Mobotix MX-Bell1-Button-F1 Manual

Mobotix Ikke kategoriseret MX-Bell1-Button-F1

Læs nedenfor 📖 manual på dansk for Mobotix MX-Bell1-Button-F1 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 13 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

The HiRes Video Company

www.mobotix.com

HiRes Video Innovations– Made in Germany

The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized concept has made high-resolution video

systems cost-ecient.

MOBOTIX AG • D-67722 Langmeil • Tel: +49 6302 9816-103 • Fax: +49 6302 9816-190 • sales@mobotix.com

BellRFID Quick Install

Bell Button Module with RFID

Technology for up to Five Parties

Module for MOBOTIX IP Video Door Station, keyless entry and

mailbox control, can be combined with the dierent bell button sets

MX-Bell1-Button-F1/F2/F3/F4/05/XL1

Free-of-charge printing service on

www.mobotix.com> Support

• BellRFID base module with 1 admin and 5 user RFID cards

• Interchangeable bell button sets (not included)

• Integrated RFID technology for keyless entry

• Available colors: white, silver, dark gray, black, amber

• Usable with/without function button for mailbox control

• Up to 60hrs backup power supply using DoorMaster (accessory)

Standard Connection: IP Video Door Station with

BellRFID, InfoModule and DoorMaster

Installation and Initial Operation of the BellRFID

Available Bell Button Sets

(for all color variants)

The BellRFID module is installed in the exactly

same manner as the KeypadRFID module. Make

sure that you follow the steps for the dierent

hardware scenarios of the IP Video Door Station

(with/without DoorMaster) as described in the

T24 System Manual Part1

for the KeypadRFID

(see below).

Note: BellRFID and KeypadRFID can only be used

on one MxBus with a later software version of

the camera.

MOBOTIX BellRFID

MX-Bell1-Core

(in IP Video Door Station

triple frame white)

I/O Terminal

Sealing plug

Seal

MxBus terminal

Back view with cover removed

Door

MxBus (YSTY 0.8 mm – max. length: 50m/55yd)

Theft protection (YSTY 0.8 mm – max. length: 50m/55yd)

Door opener, door sensor, lock sensor

(YSTY 0.8 mm – max. length: 50m/55yd)

DoorMaster

RFID cards

for keyless entry included

(1 admin card, 5 user cards)

MX-Bell1-Core

31.578_EN_V2_09/2013

You can use the blue function button at the door station to listen to new mailbox

messages, record new announcements and activate/deactivate the mailbox.

Visitors can leave a message even without the function button. The remaining

mailbox features are easily controlled using the remote station of the door

station (i.e., MOBOTIX App).

Each BellRFID base module contains 6 RFID cards (1admin, 5user cards).

Each button set contains pre-cut name plates made of UV-resistant paper. If

required, you can replace the button sets later on– in the same base module!

In order to conﬁgure the system using BellRFID, the bell buttons are replaced

by a keypad insert, which is delivered with the base module.

The Jones

Family

MX-Bell1-Button-XL1

XL bell button

(no function button)

MX-Bell1-Button-F1

Large bell button

with function button

The Jones

Family

MX-Bell1-Button-F2

2 medium-size bell buttons

with function button

The Jones

Family

Dr. Jones, MD

MX-Bell1-Button-F4

4 small bell buttons

with function button

Cindy Jones

Thomas Jones

The Jones Family

Dr. Jones, MD

MX-Bell1-Button-F3

1 large, 2 small bell buttons

with function button

Cindy Jones

Thomas Jones

Dr. Jones, MD

MX-Bell1-Button-05

5 small bell buttons

(no function button)

Caroline Jones

Cindy Jones

Thomas Jones

The Jones Family

Dr. Jones, MD

Before starting the installation and initial operation, you should download part 1 and 2 of the

T24 System Manual

from the MOBOTIX website

( ).www.mobotix.com> Support> Manuals

If the installation of the IP Video Door Station with BellRFID is not followed by the initial operation right away, MOBOTIX recommends to remove the keypad

insert and to insert the button set before starting the installation. This way, the soft rubber surface of the BellRFID base module is well protected until the

module is brought into service (bell buttons are then replaced by the keypad insert). Note that the base module is weatherproof even without the bell

buttons.

When replacing the button set or exchanging name plates, you need to remove the module from the frame of the IP Video Door Station. Use the

blue MOBOTIX key for unlocking the module. Make sure that you are activating the mechanical theft protection with the red turning knob

in the door station frame only

after

you have ﬁnished the initial operation (see the

Section «Mechanical Anti-Theft Protection Lock»

in the

T24 System Manual Part1

In order to avoid having to remove the module and install it again, you should insert the proper name plates before starting the initial operation.

Use our free-of-charge printing service on in the section! Or use the supplied name plates made from sturdy specialty www.mobotix.com Support

paper and write the names using a UV-resistant marker.

Available Bell

Button Sets

(Accessory) The Jones

Family The Jones

Family

Dr. Jones, MD

Cindy Jones

Thomas Jone s

Dr. Jone s, MD

Cindy Jone s

Thomas Jone s

The Jones Family

Dr. Jones, MD

Cindy Jones

Thomas Jones

The Jones Family

Dr. Jones, MD

Caroline Jones

Cindy Jone s

Thomas Jone s

The Jones Family

Dr. Jones, MD

The Jones

Family

1. Insert the Name Plate(s)

Remove the silicon insert from the button. Recommendation: Take a suitable

tool without a sharp blade, cautiously insert it into the slot, gently press

inward and lift the tool as shown.

Insert the labeled or printed name plate as shown (the arrows at the side

are pointing upwards later on).

Place the silicon insert on top of the name plate, push it into the frame at

the top and at the bottom of the center, then push its sides into the frame.

Make sure that the silicon insert ﬁts ﬂush into the frame of the bell button

as shown to protect the name plate against humidity.

2. Insert the Module into the Door Station

You can use the BellRFID module as an alternative to the KeypadRFID (but

not yet side-by-side) in the frame of an IP Video Door Station. For installing

and wiring the module, follow the same steps as for the KeypadRFID.

Follow the description in the

Section «Installing the T24-KeypadRFID»

of the

T24 System Manual Part1

. Likewise, the other connection variants listed in

the

Section «Overview: Connection and Wiring Diagrams»

(e.g., connecting

an electrical door opener in a system without DoorMaster).

Finish the installation of the BellRFID module by following the steps listed

in the

Section «Finishing the Installation»

of the

T24 System Manual Part1

Similar to the KeypadRFID, the blue and the green status LEDs are ﬂashing

(power supply OK, ready for auto conﬁguration).

Installation Hint

When installing the module, insert it ﬁrst on the right-hand

side. Then use two ﬁngers and press on the left-hand

edge until the module clicks into the frame. Caution: Only

press at the edge, never at the center of the module!

Make sure that the cabling is not pinched and damaged

when installing the module.

3. Execute Auto Conﬁguration

Place the supplied keypad insert into the base module

(push it into the frame at the top, then push the bottom

into the module).

Start the auto conﬁguration of the IP Video Door Station by executing the

steps listed in the

Section «Step1: Performing the Auto Conﬁguration»

the

T24 System Manual Part2

(connect all devices, establish the power

supply and press the bell button of the camera module immediately after

the light and bell buttons are lighting up).

Once you have successfully completed the auto conﬁguration, the white

camera illumination is on and the BellRFID shows the following status:

• The blue and the green status LEDs are ﬂashing.

• The LED of the keypad behind the top right key ( ) is red.OK

Finish the auto conﬁguration by executing the steps listed in the

Section

«Functional Test Part1»

of the

T24 System Manual Part2

4. Enter Super PIN and Conﬁrm

The Super PIN is used to protect the system against misuse and also replaces

the factory default password (“ ”) as the new admin password. The meinsm

password is also used when adding the door station to the MOBOTIX App or

MxEasy, for example (user name is , new password is the admin <Super

PIN>). Select a Super PIN that has a minimum of 8 and a maximum of

16 digits (more and dierent digits make it more secure). For additional

information on the Super PIN, see the

T24 System Manual Part2

Dr.

3 4

Click!

Cindy Jones

Thomas Jones

The Jones Family

Dr. Jones, MD

IndoorOutdoor

For additional information on the other connection variants and for installing,

see the

T24 System Manual Part1

on .www.mobotix.com > Support> Manuals

IP Video Door Station

BellRFID

InfoModule

Cindy Jones

Thomas Jones

The Jones Family

Dr. Jones, MD

Use our free-of-charge on section!Printing Service www.mobotix.com, Support

Weatherproof (IP65)

–30 to +60°C/–22 to +140°F

Produkt Specifikationer

Mærke:	Mobotix
Kategori:	Ikke kategoriseret
Model:	MX-Bell1-Button-F1
Produktfarve:	Grå
Indbygget skærm:	Ingen
Driftstemperatur (T-T):	-30 - 60 °C
Certificering:	IP65
Harmoniseret systemkode (HS):	84719000
Grænseflade:	MxBus
Frekvens:	- kHz