Omnitron Systems FlexPoint Manual

Omnitron Systems Medieafspiller FlexPoint

Læs nedenfor 📖 manual på dansk for Omnitron Systems FlexPoint (1 sider) i kategorien Medieafspiller. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

Warning

The operating description in this Instruction Manual is

for use by qualied personnel only. To avoid electrical

shock, do not perform any servicing of this unit other

than that contained in the operating instructions, unless

you are qualied and certied to do so by Omnitron

Systems Technology, Inc.

Caution

All user-required operations can be performed without

opening the unit. Never attempt to open or remove the

cover or tamper with the unit.

Warranty

This product is warranted to the original purchaser

against defects in material and workmanship for a period

of TWO YEARS from the date of shipment. A LIFETIME

warranty may be obtained by the original purchaser

by REGISTERING this product with Omnitron within

90 days from the date of shipment. TO REGISTER,

COMPLETE AND MAIL OR FAX THE REGISTRATION

PORTION OF THIS INSTRUCTION MANUAL TO THE

INDICATED ADDRESS. Or you may register your

product on the internet at http://www.omnitron-systems.

com. During the warranty period, Omnitron will, at its

option, repair or replace a product which is proven to

be defective.

For warranty service, the product must be sent to

an Omnitron designated facility, at Buyer’s expense.

Omnitron will pay the shipping charge to return the

product to Buyer’s designated US address using

Omnitron’s standard shipping method.

Limitation of Warranty

The foregoing warranty shall not apply to defects

resulting from improper or inadequate use and/or

maintenance of the equipment by Buyer, Buyer-supplied

equipment, Buyer-supplied interfacing, unauthorized

modications or tampering with equipment (including

removal of equipment cover by personnel not specically

authorized and certied by Omnitron), or misuse, or

operating outside the environmental specication of the

product (including but not limited to voltage, ambient

temperature, radiation, unusual dust, etc.), or improper

site preparation or maintenance.

No other warranty is expressed or implied. Omnitron

specifically disclaims the implied warranties of

merchantability and tness for any particular purpose.

Exclusive Remedies

The remedies provided herein are the Buyer’s sole and

exclusive remedies. Omnitron shall not be liable for any

direct, indirect, special, incidental, or consequential

damages, whether based on contract, tort, or any

legal theory.

User Warranty Registration

Please register on-line @ http://www.omnitron-systems.com or complete both sides

and mail or fax this registration form to:

FlexPoint Type: 10/100, Fiber Type:_______Connector: _______

Model: _________________________________________________

Serial Number: ______________ Purchase Date: ______________

Purchased From: _________________________________________

Address: ______________________________________________

City: ___________________ State: _______ Zip Code: ________

Country: _______________________________________________

Comments and Suggestions: _______________________________

______________________________________________________

Please complete both sides of this form

LED Indicators:

LED Color Description

Power: Yellow Power applied

UTP Auto: Green Auto-Negotiation enabled

UTP FDx: Green Full-Duplex detected

UTP Link: Green Link / Data received

UTP 10: Yellow 10 Mbps link detected

UTP 100: Green 100 Mbps link detected

Fiber FDx: Green Full-Duplex selected

F/O Link: Green Link / Data received

Switches:

Description Function

1- UTP Crossover: Straight / Crossed

2- UTP Auto: Auto-Negotiation / Manual

3- UTP 10/100: 10 Mbps / 100 Mbps

4- UTP Duplex: Full-Duplex / Half-Duplex

5- Fiber Duplex: Full-Duplex / Half-Duplex

Technical Support:

For help with this product, contact our Tech. Support:

Phone: (949) 250-6510

Fax: (949) 250-6514

Address: Omnitron Systems Technology, Inc.

38 Tesla

Irvine, CA 92618 USA

E-mail: support@omnitron-systems.com

URL: http://www.omnitron-systems.com

Form: 040-04340-001E 10/13

2. When used in a standalone conguration, this product

must be used with a Listed Direct Plug-In Power Unit

marked “Class 2” and rated at 9VDC, 1 Amp.

WARNING!

Before inserting the Power Adapter, verify that the power

on the unit is appropriate for your AC line voltage source.

3. To power the unit using a DC power source, prepare

a power cable using a two conductor insulated wire

(not supplied) with a 14 AWG gauge minimum. Cut the

power cable to the length required. Strip approximately

3/8 of an inch of insulation from the power cable wires.

Connect the power cables to the unit by fastening the

stripped ends to the DC power connector. Connect the

power wires to the DC power source. The Power LED

should indicate the presence of power.

Installation Procedure:

1. Configure the appropriate 10/100 DIP-Switch

settings.

2. Connect the RJ-45 port via a Category 5 or better

cable to a 10BASE-T or 100BASE-TX Ethernet device.

3. When using xed ber port models, connect the

appropriate multimode or single-mode ber cable to

the ber port of the installed module. It is important to

ensure that the transmit (Tx) is attached to the receive

side of the device at the other end and the receive (Rx)

is attached to the transmit side.

4. When using a 10/100 SFP model, insert the SFP

Fiber transceiver into the Port 1 SFP receptacle on the

10/100.

NOTE: The release latch of the SFP Fiber transceiver

must be in the closed (up) position before insertion.

User Warranty Registration

Please register on-line @ http://www.omnitron-systems.com or complete both sides

and mail or fax this registration form to:

Omnitron Systems Technology, Inc.

38 Tesla

Irvine, CA 92618, USA

Fax: (949) 250-6514

Name: _________________________________________________

Company: ______________________________________________

Address: ______________________________________________

______________________________________________

City: ___________________ State: _______ Zip Code: ________

Country: _______________________________________________

Phone: ____________________ Fax: _______________________

E-mail: _________________________________________________

Please complete both sides of this form

FlexPoint™

10/100 User Instructions

Description:

The FlexPoint 10/100 is a modular 10BASE-T or

100BASE-TX UTP to 100BASE-FX fiber media

converter featuring a 10/100 auto-sensing RJ-45 port.

The available models are shown below:

Model Dual Fiber Type Max Distance Connector

4340 1310 nm (MM) 5 km SC

4341 1310 nm (SM) 30 km SC

4342 1310 nm (MM) 5 km ST

4343 1310 nm (SM) 30 km ST

4344 1310 nm (SM) 60 km SC

4345 1310 nm (SM) 60 km ST

4347 1550 nm (SM) 85 km SC

4349 1550 nm (SM) 120 km SC

4359 SFP - LC

Model Single Fiber Type Max Distance Connector

4357-1 Tx13/Rx15 (SM) 20 km SC

4357-2 Tx15/Rx13 (SM) 20 km SC

About this Manual:

This document supports revision “3.x” of the FlexPoint

10/100. Please refer to the serial number label on

the FlexPoint 10/100 for the revision number of your

product.

Applying Power:

1. This product should only be used with Omnitron

supplied AC power supply model numbers 9113-PS

[US] or 9115-PS [Universal].

Switch Settings:

RJ-45 Crossover Switch

When the RJ-45 port is set to auto-negotiation, the

Auto-Crossover functionality is enabled and the RJ-45

Crossover Switch is disabled. When the RJ-45 port is

set to manual operation, the RJ-45 Crossover Switch

is enabled. The switch provides a convenient way to

connect to different devices and cables types.

UTP Auto/Man Switch

Setting the switch to “Auto” (factory default) enables the

RJ-45 port to automatically determine the speed and

duplex mode of the connected device. If the connected

device cannot provide the proper signal to indicate its

mode of operation, set the switch to “Man.”

UTP 10/100 Switch

When the “Auto/Man” switch is in “Man” position, the

“UTP 10/100” switch determines the speed of the RJ-45

port. When set to “100” (factory default), the RJ-45 port

will operate at 100 Mbps. When set to “10” the RJ-45

port will operate at 10 Mbps.

UTP FDX/HDX Switch

When the “Auto/Man” switch is in “Man” position, the

“UTP FDX/HDX” switch determines the duplex mode for

the RJ-45 port. When set to “FDX” (factory default), the

RJ-45 port operates in Full-Duplex. When set to “HDX”,

the RJ-45 port operates in Half-Duplex.

Fiber FDX/HDX Switch

Setting the “Fiber FDX/HDX switch to “FDX” sets the

ber port to Full-Duplex (factory default). Setting the

“Fiber FDX/HDX switch to “HDX” sets the ber port to

Half-Duplex.

Produkt Specifikationer

Mærke:	Omnitron Systems
Kategori:	Medieafspiller
Model:	FlexPoint

Har du brug for hjælp?

Hvis du har brug for hjælp til Omnitron Systems FlexPoint stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Medieafspiller Omnitron Systems Manualer

Omnitron Systems iConverter Gx AN Manual

31 August 2024

Omnitron Systems FlexPoint GX/T Manual

31 August 2024

Omnitron Systems FlexPoint Manual

27 August 2024

Medieafspiller Manualer

Nyeste Medieafspiller Manualer

Kenwood DMX823WXS Manual

16 December 2024

Philips DVP3250K Manual

12 December 2024

Philips PET726B Manual

12 December 2024

Philips PET724B Manual

12 December 2024

Philips DVP5106K Manual

12 December 2024

Philips DVP3008 Manual

12 December 2024

Philips DVP3028 Manual

12 December 2024

Philips DVP3747 Manual

12 December 2024

Philips DVP3030A Manual

12 December 2024

Pure Acoustics Jolt X225 Manual

8 December 2024