Motorola Talkabout T482 Manual

Motorola Radio Talkabout T482

Læs nedenfor 📖 manual på dansk for Motorola Talkabout T482 (2 sider) i kategorien Radio. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

TALKABOUT ® EMERGENCY

PREPAREDNESS TWO-WAY

RADIO T48X Series

*MN001399A01*

MN001399A01-AG

MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks

or registered trademarks of Motorola Trademark Holdings, LLC and are used under

license. All other trademarks are the property of their respective owners.

Printed in

For More Information

For further information, you may call Motorola Solutions at

1-800-448-6686 (Canada and U.S.), or visit us on the Internet at

www.motorolasolutions.com/talkabout.

Caution

Before using this radio, read this booklet which contains

important operating instructions.

For information on product details, brochures, user manuals and

approved accessories. Please refer to

www.motorolasolutions.com.

Compliance with RF Exposure Standards

National and international regulations require manufacturers to

comply with the RF energy exposure limits for portable two-way

radios before they can be marketed. Your Motorola Solutions

two-way radio is designed, manufactured, and tested to comply

with all applicable national and international regulations for

human exposure to radio frequency electromagnetic energy.

RF Energy Exposure Awareness and Control Information

and Operational Instructions for General Population and

Uncontrolled Environment Use

For more information on what RF energy exposure is, see the

following websites:

• https://www.fcc.gov/

• http://www.who.int/peh-emf/project/en/

•http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf11467.html

•http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01904.html

For additional information, see

https://www.motorolasolutions.com/en_us/about/company-

overview/corporate-responsibility/governance-and-policies.html

Class B Digital Device

For a Class B digital device or peripheral, the instructions

furnished the user shall include the following or similar

statement, placed in a prominent location in the text of the

manual:

Note:This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions,

may cause harmful interference to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

Operating Instructions

• Transmit no more than 50% of the time. To transmit (talk),

press the Push-To-Talk (PTT) button. To receive calls, release

the PTT button.

• Hold the radio in a vertical position in front of the face with the

microphone (and other parts of the radio including the

antenna) at least 1 in. (2.5 cm) away from the nose or lips.

Antenna should be kept away from the eye.

• When worn on the body, always place the radio in a Motorola

Solutions-approved clip, holder, holster, case, or body

harness for this product.

• DO NOT hold the antenna when the radio is transmitting.

• DO NOT use any portable radio that has a damaged antenna.

If a damaged antenna comes into contact with your skin, a

minor burn can result.

• To ensure continued compliance with applicable RF exposure

limits, use only Motorola Solutions-approved, supplied or

replacement antennas, batteries, and accessories.

• For a list of Motorola Solutions-approved accessories please

refer to your user manual or visit www.motorolasolutions.com

Acoustic Safety

Exposure to loud noises from any source for extended periods

of time may temporarily or permanently affect your hearing. The

louder the volume of the radio, the sooner your hearing will be

affected. Hearing damage from loud noise is sometimes

undetectable at first, and can have a cumulative effect.

To protect your hearing, follow these precautions:

• Use the lowest volume necessary to do your job.

• Turn up the volume only if you are in noisy surroundings.

• Turn down the volume before putting on a headset or

headphones.

• Limit the amount of time you use a headset or headphones at

high volume.

• When using the radio without a headset or headphones, do

not place the speaker of the radio directly against your ear.

Medical Devices

If you use a personal medical device, such as a pacemaker or

hearing aid, consult the manufacturer of your device to

determine if it is adequately shielded from RF energy. Your

physician may be able to assist you in obtaining this information.

Operational Warnings

The following explains the operational warnings:

For Vehicle With Air Bags

Potentially Explosive Atmospheres

Blasting Caps and Blasting Areas

Batteries

• Charge your battery using the approved Motorola Solutions

charger.

• Use the battery in accordance with its water and/or dust

Ingress Protection (IP) rating.

• Do not discard your battery into a fire.

• Do not replace the battery in any area labeled “Hazardous

Atmosphere”.

• Do not disassemble, crush, puncture, shred, or otherwise

attempt to change the form of your battery.

• Do not dry a wet or damp battery with an appliance or heat

source, such as a hair dryer or microwave oven.

• Do not allow conductive material such as jewelry, keys, or

beaded chains to touch exposed battery terminals.

Do Not Substitute Options or Accessories

The Motorola Solutions communications equipment certified as

intrinsically safe by the approving agency (FM, UL, CSA,

CENELEC) is tested as a complete system which consists of the

listed agency approved portable, approved battery, and

approved accessories or options, or both. This approved

portable and battery combination must be strictly observed.

There must be no substitution of items, even if the substitute

has been previously approved with a different Motorola

Solutions communications equipment unit. Approved

configurations are listed by the approving agency (FM, UL,

CSA, CENELEC).

The Intrinsically Safe Approval Label affixed to radio refers to

the intrinsically safe classification of that radio product, and the

approved batteries that can be used with that system.

The manual PN referenced on the Intrinsically Safe Approval

Label identifies the approved accessories and or options that

can be used with that portable radio unit.

Using a non-Motorola Solutions-intrinsically safe battery and/or

accessory with the Motorola Solutions-approved radio unit will

void the intrinsically safe approval of that radio unit.

European Union (EU) Waste of Electrical and

Electronic Equipment (WEEE) Directive

Supplier’s Declaration of Conformity

Notice to Users (FCC and Industry Canada)

This device complies with Part 15 of the FCC rules and Industry

Canada's license-exempt RSS's per the following conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including

interference that may cause undesired operation.

• Changes or modifications made to this device, not expressly

approved by Motorola Solutions, could void the authority of

the user to operate this equipment.

USA (FCC)/CANADA

According to FCC Part 95, FRS devices do not require a

license. Use of Motorola radio in Canada is subject to the rules

regulations in ISED RSS 210 and do not require a license.

Changes or modifications not expressly approved by Motorola

Solutions may void the user authority granted by the FCC or

ISED to operate this radio and should not be made. To comply

with FCC or ISED requirements, transmitter adjustments should

be made only by or under the supervision of a person certified

as technically qualified to perform transmitter maintenance and

repairs in the private land mobile and fixed services as certified

by an organization representative of the user of those services.

Replacement of any transmitter component (crystal,

semiconductor, etc) not authorized by the FCC or ISED

equipment authorization for this radio could violate FCC or ISED

rules.

Note:Use of this radio outside the country where it was intended

to be distributed is subject to government regulations and

may be prohibited.

Weatherproof

This radio is weatherproof to IP-54 standards. It is dust/

splashproof from any direction. The radio is resistant to water

and rain splashes only when the battery cover, headset

accessory port, and micro-USB ports are sealed. Open the

battery compartment door or headset port cover only when the

radio is dry. Use of a headset accessory should be in dry

environments only.

The micro-USB adaptor is not waterproof. Do not expose to rain

or snow. Charge the radios only in a dry location. Do not charge

wet radios. The battery door must be tightly closed with the

screw to maintain the weatherproof seal of the radio.

Installing the Batteries

Each radio can use either 1 NiMH rechargeable battery pack or

3 AA alkaline batteries and beeps when the batteries are low.

Installing the NiMH Rechargeable Battery Pack

(Optional Accessory)

1. Turn the radio off.

2. With the back of the radio facing you, loosen the retaining

screw on the battery door and open the cover.

3. Remove the NiMH battery pack from the clear plastic bag

(do not disassemble or unwrap the battery pack).

4. Insert the NiMH battery pack with the diagram facing you.

(The ribbon should be underneath the battery pack and

should wrap around the right side of the pack for easy

removal).

5. Close the battery cover and tighten the retaining screw on

the battery cover.

Installing the Three AA Alkaline Batteries

1. Turn the radio off.

2. With the back of the radio facing you, lift the battery cover

latch up and remove the cover.

3. Insert the three AA Alkaline batteries with + and – polarity as

shown inside. (The ribbon should be underneath the AA

alkaline batteries and should wrap around the right side of

the batteries).

4. Close the battery cover and tighten the retaining screw on

the battery cover.

Radio Battery Meter

The radio battery icon shows the battery charge level, from full

to empty . When the radio has one segment left,

the radio chirps periodically or after releasing the PTT button

(Low Battery Alert).

Removing Battery Door and Belt Clip

1. Use your thumb or index finger to unlatch the belt clip tab,

use thumb on another hand to push up the belt clip.

2. Use a coin to unscrew the battery door screw lock.

Removing the NiMH Battery Pack

1. Turn the radio off.

2. With the back of the radio facing you, loosen the retaining

screw on the battery door and open the cover.

3. Remove the NiMH battery pack by pulling the ribbon

attached to the radio.

4. Close the battery cover and tighten the retaining screw on

the battery door.

Removing the Three AA Alkaline Batteries

1. Turn the radio off.

2. With the back of the radio facing you, loosen the retaining

screw on the battery door and open the cover.

3. Gently remove each alkaline battery by easing each battery

out individually.

4. Close the battery cover and tighten the retaining screw on

the battery door.

Note:

• Exercise care when removing NiMH or AA batteries. Do not

use sharp or conductive tools to remove either of these

batteries.

• Remove the batteries before storing your radio for extended

periods of time. Batteries corrode over time and may cause

permanent damage to your radio.

Battery Capacity Maintenance

1. Charge the NiMH batteries once every 3 months when not in

use.

2. Before placing the radio in storage, remove the battery.

3. Store the NiMH batteries in temperature between -20 °C to

35 °C and in low humidity. Avoid damp conditions and

corrosive materials.

Using the Micro-USB Charger

The micro-USB charger is a handy port that allows you to

conveniently charge your NiMH battery pack.

1. Make sure your radio is turned OFF.

2. Plug the micro-USB cable into the micro-USB charging port

on your radio.

3. Connect the USB charger to a nearby and easily accessible

wall power outlet.

4. An empty battery will be fully charged in 14 hours.

5. The battery meter on LCD will move to indicate the battery is

charging.

Note:

• When moving between hot and cold temperatures, do not

charge the NiMH battery pack until the battery temperature

acclimates (usually about 20 minutes).

Using the Desk/Wall Stand

This stand allows for convenient placement during charging (on

desk or hung on wall). Cable management can be achieved via

cavity at bottom of stand.

1. Determine the required cable length.

2. Place rolled up cable with cable tie into stand around the two

latches following markings for correct orientation.

Note: For alternate lengths, wrap cable around approximately 3

fingers for correct loop size.

3. Assemble bottom cover on stand.

Quiet Charge

In order to ensure that your radio is always charged and on

alert, we recommend that you leave the radio plugged in and

turned on. The Quiet Charge feature allows you to disable the

reception from regular two-way calls while still receiving weather

alerts and receive and transmit emergency alerts.

To activate quiet charge:

1. Press 9 times until appears on the display. The

current setting will flash.

2. Press or to select On or Off.

3. Press the PTT button or to set.

Note: Turn Quiet Charge off when you want to have full two-way

call functionality (receive all activity on your channel).

Attaching and Removing the Belt Clip

1. Attach the belt clip to the Talkabout plate at the back of the

radio until the clip clicks in place.

2. Attach the belt clip to pocket or belt strap until the clip clicks

in place.

To Remove

1. Pull the release tab on top of the belt clip to release the latch.

2. Push the belt clip with the other hand towards the top of the

radio.

Turning your Radio On and Off

Turn clockwise to turn the radio on and counterclockwise to

turn the radio off.

1. In the ON position, the radio chirps and briefly shows all

feature icons available on the radio.

2. The display screen then shows the current channel, code

and all features that are enabled. The radio is now in

Two-Way mode.

Setting the Volume

Press and hold for three seconds while rotating until you

reach a comfortable listening level.

1. Rotate clockwise to increase the volume.

2. Rotate counterclockwise to decrease the volume.

Do not hold the radio close to your ear. If the volume is set to an

uncomfortable level, it could hurt your ear.

To communicate, all radios in your group must be set to the

same channel and Interference Eliminator Code.

1. To talk, press and hold the PTT button. When transmitting,

icon blinks and is shown. If it is a high

power transmission, is shown. If it is a low power

transmission, is shown.

2. When you are finished talking, release the PTT button.

3. When receiving, icon blinks and is shown.

If it is a high power channel, is shown. If it is a low power

channel, is shown.

For maximum clarity, hold the radio two to three inches away

from your mouth and speak directly into the microphone. Do not

cover the microphone while talking.

Note: The use of an emergency two-way radio is best when

other people in your community are using two-way radios

as well. Talk to neighbors and friends nearby and suggest

to check in on each other when disaster strikes.

Talk Range

Your radio is designed to maximize performance and improve

transmission range. Do not use the radios closer than five feet

apart.

Power Boost

To boost your radio’s power up to high power, press the top

portion of the PTT button when talking. If you know your party is

close by, you can conserve the energy of your battery by

pushing the lower part of the PTT button to use less power.

Note: If you are on an FRS only channel (see “Channels and

Frequencies”) the radio will only use low power when

either portion of the PTT button is pressed.

Power Boost is not applicable for model T400.

Monitor Button

Pressing and holding for three seconds allows you to listen

to the volume level of the radio when you are not receiving. This

allows you to adjust the volume, if necessary. You can also

press to check for activity on the current channel before you

talk.

Push-to-Talk Timeout Timer

To prevent accidental transmissions and save battery life, the

radio emits a continuous warning tone and stops transmitting if

you press the PTT button for 60 continuous seconds.

Mode Button

By pressing “mode” button, the user will be seamlessly

switching between two-way, weather mode and FM mode.

When radio is in two-way mode, will be shown.

When radio is in weather mode, will be shown.

Corresponding setting and information will be shown on the

LCD.

Selecting the Channel

Your radio has 22 channels. The channel is the frequency the

radio uses to transmit. Channels 8-14 are FRS 0.5 watt only and

all other channels are GMRS. (See the “Channels and

Frequencies” table on overleaf for details).

1. With the radio on, press 1 time until the channel number

starts to flash. When the radio is on a 0.5 watt channel,

display shows . When the radio is on a 1.5 watts

channel, display shows . The current channel flashes.

2. Press or and select an unused or quiet channel.

3. Press the PTT button to save the channel setting or to

continue set up.

Selecting the Interference Eliminator Code

Interference Eliminator Codes help minimize interference by

blocking transmissions from unknown sources. Your radio has

121 Interference Eliminator Codes. Codes 1 – 38 are standard

analog codes that appear on other FRS/GMRS radios. Codes

39 – 121 are additional digital codes added for superior

interference protection. 0 is the off position, no analog or digital

codes are enabled.

To set the code for a channel:

1. Press 2 times until the code starts to flash.

2. Press or to select the code.

Safety and General Information

Warning:

• Refer to vehicle manufacturer's manual prior to

installation of electronic equipment to avoid

interference with air bag wiring.

• DO NOT place a portable radio in the area over an

air bag or in the air bag deployment area. Air bags

inflate with great force. If a portable radio is placed in

the air bag deployment area and the air bag inflates,

the radio may be propelled with great force and cause

serious injury to occupants of the vehicle.

Warning:

• Use of a radio that is not intrinsically safe in a

potentially explosive atmosphere could result in a

serious injury, or death. You should only use a

certified Intrinsically Safe radio in potentially

explosive atmospheres.

• Explosive atmospheres refer to hazard classified

locations that may contain hazardous gas, vapors,

dusts, such as fueling areas below decks on boats,

fuel, or chemical transferor storage facilities, and

areas where the air contains chemicals or particles

such as grain, dust, or

metal powders. Areas with potentially explosive

atmospheres are often, but not always, posted.

• Turn off your radio prior to entering any area with a

potentially explosive atmosphere unless it is a radio

type specifically certified for use in hazardous

location areas.

• DO NOT remove, install, or charge batteries in such

areas, or remove or install antennas. Sparks in a

potentially explosive atmosphere can cause an

explosion or fire resulting in bodily injury or even

death.

Warning: To avoid possible interference with blasting

operations, turn off your radio when you are near

electrical blasting caps, in a blasting area, or in areas

posted: “Turn off two-way radio.” Obey all signs and

instructions.

Use only Motorola Solutions approved batteries.

Risk of explosion if the battery is replaced by an

incorrect type.

W A R N I N G

The European Union's WEEE directive requires that

products sold into EU countries must have the

crossed out trash bin label on the product (or the

package in some cases). As defined by the WEEE

directive, this cross-out trash bin label means that

customers and end-users in EU countries should not

dispose of electronic and electrical equipment or

accessories in household waste. Customers or end-

users in EU countries should contact their local

equipment supplier representative or service centre

for information about the waste collection system in

their country.

Supplier’s Declaration of Conformity

Per FCC CFR 47 Part 2 Section 2.1077(a)

Responsible Party

Name: Motorola Solutions, Inc.

Address: 2000 Progress Pkwy, Schaumburg, Il.

60196.

Phone Number: 1-800-927-2744

Hereby declares that the product:

Model Name: T482

conforms to the following regulations:

FCC Part 15, subpart B, section 15.107(a), 15.107(d),

and section 15.109(a)

FCC Licensing Information

Control Buttons

MODE

Volume/Power

Push-to-Talk (High)

Mode Switch

Call Tone

Emergency

Button

Screen

Scan/Monitor

Menu/Lock

Flashlight LED

Accessory Port

Flashlight Button

Speaker

Microphone

Micro-USB

Charging Port

Push-to-Talk (Low)

Display Screen Guide

Numbers for Channel,

Call Tone

Numbers for Codes,

FM Radio Frequency

Battery Meter

Weather Alert

LockNoise Filtering

Scan

Call Tone

iVOX / VOX

Battery Save

Roger Tone

Keypad Tone

Power (high-low)

Status (transmit/

receive)

Quiet Charge

Modes

Getting Started

Talking and Listening

Menu Options

1 2 3 4 5 6

Produkt Specifikationer

Mærke:	Motorola
Kategori:	Radio
Model:	Talkabout T482

Har du brug for hjælp?

Hvis du har brug for hjælp til Motorola Talkabout T482 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Radio Motorola Manualer

Motorola Talkabout T383 Manual

10 September 2024

Motorola APX 8000HXE Manual

31 August 2024

Motorola MOTOTRBO R7 Manual

30 August 2024

Motorola MOTOTRBO Ion Manual

30 August 2024

Motorola MOTOTRBO CP100d Manual

1 August 2024

Motorola Talkabout T482 Manual

1 August 2024

Motorola Talkabout T380 Manual

28 Juli 2024

Motorola APX 8000 Manual

27 Juli 2024

Motorola MOTOTRBO R2 Manual

26 Juli 2024

Motorola Talkabout T210 Manual

21 Juli 2024

Radio Manualer

Nyeste Radio Manualer

Midland GXT5000 Manual

15 September 2024

Blaupunkt HR7BR Manual

15 September 2024

Albrecht ARC125 Manual

15 September 2024

Muse M-091 R Manual

15 September 2024

Denver DAB-46 Manual

14 September 2024

Blaupunkt BCR-9DABi Manual

14 September 2024

Sangean WR-12 BT Manual

14 September 2024

Sangean DPR-35 Manual

13 September 2024

AudioSonic CD-1585 Manual

13 September 2024

Midland 75-822 Manual

13 September 2024