Nuc Electronics NFS-9000U - Combo 3 Food Processor Manual

Nuc Electronics Foodprocessor NFS-9000U - Combo 3 Food Processor

Læs nedenfor 📖 manual på dansk for Nuc Electronics NFS-9000U - Combo 3 Food Processor (1 sider) i kategorien Foodprocessor. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

Instruction Manual

updated in MAY, 2006

FOOD PROCESSOR InstruCtIon Manual

Important Safeguards

SAVE THESE INSTRUCTION

BOOKLET ADVANTAGES

OF FOOD PROCESSOR

For Juicer

ㆍRead all instructions carefully before using.

ㆍBlades are sharp. Please handle them with care.

ㆍDo not use the product outdoors.

ㆍVerify that the voltage in your home corresponds to that of your appliance.

ㆍDo not operate any appliance with damaged cord or plug, or after appliance has been dropped or

damaged in any way. Return the appliance to the nearest authorized service facility for examination,

repair or electrical or mechanical adjustment.

ㆍTo protect against the risk of electrical shock, do not put cord, plug, base, or motor in water or other liquid.

ㆍAlways unplug from outlet when not in use, before removing food and before cleaning.

To unplug, grasp plug and pull from electrical outlet. Never pull cord.

ㆍDo not let cord hang over the edge of table or counter, or touch hot surface.

ㆍKeep hands, spatulas and other utensils away from moving blades or discs while processing food,

to prevent the possibility of severe personal injury or damage to food processor.

A plastic scraper can be used, but only when the food processor motor is stopped.

ㆍAvoid contact with moving parts. Never push food down by hand when slicing or shredding.

Always use pusher, or injury can be occurred.

ㆍMake sure motor has completely stopped before removing cover

ㆍNever store any blade or disc on motor shaft, to reduce the risk of injury.

Store blades and discs out of reach of children.

ㆍMake sure that the cover and feed tube are securely locked in a place before operating food processor.

ㆍThe unauthorized use or not sold by NUC may cause fire, electrical shock or damage to

your food processor.

ㆍImmediately unplug and contact authorized service facility, during operation, when you hear

unusual sound or when you smell unusual or when you see smoke

ㆍPower full motor enables chops, minces, blends, mixes and emulsifies in a matter

of seconds, even very hard substances and fibrous vegetables.

ㆍMultipurpose functions such as juicing, mincing, chopping, mixing, doughing,

slicing, shredding and etc.

ㆍTwo ways safety system: Your food processor will not operate unless the work

bowl and work bowl cover are properly locked on the base.

ㆍDetachable system for multifunction and easy cleaning: The work bowl and

blades can be detachable, so you can choose accessories for your purpose and

can be cleaned with easy.

ㆍTwice wide mouth of feed tube than others, perfect for slicing whole fruits and

vegetables.

ㆍGood and state-of-art design

combo 3

For

Juicer

For

Crushing/

Chopping/

Mixer

For

Slice/

Shred

FOOD PROCESSOR FEATURES

OPERATING GUIDE SWITCH PANNEL JUICER ASSEMBLY INSTRUCTION

For Crushing/Chopping/Mixer

For Slice/Shred

FOOD PROCESSOR combo 3

04/05

FOOD PROCESSOR InstruCtIon Manual

combo 3

06/07

1. JUICING FUNCTION

ㆍPush “Low” button

ㆍNeed Juicing Screen

ㆍMake natural juice with fruits, carrot, cucumber and edible roots.

ㆍMake potato pan fried cake or croquette or tofu with Juicing Screen.

2. CRUSH FUNCTION

ㆍPush “High” button.

ㆍNeed Crush Blade.

ㆍMake flour with dried beans, parched adlay.

3. CHOPPING FUNCTION

ㆍPush “Off” button.

ㆍNeed Chopping Blade.

ㆍGarlic, onion, unripe hop pepper, dried pepper, fish, and meat can be chopped.

4. MIXING FUNCTION

ㆍPush “High” button.

ㆍNeed Crush Blade.

ㆍMake fibroid Juice with crushed fibroid fruits, vegetables along with beverage.

5. SHAVED ICE FUNCTION

ㆍPush “Off” button

ㆍNeed Chopping Blade

ㆍShave Ice

6. SHRED & SLICE FUNCTION

ㆍPush “Low” button

ㆍNeed Disc for Shred/Slice

ㆍShred/Slice with vegetables, carrots, radish, cucumbers, sweet potato, lotus root and onion.

1.Put Juicing Bowl on Base Body. Insert

Round Juicing Screen firmly as drawing.

2.Put Juicer Cover on Juicing Bowl and

lock firmly fixing clamps with both hands

till you hear click as drawing.

3.Put Waste Container to the Juicer Cover

outlet direction as drawing.

4.Put button first 3-5 seconds,

and then put materials.

REMARK: DISASSEMBLY CAN BE DONE CONVERSELY.

FOOD PROCESSOR InstruCtIon Manual

combo 3

08/09

CRUSHING/CHOPPING

ASSEMBLY INSTRUCTION

HOW TO USE BLADE OPENER

1.Insert desired blade into spindle axle of

Work Bowl as drawing.

FOOD PROCESSOR InstruCtIon Manual

combo 3

10/11

HOW TO USE DISC FOR SHRED/SLICE

WARRANTY

NOTICE BEFORE USE SLICE

HOW TO MAINTAIN

2.Put materials in Work Bowl first and

assemble Work Bowl Cover as drawing.

3.Put Work Bowl on Base Body, position

the side lockers of the Work Bowl to the

fixing clamps of Base Body. And lock

fixing clamps with both hands till you

hear click as drawing.

When the blade cannot be opened with you finger,

please use the blade opener as drawing.

4.Push button for working.

REMARK: DISASSEMBLY CAN BE DONE CONVERSELY.

Blade Opener

SHRED & SLICE ASSEMBLY

1.Put Slice Body on Base

Body and then position Slice

Bowl on the Slice Body to

the direction of the oval

sliced base Body as drawing.

2.Put Disc for Outlet on Slice

Body and then assemble

desired Disc for Shred/Slice

as drawing.

3.Put Slice Cover the direction

of the oval sliced base Body

as drawing.

4.Put Waster Container or other

Container to the direction of

Outlet as drawing

5.Push “Low” button, after 2-3

seconds, put materials with

Small/Large Feed Tube Pusher.

REMARK: DISASSEMBLY CAN BE DONE CONVERSELY.

You can use disc front or rear side according to desired function as table shown.

Slice Low

Shred Low

Function Material Shape Disc Direction Button Function

Slice for all kinds of vegetables,

radish, carrot, cucumber, sweet

potatoes, lotus root and onions.

Shred for radish, carrot, cucum-

ber, sweet potatoes, and onions.

1.Wash with warm water and neutral detergent

and wipe with a dishtowel. Do not use luffa.

Clean Round Juicing Screen with supplied

brush.(Be careful when you clean knives)

2.Be careful not to be wet Main Body and Slice

Bowl and wipe with dried dishtowel.

Water in motor can be caused mal-function or

electric shock.

3. When you wash the product, do not use

chemical product. If you use chemical

product, the color of product can be changed.

4. Do not put product in the direct ray of light or

humid area.

1.Be careful of knives for they are very sharp.

2.When you stop and want to open slice cover, be sure of complete stop of knife.

3.Do not push Small/Large Feed Tube Pusher too strongly to protect knife.

4.When you hear noise or vibration, stop machine and take out the remnants from knife and start again.

5.Please use Small Feed Tube Pusher only in Large Feed Tube Pusher.

GENERAL NOTICE BEFORE USE

ELECTRICAL SPECIFICATION

1.Make sure to use appropriate voltage.

2.Make sure of assembling status for main body, bowl, bowl cover and clamp.

3.For safety purpose, do not put the product near by children.

ITEM

VOLTAGE/HERZ

STANDARD WATTAGE

MODEL NUMBER

CONTINUOUS MAXIMUM USE

JUICER/MIXER/SLICER (COMBO 3)

120V, 60Hz

350W

NFS-9000U

3 MINUTES

#679 CHIMSAN-3DONG, BUKGU, DAEGU-CITY, R.O.KOREA

TEL. 82-(0)53-665-5066 FAX. 82-(0)53-353-7018

Homepage. http://www.nuc.co.kr

NUC Electronics Co., Ltd. and its authorized dealers guarantee this product against defects for 12

months from date of purchase for all parts and 5 years for motors and will replace them as

follows:

1. NUC and its authorized dealers shall replace any and all parts (12 months from the date of

purchase) at no charge if this product is defective due to faulty materials or manufacturing.

After the warranty period you must pay for all charges including parts, labor, shipping and

handling.

2. To receive service from authorized dealers, you must present the proof of purchase, showing

name and address of supplier, together with the date of purchase. You must also supply, in

writing, your name and full address including postcode, together with a contact telephone

number, detailing any fault in full. The Proof of Purchase in the form of a bill of sale or

receipted invoice, which is evidence that the unit is within the warranty period, must be

presented to receive warranty service.

3. When returning the product to authorized dealer, the item should be packed carefully in a

carton box with protective materials inside to avoid damage during transportation.

4. This warranty does not cover wear and tear, cosmetic damage or damage due to acts of nature,

accident, misuse, abuse, negligence, commercial use, or modification of, or to any parts of the

product, including the accessories. This warranty does not cover damage due to improper

operation or maintenance, use of improper voltage supply or attempted repair by anyone other

than a facility authorized by NUC to service the product. This warranty is valid all over the

world.

5. This warranty is in addition to the consumer’s statutory rights and does not diminish the above

rights in any way.

REFAIR/REPLACEMENT AS PROVIDED UNDER THIS WARRANTY

IS AVAILABLE EXCLUSIVELY TO THE CONSUMER. NUC SHALL

NOT BE LAIBLE FOR ANY INCIDENTAL OR CONSEQUENTAL DAM-

AGES FOR BREACH OF ANY EXPRESS OR IMPRIED WARRANTY

ON THIS PRODUCT. EXCEPT TO THE EXTENT PROVIDED BY

APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABIL-

ITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PROD-

UCT IS LIMITED IN DURATION TO THIS WARRANTY.

IMPORTANT SAFEGUARDS

FOOD PROCESSOR FEATURES

OPERATING GUIDE SWITCH PANNEL

JUICER ASSEMBLY INSTRUCTION

CRUSHING/CHOPPING ASSEMBLY INSTRUCTION

SHRED & SLICE ASSEMBLY

HOW TO USE DISC FOR SHRED/SLICE

ELECTRICAL SPECIFICATION

WARRANTY

Table of Contents

NUC ELECTRONICS CO., LTD.

Feed Tube Pusher

Round Juicing Screen

Juicer Cover

Cleaning Blush

Stainless Juicing Bowl

Waste Container

Base (common use)

Fixing Clamp

Base (common use)

Fixing Clamp

Base (common use)

Fixing Clamp

Air Cover

Work Bowl Cover

Work Bowl

Blade for Chop/Dough

Blade for Crush

Blade Opener

Small Feed Tube Pusher

Large Feed Tube Pusher

Slice Cover

Disc for slice

Disc for shred

Disc for Outlet

Slice Bowl

Slice Body

Produkt Specifikationer

Mærke:	Nuc Electronics
Kategori:	Foodprocessor
Model:	NFS-9000U - Combo 3 Food Processor

Har du brug for hjælp?

Hvis du har brug for hjælp til Nuc Electronics NFS-9000U - Combo 3 Food Processor stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Foodprocessor Nuc Electronics Manualer

Nuc Electronics NFS-9000U - Combo 3 Food Processor Manual

26 August 2024

Nuc Electronics NUC-4300U - Yogurt maker Manual

26 August 2024

Nuc Electronics Red Ginseng Maker Manual

26 August 2024

Nuc Electronics Herb Brewing Maker Manual

26 August 2024

Nuc Electronics NJM-9000U Combo Manual

26 August 2024

Nuc Electronics Power Blender 3000 Manual

26 August 2024

Foodprocessor Manualer

Nyeste Foodprocessor Manualer

KitchenAid Artisan Mixer Manual

15 Oktober 2024

Swan SP33010BLN Manual

8 Oktober 2024

Kenwood KMM063 Manual

8 Oktober 2024

Laica PM2000 Manual

5 Oktober 2024

Kenwood MultiPro Classic FDM780 Manual

4 Oktober 2024

Sencor STM 3624RD Manual

3 Oktober 2024

Kenwood FDP613WH Manual

3 Oktober 2024

Comfee MJ-LZ30W223 Manual

2 Oktober 2024

Princess Royal 2-in-1 Mini Chopper 212081 Manual

2 Oktober 2024

Turmix varioTronic Professional Manual

1 Oktober 2024