E S T O P WAT C H H A N D P O S I T I O N
Mi nut e ha nd
Ho ur ha nd
1) Time/Calendar setting
Sm all se co n d
ha n d
1. Pull out the crown to the first click, and turn it
clockwise until the prev ious days date
appears.
2. Pull out the crown to the second click when
the small second hand is at the 12 oclock
position.
3. Turn the crown clockwise until the desired
date appears.
4. Turn the crown to set the hour and minute
hands.
5. Push the crown back in to the normal position
in accordance with a time signal.
Notes:
1. Do not set the date between 9:00 p.m. and
1:00 a.m., as the date may not change
properly.
2. When setting the hour hand, be sure to check
that AM/PM is correctly set. The watch is so
designed that the date changes once in 24
hours.
* Turn the hands past the 12 oclock marker to
determine whether the watch is set for the
A.M. or P.M. period. If the date changes,
the time is set for the A.M. period. If not, the
time is set for the P.M. period.
3. When setting the minute hand, first advance
it 4 to 5 minutes ahead of the desired time
and then turn it back to the exact minute.
B
1. Pull out the crown to the second click.
2. Press button A. The stopwatch 1/5-second
hand turns a full circle.
3. Press but t on A re pea te dly to rese t the
st opwat ch 1/5-second hand t o the0
position.
4. Press button B. The stopwatch minute hand
turns a full circle.
5. Pre ss but t on B re pea tedly to re se t the
stopwatch hour and minute hand to the 0
position.
* T h e s t o p w a t c h h o u r h a n d m o v e s
correspondingly with the stopwatch minute
hand.
* The stopwatch hands turn continuously if the
respective buttons are kept pressed, and the
hands stop when the respective buttons are
released.
6. Push t he cr own back in t o the no rm al
position.
St opwat ch
ho ur ha nd
S t op wa t ch
mi nut e h a nd
2) Stopwatch hand position adjustment
If the stopwatch hands are not in the 0
position, follow the procedure below to set
them to the 0 position.
S t op wa t ch
1/ 5- se co n d h a nd
A
The stopwatch can measure up to 12 hours
in 1/5 second increments.
The measured time is indicated by the three
stopwatch hands that move independently
of the hands for time display.
When the measurement reaches 12 hours,
the stopwatch automatically stops counting.
S T O P WAT C H
A: St ar t / St o p
B:S pl it / S p li t
re le a se / Re se t
S t op wa t ch
1/ 5- s ec ond hand
S t op wa t ch
ho ur ha nd
S t op wa t ch
mi nut e h a nd
Before using the stopwatch, be sure to check
that the crown is set at the normal position
and that the stopwatch hands are reset to
the 0 position.
* If t he hands do not ret urn to t he 0
po sit i on, f ol lo w t he pr oce du re in
n
SET TING THE T IME AND ADJUST ING T HE
STOPWATCH HAND POSITION.
Crown


Produkt Specifikationer

Mærke: Lorus
Kategori: Ur
Model: VD67

Har du brug for hjælp?

Hvis du har brug for hjælp til Lorus VD67 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ur Lorus Manualer

Lorus

Lorus VX7P Manual

22 August 2024
Lorus

Lorus VX9P Manual

20 August 2024
Lorus

Lorus Z021 Manual

19 August 2024
Lorus

Lorus Z004 Manual

19 August 2024
Lorus

Lorus Z015 Manual

18 August 2024

Ur Manualer

Nyeste Ur Manualer