Motorola Talkabout T200 Manual

Motorola Radio Talkabout T200

Læs nedenfor 📖 manual på dansk for Motorola Talkabout T200 (2 sider) i kategorien Radio. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

TALKABOUT ® TWO-WAY RADIO

T2XX SERIES

*MN002392A01*

MN002392A01-AA

MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks

or registered trademarks of Motorola Trademark Holdings, LLC and are used under

license. All other trademarks are the property of their respective owners.

Printed in China

RF Exposure and Product Safety Instructions for

Portable Two-Way Radios General Populated and

Uncontrolled Environments.

ATTENTION:

Before using this radio, refer to the important operating

instructions for safe usage and RF energy awareness and

control for compliance with applicable Standards and

Regulations.

Compliance with RF Exposure Standards

Your Motorola Two-Way radio complies with the following RF

energy exposure standard and guidelines:

• United States Federal Communications Commission,

Code of Federal Regulations; 47 CFR et seq. & FCC.

• Institute of Electrical and Electronic Engineers (IEEE)

C95.1.

• International Commission on Non-Ionizing Radiation

Protection (ICNIRP).

• Ministry of Health (Canada) Safety Code 6 & Industry

Canada RSS-102.

• Australian Communications Authority

Radiocommunications Standard et seq.

• ANATEL ANNEX to Resolution No. 303 of July 2, 2002.

• ANATEL ANNEX to Resolution No. 533 of September 10,

2009.

Transmit and Receive Procedure

Your two-way radio contains a transmitter and a receiver. To

control your exposure and ensure compliance with the general

population/uncontrolled environment exposure limits, always

adhere to the following procedure:

• Transmit no more than 50% of the time.

• To receive calls, release the PTT button.

• To transmit (talk), press the Push-to-Talk (PTT) button in

front of the face.

• Hold the radio in a vertical position with the microphone

(and other parts of the radio including the antenna) at least

one inch (2.5 centimeters) away from the nose or lips.

Keeping the radio at a proper distance is important to

ensure compliance.

Note: RF exposure decreases with increasing distance from the

antenna.

• Body Worn Operation. When worn on the body, always

place the radio in a Motorola-approved clip, holder,

holster, case or body harness for this product.

Please refer to the following websites for more information on

what RF energy exposure is and how to control your exposure

to assure compliance with established RF exposure limits:

• http://www.fcc.gov/oet/rfsafety/rf-faqs.html

• www.who.int/en/

• http://responsibility.motorolasolutions.com/index.php/

downloads/dow07-rfexposureassessmentstand/

Two-way Radio Operation

• Use only Motorola-approved supplied or replacement

antennas, batteries, and audio accessories. Use of non-

Motorola-approved antennas, batteries, and wired or

wireless accessories may exceed the applicable RF

exposure guidelines (iEEE, ICNIRP or FCC).

• For a list of Motorola-approved accessories for your radio

model, visit the following website: http://

www.motorolasolutions.com/TalkaboutAccessories.

Electromagnetic Interference/Compatibility

Note: Nearly every electronic device is susceptible to

electromagnetic interference (EMI) if inadequately

shielded, designed or otherwise configured for

electromagnetic compatibility.

This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received,

including interference that may cause undesired

operation.

This device complies with Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference received,

including interference that may cause undesired operation

of the device.

Facilities

To avoid electromagnetic interference and/or compatibility

conflicts, turn off your radio in any facility where posted notices

instruct you to do so. Hospitals or health care facilities may be

using equipment that is sensitive to external RF energy.

Aircraft

When instructed to do so, turn off your radio when onboard an

aircraft. Any use of a radio must be in accordance with

applicable regulations per airline crew instructions.

Medical Devices – Pacemakers, Defibrillators or other

Implanted Medical Devices

Persons with pacemakers, Implantable cardioverter-

defibrillators (ICDs) or other active implantable medical devices

(AIMD) must:

• Consult with their physicians regarding the potential risk of

interference from radio frequency transmitters, such as

portable radios (poorly shielded medical devices may be

more susceptible to interference).

• Turn the radio OFF immediately if there is any reason to

suspect that interference is taking place.

• Do not carry the radio in a chest pocket or near the

implantation site, and carry or use the radio on the

opposite side of their body from the implantable device to

minimize the potential for interference.

Hearing Aids

Some digital wireless radios may interfere with some hearing

aids. In the event of such interference, you may want to consult

your hearing aid manufacturer to discuss alternatives.

Other Medical Devices

If you use any other personal medical device, consult the

manufacturer of your device to determine if it is adequately

shielded from RF energy. Your physician may be able to assist

you in obtaining this information.

Use of Communication Devices While Driving

Always check the laws and regulations on the use of radios in

the areas where you drive.

• Give full attention to driving and to the road.

• Use hands-free operation, if available.

• Pull off the road and park before making or answering a

call, if driving conditions or regulations so require.

For Vehicle With Air Bags

Refer to the vehicle manufacturer’s manual prior to installation

of electronic equipment to avoid interference with air bag wiring.

Do not place a portable radio in the area over an air bag or in

the air bag deployment area. Air bags inflate with great force. If

a portable radio is placed in the air bag deployment area and the

air bag inflates, the radio may be propelled with great force and

cause serious injury to occupants of the vehicle.

Potentially Explosive Atmosphere

Turn off your radio prior to entering any area with a potentially

explosive atmosphere. Only radio types that are especially

qualified must be used in such areas as “Intrinsically Safe”. Do

not remove, install or charge batteries in such areas. Sparks in a

potentially explosive atmosphere can cause an explosion or fire

resulting in bodily injury or even death.

Note:The areas with potentially explosive atmosphere referred

to above include fueling areas such as below decks on

boats, fuel or chemical transfer or storage facilities, areas

where the air contains chemicals or particles (such as

grain, dust or metal powders) and any other area where

you would normally be advised to turn off your vehicle

engine. Areas with potentially explosive atmospheres are

often – but not always posted.

Blasting Caps and Areas

To avoid possible interference with blasting operations, turn off

your radio when you are near electrical blasting caps, in a

blasting area, or in areas posted “Turn off two-way radios”. Obey

all signs and instructions.

Operational Cautions

Antennas

Do not use any portable radio that has a damaged antenna.

If a damaged antenna comes into contact with your skin, a

minor burn can result.

Batteries

All batteries can cause property damage and/or bodily injury

such as burns if a conductive material touches exposed

terminals. The conductive material may complete an electrical

circuit (short circuit) and become hot.

• Exercise care when removing NiMH or AA batteries. Do

not use sharp or conductive tools to remove these

batteries.

• Exercise care in handling any charged battery, particularly

when placing it inside a pocket, purse or other container

with metal objects.

• Do not discard your battery in a fire.

• Do not replace the battery in any area labeled “Hazardous

Atmosphere”. Any sparks created in a potentially

explosive atmosphere can cause explosion or fire.

• Do not disassemble, crush, puncture, shred or otherwise

attempt to change the form of your battery.

• Do not dry a wet battery or damp battery with an appliance

or heat source, such as a hair dryer or microwave oven.

• If the radio battery contact area has been submerged in

water, dry and clean the battery contacts before attaching

the battery to the radio.

Battery Charger Safety Instructions:

Save these Instructions

1. Turn the radio off when charging the battery.

2. Do not expose the charger to outside environment.

Chargers must only be used indoors.

3. Do not operate or disassemble the charger. Do not use a

charger that has been dropped or damaged in any way.

4. Never alter the AC cord or plug provided with the unit. If

the plug will not fit the outlet, have the proper outlet

installed by a qualified electrician. An improper condit ion

can result in a risk of electric shock.

5. To reduce the risk of damage to the cord or plug, pull the

plug rather than the cord when disconnecting the charger

from the AC receptacle.

6. To reduce the risk of electric shock, unplug the char ger

from the outlet before attempting any maintenance or

cleaning.

7. Use of an attachment not recommended or sold by

Motorola Solutions may result in a risk of fire, electr ic

shock or personal injury.

8. Make sure the cord is located so it will not be stepped on,

tripped over or subjected to damage or stress.

9. An extension cord must not be used unless absolute ly

necessary. Use of an improper extension cord could result

in a risk of a fire and/or electric shock. If an extension cord

must be used, make sure that:

• The pins on the plug of the extension cord are the same

number, size and shape as those on the plug of the

charger.

• The extension cord is properly wired and in good

condition.

• The extension cord size is 18 AWG for lengths up to 100

feet, and 16 AWG for lengths up to 150 feet.

10. The supply cord of the AC adaptor cannot be replaced. If

the cord is damaged, call customer service.

USA

Use of GMRS frequencies is subject to the Rules and

Regulations of the Federal Communications Commission

(FCC).

The FCC requires that all operators using GMRS frequencies

obtain a radio license before operating their equipment. To

obtain the FCC forms, please visit the FCC website at

wireless.fcc.gov/uls/index.htm?job=home to source form 605

and 159, which includes all the instructions you will need.

If you wish to have the document faxed or mailed, or if you have

questions, please use the following contact information:

Canada

Use of Motorola radio in Canada is subject to the rules &

regulations of Industry Canada (IC). IC requires no license when

operated in Canada.

Changes or modifications not expressly approved by Motorola

Solutions may void the user authority granted by the IC/FCC to

operate this radio and must not be made. To comply with IC/

FCC requirements, transmitter adjustments must be made only

by or under the supervision of a person certified as technically

qualified to perform transmitter maintenance and repairs in the

private land mobile and fixed services as certified by an

organization representative of the user of those services.

Replacement of any transmitter component (crystal,

semiconductor, etc) not authorized by the IC/FCC equipment

authorization for this radio could violate IC/FCC rules.

Note: Use of this radio outside the country where it was

intended to be distributed is subject to government

regulations and may be prohibited.

Mexico

Use of GMRS frequencies is subject to the Rules and

Regulations of the Federal Communications Institute (IFT)

requires that all operators using GMRS frequencies obtain a

permit before operating their equipment. To obtain a permit from

the IFT, the user must proceed in accordance with Articles 14

and 15 of the Federal Telecommunications Law. Consult your

local IFT office for more information: www.ift.org.mx

Uruguay

Use of GMRS frequencies is subject to the Rules and

Regulations of the Regulatory Unit Communications Services

(URSEC). URSEC requires that all operators using GMRS

frequencies obtain a permit before operating their equipment.

The authorization shall depend on the channel availability at the

time the authorization is requested. To obtain a permit from

URSEC, consult your local URSEC office for more information:

www.ursec.gub.uy.

Panama

The Republic of Panama does not require authorization to use

FRS/GMRS radio equipment frequencies.

Chile

Servicio de Banda Local UHF frequency use is subject to

SUBTEL Resolution 1.261 and Resolution 52 Exenta. A license

is required for use in Chile. To obtain a Banda Local end-user

license:

1. Fill out the required application form to request Local Band

service.

a. It is available on the SUBTEL website:

http://www.subtel.gob.cl/ index.php?option=com_ content&view

=article&id=1388&Itemid=2087

b. It is also available at the SUBTEL offices:

Subsecretaría de Telecomunicaciones

Unidad de Licencias y Permisos

Lorenzo Gotuzzo N°124, piso 6

Santiago, Chile

Tel. (56-2) 421 3634

2. Present this form with your ID at the above location.

3. Consult the SUBTEL offices for applicable fees.

For more information, consult SUBTEL at www.subtel.cl or call

their offices at the telephone number listed above.

Colombia

Operacion itinerante de baja potencia frequency use is subject

to CRC Resolución 002190 de 2003. No license is required for

use in Colombia. Consult CRC at www.crcom.gov.co for more

information.

Peru

Colectivo Familiar frequency use is subject to MTC RVM

388-200-MTC/15.03 and FCC (FRS), Part 95B. No license is

required for use in Peru. Consult MTC Peru at www.mtc.gob.pe

for more information.

Argentina

Uso Familiar frequency use is subject to CNC Resolution SC

No. 2750/98. No license is required for use in Argentina.

Consult the AFTIC at http://www.aftic.gob.ar/ for more

information.

Brazil

The frequency general use is subject to the Annex to Resolution

506 Section XIV - Radio Communication Equipment General

Purpose. It is not required use license in Brazil. See the

ANATEL site for more information: http://www.anatel.gov.br/

Portal/exibirPortalInternet.do

Installing the Batteries

Discard the retailer tag (loose in one of the battery

compartments), before installing batteries.

Each radio can use either 1 NiMH rechargeable battery pack or

3 AA alkaline batteries and beeps when the batteries are low.

Installing the NiMH Rechargeable Battery Pack

(Optional Accessory)

1. Take the belt clip off.

2. With the back of the radio facing you, lift the battery cover

latch up and remove the cover.

3. Insert the NiMH battery pack by following the instruction

on the battery pack. (The ribbon must be underneath the

battery pack and must wrap around the right side of the

pack for easy removal).

4. Close the battery cover firmly.

Installing the Three AA Alkaline Batteries

1. Take the belt clip off.

2. With the back of the radio facing you, lift the battery cover

latch up and remove the cover.

3. Insert the three AA Alkaline batteries with + and – polarity

as shown inside. (The ribbon must be underneath the AA

alkaline batteries and must wrap around the right side of

the batteries).

4. Close the battery cover firmly.

Radio Battery Meter

The radio battery icon shows the battery charge level, from full

to empty . When the radio has one segment left,

the radio chirps periodically or after releasing the PTT button

(Low Battery Alert).

Removing the NiMH Battery Pack

1. Turn the radio off.

2. With the back of the radio facing you, lift the battery cover

latch up and remove the cover.

3. Remove the NiMH battery pack by pulling the ribbon

attached to the radio.

4. Close the battery cover firmly.

Removing the Three AA Alkaline Batteries

1. Turn the radio off.

2. With the back of the radio facing you, lift the battery cover

latch up and remove the cover.

3. Gently remove each alkaline battery by pulling the ribbon

attached to the radio.

4. Close the battery cover firmly.

Note:

• Exercise care when removing NiMH or AA batteries. Do

not use sharp or conductive tools to remove either of

these batteries.

• Remove the batteries before storing your radio for

extended periods of time. Batteries corrode over time and

may cause permanent damage to your radio.

Battery Capacity Maintenance

1. Charge the NiMH batteries once every 3 months when not

in use.

2. Before placing the radio in storage, remove the battery.

3. Store the NiMH batteries in temperature between -20 °C to

35 °C and in low humidity. Avoid damp conditions and

corrosive materials.

Using the Micro-USB Charger

The micro-USB charger is a handy port that allows you to

conveniently charge your NiMH battery pack.

1. Make sure your radio is turned OFF.

2. Plug the micro-USB cable into the micro-USB charging

port on your radio. Connect the other end of the micro-

USB charger to wall power outlet.

3. An empty battery will be fully charged in 12 hours.

4. The battery meter on LCD will move to indicate the battery

is charging.

Note:

• It is recommended to power OFF your radio while

charging. However, if power is turned on while charging,

you may not be able to transmit a message if the battery is

completely empty. Allow time for the battery to charge to 1

bar before attempting to transmit a message.

• When moving between hot and cold temperatures, do not

charge the NiMH battery pack until the battery

temperature acclimates (usually about 20 minutes).

• For optimal battery life, remove the radio from the charger

within 16 hours. Do not store the radio while connected to

the charger.

Attaching and Removing the Belt Clip

1. Attach the belt clip to the back of the radio until the clip

clicks in place.

2. Attach the belt clip to pocket or belt strap until the clip

clicks in place.

To Remove

1. Push the release tab on top of the belt clip to release the

latch.

2. Pull the belt clip away from the back of the radio.

Turning your Radio On and Off

1. Press and hold on the button to turn your radio ON/

OFF. In the ON position, the radio chirps and briefly shows

all feature icons available on the radio.

2. The display screen then shows the current channel, code

and all features that are enabled. The radio is in

Two-Way mode.

Setting the Volume

Press and hold for three seconds to listen to volume level.

1. First press either or to trigger volume change. You

will see current volume level on screen.

2. Press to increase the volume. Press to decrease

the volume.

3. When the volume reached level 0 the mute icon

appears permanently on screen.

Do not hold the radio close to your ear. If the volume is set to an

uncomfortable level, it could hurt your ear.

To communicate, all radios in your group must be set to the

same channel and Interference Eliminator Code.

1. To talk, press and hold the PTT button. When transmitting,

icon blinks (only on radio with weather

mode feature) and is shown.

2. When you are finished talking, release the PTT button.

3. When receiving, icon blinks (only on radio

with weather mode feature) and is shown.

For maximum clarity, hold the radio one inch away from your

mouth and speak directly into the microphone. Do not cover the

microphone while talking.

Talk Range

Your radio is designed to maximize performance and improve

transmission range. Do not use the radios closer than five feet

apart.

Monitor Button

Pressing and holding for three seconds allows you to listen

to the volume level of the radio when you are not receiving. You

can also press to check for activity on the current channel

before you talk.

Push-to-Talk Timeout Timer

To prevent accidental transmissions and save battery life, the

radio emits a continuous warning tone and stops transmitting if

you press the PTT button for 60 continuous seconds.

Mode Button (Only on Radio with Weather Mode

Feature)

By pressing “mode” button, the user will be seamlessly

switching between two-way and weather mode. When radio is in

two-way mode, will be shown. When radio is in

weather mode, will be shown. Corresponding

setting and information will be shown on the LCD.

Selecting the Channel

Each country model has different number of channels and

frequencies. See the “Channels and Frequencies” table on

overleaf for details.

1. With the radio on, press one time until the channel

number starts to flash.

2. Press or and select an unused or quiet channel.

An extended press of or allows you to scroll

through the channels rapidly.

Safety and General Information

For a fax:

Contact the Fax-On-

Demand system

For mail service:

Call the FCC Forms

Hotline

If you have questions

about the FCC License:

Call the FCC

1-202-418-0177 1-800-418-FORM (3676) 1-888-CALL-FCC

(225-5322)

Licensing Information

Control Buttons

MODE

Push-to-Talk

Power On/Off/

Mode Switch

Call Tone

Screen

Scan/Monitor

Menu/Lock

Accessory Port

Speaker

Micro-USB

Charging Port

Microphone

Display Screen Guide

Numbers for Channel

Numbers for Codes,

Call Tone

Battery Meter

Weather Alert

Lock

Roger Tone

Call Tone

Keypad Tone

Mute

Status (transmit/

receive)

Scan

iVOX / VOX

Getting Started

MODE

Talking and Listening

Menu Options

Produkt Specifikationer

Mærke:	Motorola
Kategori:	Radio
Model:	Talkabout T200

Har du brug for hjælp?

Hvis du har brug for hjælp til Motorola Talkabout T200 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Radio Motorola Manualer

Motorola T50 Manual

27 September 2024

Motorola APX 8000XE Manual

24 September 2024

Motorola T605 Manual

22 September 2024

Motorola Talkabout T383 Manual

10 September 2024

Motorola APX 8000HXE Manual

31 August 2024

Motorola MOTOTRBO R7 Manual

30 August 2024

Motorola MOTOTRBO Ion Manual

30 August 2024

Motorola Talkabout T465 Manual

6 August 2024

Motorola Talkabout T605 Manual

5 August 2024

Motorola CLP1010 Manual

2 August 2024

Radio Manualer

Nyeste Radio Manualer

TechniSat Sternradio IR 2 Manual

1 December 2024

Roberts Blutune 300L Manual

24 November 2024

Ferguson Regent i450S Manual

20 November 2024

Reflexion HRA-1255DAB Manual

20 November 2024

Majority MP3 Pro Manual

19 November 2024

Noxon iRadio 500 CD Manual

17 November 2024

GPX R116B Manual

17 November 2024

Technics OTTAVA f SC-C70MK2 Manual

16 November 2024

Soundmaster DAB85 Manual

16 November 2024

Muse M-928 FB Manual

15 November 2024