Meade S102 Manual


Læs nedenfor 📖 manual på dansk for Meade S102 (2 sider) i kategorien Teleskop. Denne guide var nyttig for 13 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
MEADE S102 USERS GUIDE
WARNING!
Never use a Meade telescope to look at the
Sun! Looking at or near the Sun will cause in-
stant and irreversible damage to your eye. Eye
damage is often painless, so there is no warning to
the observer that damage has occurred until it is too
late. Do not point the telescope at or near the Sun.
Do not look through the telescope or viewfinder as it
is moving. Children should always have adult supervi-
sion while observing.
INTRODUCTION
Your telescope is an excellent beginner’s instrument and is
designed to observe objects in the night sky and also on
land. It can be your personal window on the universe or al-
low you to intimately study the behavior of nesting birds on a
distant hillside. The telescope is shipped with the following
parts:
ASSEMBLY
The tripod is the basic support for your telescope and comes
pre-assembled from the factory; except for the accessory
tray. In order to use the scope a small amount of assembly is
required. Follow the below steps to assemble the telescope.
Note: Number in brackets, e.g., (3), refer to the item numbers
in Fig. A.
1. To setup the tripod, spread the legs out evenly and place
on solid ground. Loosen the leg lock knobs and extend
the inner legs to desired height. Do this for each leg until
the top of the tripod is approximately level. Re-lock the
leg lock knob.
2. Attach the accessory tray to the tripod by threading it
into the center nut between the tripod legs.
ATTACHING THE OPTICAL TUBE ASSEMBLY (OTA)
1. Remove the two lock knobs (2) from the optical tube
mount.
2. -Slide the Slow-motion control rod (8) into the slow-mo
tion control lock knob hole (9).
3. Place the optical tube (1) between the forks of the
mount, oriented as shown.
4. Thread the lock knobs (2) through each of the holes in
the forks of the mount and tighten to a firm feel.
ATTACHING THE RED-DOT FINDER
An eyepiece (1) has a narrow field of view. The included
viewfinder (4) has a wider field of view and red dot to make
it even easier to locate the viewing object. The red dot view-
finder also comes with an easy to install dovetail bracket.
1. To install the red dot viewfinder, slide the viewfinder
bracket into the dovetail adapter ( ).Fig C
2. -Next, secure the viewfinder in place with the single lock
ing knob.
REMOVING THE DUST COVERS
1. -Remove dust covers(6) at the front of the scope by pull
ing the cover away from the telescope.
2. Remove the dustcover from the focuser by pulling it out
of the focuser draw tube.
INSERTING THE EYEPIECE
1. Slide the 26mm eyepiece (5) into focuser draw tube.
2. Tighten thumbscrew to hold the eyepiece in place.
ALIGNING THE RED-DOT FINDER
Perform the first part of this procedure during the daytime
and the last step at night.
1. Point the telescope at an easy- to-find land object such
Figure C
Adjustment
knobs
Lock
Knob
On/Off
Lock
knob
Slide
rod
through
hole
Place
tube
between
forks
Lock
knob
Lock
knob
Figure B Figure D
102mm Optical tube
Red Dot nder
Yoke-style mount
Software disk
Aluminum tripod with
accessory tray
Two 1.25” Eyepieces:
MA26mm, MA9mm
Diagonal Mirror
1.25” 2X Barlow Lens
Smart Phone Adapter
Instruction sheet
Figure A
(not shown)
(not shown)
1. -Optical Tube As
sembly (OTA)
2. Vertical Motion Lock
Knob
3. Focusing Knob
4. Red-dot Viewnder
5. Eyepiece
6. Front Dust Cap
7. Diagonal Mirror
8. Slow-Motion Control
Rod
9. Slow-Motion Control
Lock Knob
10. Horizontal motion
lock knob
11. Tripod leg locks
12. Accessory tray
13. Tripod legs
14. Dew Shield


Produkt Specifikationer

Mærke: Meade
Kategori: Teleskop
Model: S102

Har du brug for hjælp?

Hvis du har brug for hjælp til Meade S102 stil et spørgsmål nedenfor, og andre brugere vil svare dig