Nitecore EC11 Manual
Nitecore
Lommelygter
EC11
Læs nedenfor 📖 manual på dansk for Nitecore EC11 (1 sider) i kategorien Lommelygter. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/1
EC11
Features
· Utilizes CREE XM-L2 (U2) LED
· Maximum output of 900 lumens
· Integrated “Precision Digital Optics Technology” provides extreme reflector performance
· Boasts a peak beam intensity of 9000 cd and a throw distance of up to 190 meters
· Dual-switch design ensures unprecedented ease of use
· Secondary red LED provides constant / flashing illumination
· Indicates battery voltage with a red flashing LED (accurate to 0.1V)
· High efficiency constant current circuit enables maximum runtime of up to 20 hours
· Direct access to ultra-low and turbo output
· Reverse polarity protection prevents damage from an incorrectly inserted battery
· Detachable anti-rolling clip
· Toughened ultra-clear mineral glass with anti-reflective coating
· Constructed from aero grade aluminum alloy
· HAIII military grade hard-anodized
· Waterproof in accordance with IPX-8 (2 meters submersible)
· Impact resistant to 1.5 meters
· Tail stand capability
Dimensions
Length: 2.95” (75mm)
Head diameter: 1” (25.4mm)
Tail diameter: 1” (25.4mm)
Weight: 1.60oz (45.3 gram) (without battery)
Instant Ultra-low Output
With the light switched off, press and hold the ON/OFF button for more than one second to
access ultra-low mode (1 lumen).
Instant Turbo Output
With the light switched off, press and hold the MODE button for more than one second to access
turbo mode (900 lumens).
NOTE: When in turbo mode, the EC11 will adjust output luminance automatically within 3 minutes
of use to prevent overheating and extend battery longevity.
Red Light / Signal Light Mode
With the light switched off, press the MODE button to enter red light mode. In this mode, the
secondary red LED will illuminate steadily.
When in red light mode, press and hold the MODE button for more than one second to enter
signal light mode. In this mode, the secondary red LED will flash to serve as a signal light.
Simply press any button to exit the red light /signal light mode.
Special modes (Strobe/Location/SOS)
With the light switched on, press and hold the MODE button for more than one second to enter
Strobe mode. When in strobe mode, press and hold the MODE button for more than one second
again to cycle through Location Beacon, SOS and Strobe modes. To exit, simple press the MODE
button to resume the last used brightness level, or press the ON/OFF button to switch the
light off.
Strobe Ready
With the light switched off, press the MODE button twice in quick succession to enter Strobe
mode. To exit, simply press any button.
Lockout / Unlock
With the light switched on, press and hold the ON/OFF button and the MODE button
simultaneously for over one second to switch the light off and enter lockout mode. In lockout mode,
the EC11 conserves battery power for over 170 days; the two buttons on EC11 will not work, thus
preventing accidental activation of the light. To exit lockout mode, simply press and hold the
ON/OFF button and the MODE button simultaneously for over one second again.
NOTE:
1. When entering lockout mode, the secondary red LED will continuously flash to indicate battery
voltage. Please refer to the “Power Tips” section for more details.
2. When the EC11 is kept in a backpack or left unused for extended periods, Nitecore recommends
the tailcap is loosened or battery is removed to cut off the power entirely, thus preventing
accidental activation of the flashlight or battery leakage.
Power Tips
After battery installation or lockout mode activation, the secondary red LED will flash to indicate
battery voltage (accurate to 0.1V). For example, when battery voltage is at 4.2V, the red LED will
flash 4 times, followed by a one second pause and another 2 flashes. Different voltages represent
the corresponding remaining battery power levels:
Output & Runtime
NOTICE:
The stated data has been measured in accordance with the international flashlight testing
standards ANSI/NEMA FL1, using 1 x high quality IMR18350 battery (3.7V 700mAh) or 1 x
Nitecore CR123 battery (3V 1700mAh) under laboratory conditions. The data may vary during
real-world use due to different battery usage or environmental conditions
Operating Instructions
Battery installation
Insert one (R)CR123 battery or one IMR18350 battery as illustrated
NOTE: After loading the battery, the secondary red LED will flash to indicate
battery voltage. Please refer to the “Power Tips” section of this manual for
details.
WARNING:
1. Ensure the battery is inserted with the positive (+) end pointing towards the
head. The EC11 will not be operational with an incorrectly inserted battery.
2. The included battery magazine securely holds the (R)CR123 battery in
place, thus stopping battery movement in the compartment.
3. Please stop using and remove a depleted IMR18350 battery to avoid
potential battery damage.
Accessories
Quality holster, (R)CR123 battery magazine,
clip, lanyard, spare o ring
Battery Options
4.2V3.5V 3.7V 3.9V
Low Power Full Power
3.2V2.4V 2.8V 3.0V
Low Power Full Power
IMR18350:
CR123:
®
The All-Round Flashlight Expert
TYPE Nominal voltage Compatible
Primary Lithium battery CR123 3V Y (Recommended)
IMR18350 Rechargeable Li-ion battery IMR18350 3.7V Y
Rechargeable Li-ion battery RCR123 3.7V Y
Thanks for purchasing NITECORE!
User Manual
On / Off Operation
To switch ON: Press the ON/OFF button once.
To switch OFF: Press the ON/OFF button once again to switch the light off and enter standby mode
Standby Mode
With the light switched on, press and hold the ON/OFF button for more than one second to switch the
light off and activate the secondary red LED to flash once every three seconds, thus helping the user
locate the EC11 in dark conditions. When using a CR123 battery, the EC11 will operate for up to 6
consecutive days with the red LED on, or remain on standby for more than 170 days with the red LED off.
Brightness Levels
With the EC11 switched on, press the MODE button repeatedly to cycle through the following
brightness levels: ultra-low, low, medium, high and turbo. Once a mode is selected it will be saved
and resumed when the EC11 is reactivated.
Changing / Charging Battery
Battery should be replaced or recharged when output appears to be dim or the flashlight becomes
unresponsive.
Maintenance
Every 6 months, threads should be wiped with a clean cloth followed by a thin coating of
silicon-based lubricant.
Warranty Service
All NITECORE® products are warranted for quality. Any DOA/defective product can be exchanged
for a replacement through a local distributor/dealer within 15 days of purchase. After 15 days, all
defective/malfunctioning NITECORE® products will be repaired free of charge for a period of 60
months (5 years) from the date of purchase. Beyond 60 months (5 years), a limited warranty
applies, covering the cost of labor and maintenance, but not the cost of accessories or
replacement parts.
The warranty is nullified in all of the following situations:
1. The product(s) is/are broken down, reconstructed and/or modified by unauthorized parties.
2. The product(s) is/are damaged through improper use.
3. The product(s) is/are damaged by leakage of batteries.
For the latest information on NITECORE® products and services, please contact your national
NITECORE® distributor or send an email to service@nitecore.com
The Nitecore official website shall prevail in case of any product data changes.
SYSMAX Industry Co., Ltd.
TEL: +86-20-83862000
FAX: +86-20-83882723
E-mail: info@nitecore.com
Web: www.nitecore.com
Address： Rm1401-03, Glorious Tower, 850 East Dongfeng Road,
Guangzhou, China 510600
Please follow our facebook for
more info: NITECORE Flashlights
TURBO HIGH MID
LUMENS
300
LUMENS
900
LUMENS
160
30
min
1
h
30
min
45
min
LUMENS
230
LUMENS
430
LUMENS
100
45
min
1
h
30
min
3
h
15
min
LOW
LUMENS
70
2
h
30
min
LUMENS
40
8
h
30
min
LOWER
LUMEN
1
12
h
LUMEN
1
20
h
190m (Beam Distance)
9000cd (Peak Beam Intensity)
IPX-8, 2m
(Waterproof AND Submersible)
1.5m (Impact Resistant)
CR123 IMR18350
IMR 18350
Produkt Specifikationer
| Mærke: | Nitecore |
| Kategori: | Lommelygter |
| Model: | EC11 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Nitecore EC11 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Lommelygter Nitecore Manualer
14 Oktober 2024
13 Oktober 2024
12 Oktober 2024
12 Oktober 2024
11 Oktober 2024
11 Oktober 2024
14 Juli 2024
13 Juli 2024
13 Juli 2024
12 Juli 2024
Lommelygter Manualer
- Lommelygter Panasonic
- Lommelygter AEG
- Lommelygter Makita
- Lommelygter Milwaukee
- Lommelygter Black And Decker
- Lommelygter Crivit
- Lommelygter FERM
- Lommelygter Silva
- Lommelygter Ansmann
- Lommelygter Hi-Tec
- Lommelygter Led Lenser
- Lommelygter Petzl
- Lommelygter Barska
- Lommelygter Anslut
- Lommelygter Olight
- Lommelygter Maglite
- Lommelygter Fenix
- Lommelygter Klarus
Nyeste Lommelygter Manualer
13 Oktober 2024
12 Oktober 2024
12 Oktober 2024
11 Oktober 2024
11 Oktober 2024
11 Oktober 2024
11 Oktober 2024
10 Oktober 2024
8 Oktober 2024
7 Oktober 2024