Momcube FS30LMC Manual

Momcube Fryser FS30LMC

Læs nedenfor 📖 manual på dansk for Momcube FS30LMC (16 sider) i kategorien Fryser. Denne guide var nyttig for 27 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/16
MOMCUBE BREAST MILK FREEZER
User Manual
Models:
FS24LMC
FS30LMC
ALFZ36 MC
ALFZ36LMCTBC
VT65MLBIMCADA
BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING
INSTRUCTIONS
Write Model and Serial Numbers
here:
Model: _____________________
Serial No.: __________________
Accucold Division of Felix Storch, Inc.
An ISO 9001:2015 registered company
770 Garrison Avenue
Bronx, NY 10474
www.accucold.com
2
ABOUT THE MOMCUBE FREEZER
MOMCUBE refrigeration products are specially designed for the storage of breast milk in a variety
of facilities, from daycare centers and oce environments to maternity wards and newborn units.
Freezers in the MOMCUBE™ line are designed for the long term storage of frozen milk under the
temperature recommendations suggested by the CDC for healthy, full-term babies. Breast milk
stored in a freezer should be kept at 0ºF (-18ºC) or colder, and should be used within 6 months of
pumping. Breast milk should not be stored for longer than 12 months in a freezer.
In addition to this MOMCUBE™ freezer, Accucold also offers an extensive selection of all-
refrigerators designed to maintain the CDC recommended temperature conditions for freshly
expressed breast milk. These units maintain an interior temperature between 33º and 40ºF, which is
a colder, tighter range than traditional household or dorm style refrigerators.
If you or your facility needs additional storage solutions, we encourage you to visit us online:
More about MOMCUBE: momcube.com
Medical & Life Science Equipment: accucold.com
Residential & Commercial Appliances: summitappliance.com
3
TABLE OF CONTENTS
Equipment Safety 4
Important Safeguards 4-5
Installation Instructions 6- 10
Before Using Equipment 6
Installation of your Equipment 6
Electrical Connection 7
Extension Cord 7
Reversing the Door 8- 10
Operating your Freezer 11
Setting the Temperature Control 11
Care and Maintenance -13 12
Defrosting your Freezer 12
Cleaning your Freezer 12
Vacation Time 12
Moving your Freezer 12
Energy Saving Tips 13
Problems with your Freezer 14
Notes 15
Limited Warranty 16
4
EQUIPMENT SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your unit. Always read
and obey all safety messages.
This is the Safety Alert Symbol. The symbol alerts you to potential hazards that can
kill or injure you and others. All safety messages will follow the Safety Alert Symbol
and either the words "DANGER" or "WARNING".
DANGER means that failure to heed this
safety statement may result in severe
personal injury or death.
WARNING means that failure to heed this
safety statement may result in extensive
product damage, serious personal injury, or
death.
All safety messages will alert you about the potential hazard, tell you how to reduce the chance of
injury, and let you know what can happen if the instructions are not followed.
IMPORTANT SAFEGUARDS
Before the equipment is used, it must be properly positioned and installed as
described in this manual, so read the manual carefully. To reduce the risk of re,
electrical shock or injury when using this equipment, follow basic precautions,
including the following:
Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and
do not use an extension cord.
Replace all panels before operating.
It is recommended that a separate circuit serving only your unit be provided. Use receptacles
that cannot be turned o by a switch or pull chain.
Never clean the equipment parts with ammable uids. These fumes can create a re hazard or
explosion. And do not store or use gasoline or other ammable vapors and liquids in the vicinity
of this or any other pieces of equipment. The fumes can create a re hazard or explosion.
Before proceeding with cleaning and maintenance operations, make sure the power line of the
unit is disconnected.
Do not connect or disconnect the electric plug when your hands are wet.
Unplug the unit or disconnect power before cleaning or servicing. Failure to do so can result in
electrical shock or death.
Do not attempt to repair or replace any part of your unit unless it is specically recommended in
this manual. All other servicing should be referred to a qualied technician.
This unit is CFC- and HFC-free and contains a small quantity of Isobutane (R600a), which is
environmentally friendly but ammable. It does not damage the ozone layer, nor does it increase
the greenhouse eect. care must be taken during transportation and setting up of the unit that no
parts of the cooling system are damaged. leaking coolant can ignite and may damage the eyes.
5
In the event of any damage:
o Avoid open flames and anything that creates a spark,
o Disconnect from the electrical power line,
o Air the room in which the unit isolated for several minutes, and
o Contact the Service Department for advice.
The more coolant there is in a unit, the larger the room it should be installed in. In the event of a
leakage, if the unit is in a small room, there is the danger of combustible gases building up. For
every ounce of coolant, at least 325 cubic feet of room space is required. The amount of coolant
in the unit is stated on the data plate inside the unit. It is hazardous for anyone other than an
Authorized Service Person to carry out servicing or repairs to this piece of equipment.
Take serious care when handling, moving, and using the unit to avoid either damaging the
refrigerant tubing or increasing the risk of a leak.
Replacing component parts and servicing shall be done by factory authorized service personnel
so as to minimize the risk of possible ignition due to incorrect parts or improper service.
FOLLOW WARNING CALLOUTS BELOW
ONLY WHEN APPLICABLE TO YOUR
MODEL
Use two or more people to move and install . Failure to do so can result in back or other unit
injury.
To ensure proper ventilation for your , the front of the unit must be completely unobstructed. unit
Choose a well-ventilated area with temperatures above 60°F (16°C) and below 90°F (32°C). [For
optimal performance, install the unit where the ambient temperature is between 72º and 78ºF
(23º-26ºC). This unit must be installed in an area protected from the elements, such as wind, ]
rain, water spray or drips.
The unit should not be located next to ovens, grills or other sources of high heat.
The unit must be installed with all electrical, water and drain connections in accordance with
state and local codes. A standard electrical supply (115 V AC only, 60 Hz), properly grounded in
accordance with the National Electrical Code and local codes and ordinances, is required.
not kink or pinch the power supply cord of the unit. Do
The size of the fuse (or circuit breaker) should be 15 amperes.
is important that the equipment be leveled in order to work properly. You may need to make It
several adjustments to level it.
All installations must be in accordance with local plumbing code requirements.
Make certain that the pipes are not pinched, kinked or damaged during installation.
Check for leaks after connection.
Never allow children to operate, play with or crawl inside the unit.
use solvent-based cleaning agents or abrasives on the interior. These cleaners may Do not
damage or discolor the interior.
Use this equipment only for its intended purpose as described in this Instruction Manual.
Keep fingers out of the “pinch point” areas. Clea rances between the door and cabinet are
necessarily small. Be careful closing the door when children are in the area.
Risk of child entrapment!
Child entrapment and suocation are not problems of the past. Junked or abandoned appliances are
still dangerous, even if they will “just sit in the garage a few days.”
Before discarding your old refrigerator:
o Take o the doors
o Leave the shelves in place so that children may not easily climb inside
SAVE THESE INSTRUCTIONS
6
INSTALLATION INSTRUCTIONS
Before Using Your Freezer
Remove the exterior and interior packing.
CAUTION: After unpacking you MUST allow this unit to stand upright for at least 2 hours to allow the
lubricant and refrigerant to drain back into the compressor and stabilize. Failure to do so
may adversely aect performance and the lifetime of this unit.
Clean the interior surface with lukewarm water, using a soft cloth.
Installation of your Equipment
The FS24LMC and FS30LMC model numbers are designed for free-standing installation and
indoor only. use
The VT65MLBIMCADA and ALFZ36MC/ALFZ36LMCTBC can be installed either as a free-
standing or built-in unit for indoor use. If it will be built-in, allow at least 3/16” of clear space on
both sides and at the top, and 2at the back. Take care that the air vents at the front are never
covered or blocked in any way.
Do NOT store or install the unit outdoors.
CAUTION: This equipment is designed for the storage of breast milk. We recommend not storing
other food or beverages inside.
Place the freezer on a oor that is strong enough to support it when it is fully loaded. To level the
unit, adjust the front leveling legs.
For the FS24LMC and FS30LMC, allow at least 5 (127mm) of space between the back, top,
and sides of the unit. This allows the proper air circulation to cool the compressor and condenser
for energy saving. The air vent at the front of the unit must never be covered or blocked in any
way.
NOTE: It is recommended that you do not install the unit near an oven, radiator or other heating
source. Direct sunlight may aect the acrylic coating and heat sources may increase
electrical consumption. Don’t install in a location where the temperature will fall below 60°F
(16°C). For best performance, do not install the unit behind a cabinet door or block the base
grille.
Avoid locating the unit in moist areas.
Plug the unit into an exclusive, properly grounded wall outlet. Do not under any circumstances
cut or remove the third (ground) prong from the power cord. Any questions concerning power
and/or grounding should be directed toward a certied electrician or an authorized service
center.
7
Electrical Connection
This unit should be properly grounded for your safety. The power cord of this unit is equipped with a
three-prong plug which mates with standard three-prong wall outlets to minimize the possibility of
electrical shock.
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord
supplied. For personal safety, this equipment must be properly grounded.
This unit requires a standard 115/120 Volt AC 60Hz three-prong grounded electrical outlet. Have ~
the wall outlet and circuit checked by a qualied electrician to make sure the outlet is properly
grounded. When a standard 2-prong wall outlet is encountered, it is your responsibility and
obligation to have it replaced with a properly grounded 3-prong wall outlet.
To prevent accidental injury, the cord should be secured behind the unit and not left exposed or
dangling.
The unit should always be plugged into its own individual electrical outlet which has a voltage rating
that matches the rating label on the unit. This provides the best performance and also prevents
overloading house wiring circuits that could cause a re hazard from overheating. Never unplug the
unit by pulling on the power cord. Always grip the plug rmly and pull straight out from the
receptacle. Repair or replace immediately all power cords that have become frayed or otherwise
damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.
When moving the equipment, be careful not to damage the power cord.
Extension Cord
Because of potential safety hazards under certain conditions, it is strongly recommended that you do
not use an extension cord with this equipment. However, if you must use an extension cord it is
absolutely necessary that it be a UL/CUL-Listed, 3-wire grounding type equipment extension cord
having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at
least 10 amperes.
WARNING
Improper use of the grounded plug can result in the risk of electrical shock. If the power cord
is damaged, have it replaced by a qualied electrician or an authorized service center.
8
Reversing the Door Swing of Your Freezer
The MOMCUBE freezer models are delivered with the door opening from the left-hand side. All of
the models have the capability of reversing the side of the door opening. Check your freezer’s model
number, and use the appropriate instructions for reversing your door. If you have a problem, call
ACCUCOLD Customer Service at 1- -932-4267800 .
For the FS24LMC and FS30LMC models:
1. Remove the door hinge cover from atop the upper door hinge, and set aside.
2. Remove the hinge screws from the upper hinge, and set aside.
3. Carefully lift the door o the lower hinge, and set aside.
4. Remove the lower hinge screws and the lower hinge from the bottom of the cabinet.
5. Move the lower hinge to the opposite side of the cabinet, and attach using the lower hinge
screws.
6. Mount the door onto the lower hinge.
7. Be careful to hold the door against the front of the cabinet, set the upper hinge on the opposite
side of the cabinet, and screw the upper hinge into the door.
8. Replace the door hinge cover.
9
For model numbers ALFZ36MC:
1. Take the hinge cover from the door and remove upper
the screws that hold the top hinge
2. Lift the hinge straight up to free the hinge pin from the
socket in the top of the door
3. Lift the door up and away to free its bottom socket
from the hinge pin
4. Remove the screws to the bottom hinge
5. Remove the decorative caps from the opposite side
and plug the holes from the original side with the
decorative caps
6. Move the bottom hinge to the opposite side and
tighten the screws. Use any lock washers or nuts if
they were used in the original installation.
7. Replace door onto the hinge pin on the bottom hinge.
Place top hinge pin into door. Insert screws into the top hinge.
Note: model ALFZ36LMCTBC is not designed to be reversed after purchase
Installing the Handle
This appliance includes a handle that is not required to operate the unit. To install the handle, follow
the instructions below:
1. Use a screwdriver to remove the screws on the side of door where the handle is to be installed.
2. Align the handle with the screws removed in step # 1. Tighten the screws using a Phillips head
screwdriver until the handle is both ush and secured tightly against the door side. (DO NOT
over-tighten as this will cause damage to the door surface .)
10
For model number VT65MLBIMCADA:
1. Unscrew the lower hinge, and take o the door.
2. Push the kick plate to the right, into the opposite position.
3. Undo the upper hinge fastener, and x it to the opposite side of the housing, where you have
already removed and replaced the fastener with the hole on the opposite side.
4. Put the door on the upper hinge fastener.
5. Fix the lower hinge into the new position.
6. Unscrew the handle, and place it on the opposite side.
7. Some screws are covered with caps. Take o these caps before undoing the screws.
8. Check the gasket. It should not be creased and should seal well.


Produkt Specifikationer

Mærke: Momcube
Kategori: Fryser
Model: FS30LMC

Har du brug for hjælp?

Hvis du har brug for hjælp til Momcube FS30LMC stil et spørgsmål nedenfor, og andre brugere vil svare dig




Fryser Momcube Manualer

Fryser Manualer

Nyeste Fryser Manualer