Morley 20/20 Bad Horsie Manual

Morley Ikke kategoriseret 20/20 Bad Horsie

Læs nedenfor 📖 manual på dansk for Morley 20/20 Bad Horsie (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 27 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
THANK YOU FOR CHOOSING A MORLEY STEVE VAI BAD HORSIE 2 CONTOUR
WAH. YOU NOW OWN THE BEST PEDAL MADE!
Please take a few minutes to familiarize yourself with the features of your new pedal. We hope
you enjoy using it as much as we enjoyed building it.
ABOUT OUR ELECTRO-OPTICAL CIRCUITRY:
An LED (Light Emitting Diode) shines on an LDR (Light Dependent Resistor). A shutter alters light
between the two components controlling functions like Wah, volume and switching. Electro-Optical
design ensures smooth pedal control without unwanted noise typical with potentiometer (pot)
controlled pedals.
ABOUT THE CONNECTIONS:
9V: To ensure noise free operation, ONLY Morley's 9VDC 300 milliamp regulated adapter should
be used
IN: Input jack. Plug instrument into this jack using 1/4" guitar cable.
OUT: Connect amplifier to this jack using a 1/4" guitar cable.
USING AN AC ADAPTER:
All Morley pedals use Morley's 9VDC 300 milliamp regulated adapter. Center pin polarity is
negative. Using a non-regulated adapter could cause a low frequency hum in your
amplifier. Using an adapter with the wrong polarity may damage the pedal.
USING A BATTERY:
All Morley pedals are designed to use one 9V battery when not using an adapter. We suggest you
use a good quality alkaline battery. To prolong battery life, unplug your cord completely from the
input jack when not using the pedal. When the pedal is not used for extended periods, remove the
battery from the pedal. Our Quick Clip” Bettery door allows easy access to battery compartment.
ONE YEAR WARRANTY
All Morley® pedals are warranted for one year with copy of
dated purchase receipt. To obtain warranty service, contact
store where pedal was purchased or email
contact@morleyebtech.com
BAD HORSIE 2 FEATURES (MODEL VAI-2):
·
·
·
·
· SWITCHLESS OPERATION: Simply Step on to engage
Wah and step off to go to bypass.
·
·
·
·· CONTOUR SWITCH: Selects a second Wah mode
·
·
·
·· LEVEL: Adjusts the output of the Wah in Contour
Mode
·
·
·
·· CONTOUR: Adjust the frequncy of the Wah when in
Contour Mode
VAI-2 SPECIFICATIONS:
Power: 9V Battery or 9VDC 300mA regulated (center pin
negative)
Indicator (right): Wah on LED on, Wah off LED off
Indicator (left): Contour Wah on LED on
Dimensions: 9.13" L x 5.88" W x 2.75" H
Current Draw: 12 mA @ 9VDC
Weight: 3.3 lb./ 1.51 kg
www.morleyproducts.com


Produkt Specifikationer

Mærke: Morley
Kategori: Ikke kategoriseret
Model: 20/20 Bad Horsie

Har du brug for hjælp?

Hvis du har brug for hjælp til Morley 20/20 Bad Horsie stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Morley Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Scarlett

Scarlett SC-HC63C107 Manual

9 November 2024
Alpine

Alpine APF-F291320VW Manual

9 November 2024
Klipsch

Klipsch CMS 4.1 Manual

9 November 2024
Alpine

Alpine MQR-III Manual

9 November 2024
Alpine

Alpine DDS-R69K Manual

9 November 2024
Alpine

Alpine KIT-8A3 Manual

9 November 2024
IFM

IFM CR1144 Manual

9 November 2024
IFM

IFM CR1143 Manual

9 November 2024
Auray

Auray SB-52SSB Manual

9 November 2024
Bluetti

Bluetti Charger 1 Manual

9 November 2024