Onkyo SKS-HT728 Manual

Onkyo Hjemmebiograf sæt SKS-HT728

Læs nedenfor 📖 manual på dansk for Onkyo SKS-HT728 (1 sider) i kategorien Hjemmebiograf sæt. Denne guide var nyttig for 19 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

Enjoying Home Theater

The Home Theater means that you can enjoy surround sound with a real sense of movement in your own home — just like being in

a movie theater or concert hall.

Connecting the Speakers

Corner

position

1/3 of wall

position

Center speaker (SKC-770)

Position it close to your TV (preferably

on top) facing forward at about ear

level, or at the same height as the

front left and right speakers.

Front left and right speakers (SKF-770)

They should be positioned facing the listener at about ear level, and

equally spaced from the TV. Angle them inward slightly so as to

create a triangle, with the listener at the apex. Surround left and right speakers (SKR-770)

Position them at the sides of the listener, or

slightly behind, about 2 to 3 feet (60 to 100 cm)

above ear level. Ideally they should be equally

spaced from the listener.

Subwoofer (SKW-770)

The subwoofer handles the bass sounds of the LFE (Low-Frequency

Effects) channel. The volume and quality of the bass output from your

subwoofer will depend on its position, the shape of your listening room,

and your listening position. In general, a good bass sound can be obtained

by installing the subwoofer in a front corner, or at one-third the way along

the front wall, as shown.

Red White

Blue

Green

Front right speaker

Center speaker

Gray

Front left speaker

Surround right speaker Surround left speaker

Powered

subwoofer

Speaker Connection Precautions

Read the following before connecting your

speakers:

• Turn off your receiver before making any

connections.

• Pay close attention to speaker

wiring polarity. Connect

positive (+) terminals to only

positive (+) terminals, and

negative (–) terminals to only

negative (–) terminals. If the speakers are

wired incorrectly, the sound will be out of

phase and will sound unnatural.

• Be careful not to short the positive and

negative wires. Doing so may damage

your amp.

Specifications

■Powered Subwoofer (SKW-770)

■Front Speakers (SKF-770)

■Center Speaker (SKC-770)

■Surround Speakers (SKR-770)

Specifications and appearance are subject to change without

prior notice.

Type: Bass-reflex

Input sensitivity/impedance: 140 mV / 20 kΩ

Maximum output power: 290 W (Dynamic Power)

Frequency response: 25 Hz to 150 Hz

Cabinet capacity: 37 L (1.3 cubic feet)

Dimensions (W × × H D): 275 × 507 × 411 mm

(10-13/16" × × 19-15/16" 16-3/16")

(incl. projection)

Weight: 11.6 kg (25.6 lbs.)

Drivers unit: 25 cm (10") Cone Woofer × 1

Power supply: AC 220 V – 240V, 50/60 Hz

Power consumption: 137 W

Other: Auto Standby function

Type: 2 Way Bass-reflex

Impedance: 6 Ω

Maximum input power: 130 W

Sensitivity: 79.5 dB/W/m

Frequency response: 55 Hz to 50 kHz

Crossover frequency: 4 kHz

Cabinet capacity: 7.3 L (0.26 cubic feet)

Assembly dimensions (with supplied speaker base) (W × × H D):

262 × 1050 × 262 mm

(10-5/16" × 41-5/16" × 10-5/16")

(incl. projection)

Weight: 5.2 kg (11.5 lbs.) (incl. speaker base)

Drivers unit: 8 cm (3-1/4") cone (Woofer) × 2

2.5 cm (1") Balanced dome (Tweeter)

Terminal: Spring type color coded

Grille: Fixed

Type: 2 Way Bass-reflex

Impedance: 6 Ω

Maximum input power: 130 W

Sensitivity: 79 dB/W/m

Frequency response: 60 Hz to 50 kHz

Crossover frequency: 4 kHz

Cabinet capacity: 2.8 L (0.10 cubic feet)

Dimensions (W × H × D): 430 × 115 × 121 mm

(16-15/16" × 4-1/2" × 4-3/4")

(incl. grille and projection)

Weight: 2.2 kg (4.9 lbs.)

Drivers unit: 8 cm (3-1/4") Cone (Woofer) × 2

2.5 cm (1") Balanced dome (Tweeter)

Terminal: Spring type color coded

Keyhole slot: 2

Grille: Fixed

Type: Full-range closed box

Impedance: 6 Ω

Maximum input power: 130 W

Sensitivity: 81 dB/W/m

Frequency response: 80 Hz to 20 kHz

Cabinet capacity: 1.0 L (0.036 cubic feet)

Dimensions (W × H × D): 115 × 230 × 96 mm

(4-1/2" × 9-1/16" × 3-3/4")

(incl. grille and projection)

Weight: 1.0 kg (2.2 lbs.)

Drivers unit: 8 cm (3-1/4") Cone

Terminal: Spring type color coded

Keyhole slot: 1

Grille: Fixed

Attaching the Speaker Bases

Before you connect the speakers, attach the supplied

speaker base to each SKF-770.

1. Turn the speaker

upside down with the

protection cover

attached.

2. Align the speaker

base while the arrow

mark is headed in

the same direction as

the speaker’s face. Be

careful not to tip over

the speaker.

3. Align the screw holes

on the speaker base

with those on the

bottom of each

speaker, and affix the speaker base using the

supplied screws. Recommended torque is 10 kgf·cm

(9 lbf·in). Be careful not to tip over the speaker.

4. Turn the speaker right side up.

5. Remove the protection cover.

SAFETY PRECAUTIONS:

• Attach the speaker bases in a manner that will not

allow the speakers to tip over.

• Be sure to tighten the screws when you attach the

speaker bases.

• Attach the speaker bases on a flat, level, and stable

floor.

• After you attach the speaker bases, make sure that the

speakers stand upright and are stable.

Front speaker (SKF-770)

Front speakers

Speaker cables 11 ft. (3.5 m)

2 speaker bases and 8 screws

(Red)(White)

Speaker terminals

Caution:

The front grilles are not designed to be

removed so do not attempt to remove them

forcibly, as this will damage them.

Screws

Speaker base

Bottom of

SKF-770

Arrow mark

Protection cover

Wall Mounting

To mount the center speaker horizontally, use the two keyhole slots

shown to hang each speaker on two screws that are securely screwed

into the wall.

Using the Cork Stoppers for a More Stable Platform

We recommend using the supplied cork stoppers to achieve the best

possible sound from your speakers. The cork stoppers prevent the

speakers from moving, providing a more stable platform. Use

stoppers for the center speaker.

Center speaker (SKC-770)

Center speaker

Speaker cable 10 ft.

(3.0 m)

4 cork stoppers

(Green)

Speaker terminalsKeyhole slots

Caution:

The front grilles are not designed to be removed so do not attempt

to remove them forcibly, as this will damage them.

Keyhole slots for wall mounting

7-7/8" (200 mm)

Caution:

A mounting screw’s ability to support a speaker

depends on how well it’s anchored to the wall. If

you have hollow walls, screw each mounting

screw into a stud. If there are no studs, or the

walls are solid, use suitable wall anchors. Use

screws with a head diameter of 5/16" (8 mm) or

less and a shank diameter of 5/32" (4 mm) or

less. With hollow walls, use a cable/pipe

detector to check for any power cables or water

pipes before making any holes. Leave a gap of

between 7/32" (5 mm) and 3/8" (10 mm) between the wall and the

base of the screw head, as shown. (We recommend that you

consult a home installation professional.)

Wall

7/32" to 3/8"

(5 to 10mm)

Cork stoppers

Bottom of SKC-770

Wall Mounting

To mount the surround speakers

vertically, use the keyhole slot shown to

hang each speaker on a screw that’s

securely screwed into the wall.

Surround speaker

(SKR-770)

Surround speakers

Speaker cables 26 ft. (8.0 m)

(Blue) (Gray)

Speaker

terminals

Keyhole slot

Caution:

The front grilles are not designed to be

removed so do not attempt to remove

them forcibly, as this will damage them.

Keyhole slot for

wall mounting

Caution:

A mounting screw’s

ability to support a

speaker depends on

how well it’s

anchored to the wall.

If you have hollow

walls, screw each

mounting screw into

a stud. If there are no

studs, or the walls are solid, use

suitable wall anchors. Use screws with

a head diameter of 5/16" (8 mm) or less

and a shank diameter of 5/32" (4 mm) or

less. With hollow walls, use a cable/pipe

detector to check for any power cables

or water pipes before making any holes.

Leave a gap of between 7/32" (5 mm)

and 3/8" (10 mm) between the wall and

the base of the screw head, as shown.

(We recommend that you consult a

home installation professional.)

Wall

7/32" to 3/8"

(5 to 10mm)

Setting the Subwoofer Level

To set the level of the subwoofer, use the OUTPUT LEVEL control.

Set it so that bass sounds are evenly balanced with the treble sounds

from the other speakers. Because our ears are less sensitive to very

low bass sounds, there’s a temptation to set the level of the

subwoofer too high. As a rule of thumb, set the subwoofer level to

what you think is the optimal level, and then back it off slightly.

Using the Floor Pads for Subwoofer

If the subwoofer is placed on a hard floor (wood,

vinyl, tile, etc.) and playback is very loud, the

subwoofer’s feet may damage the flooring. To

prevent this, place the supplied pads underneath

the subwoofer’s feet. The pads also provide a

stable base for the subwoofer.

Subwoofer (SKW-770)

Subwoofer

Power-plug adapter

Only supplied in certain countries. Use this

adapter if your AC outlet does not match with the

plug on the subwoofer’s power cord (adapter

varies from country to country).

RCA cable 10 ft. (3.0 m)

*How to mount the AC plug:

4 floor pads

■Front

■Rear

Note: The Auto Standby function turns the subwoofer on when the input signal

exceeds a certain level. If the Auto Standby function does not work reliably, try

slightly increasing or decreasing the subwoofer output level on your receiver.

STANDBY/ON indicator

Red: Subwoofer in standby mode

Blue: Subwoofer on

With the Auto Standby function, the SKW-770 automatically turns on

when an input signal is detected in Standby mode. When there’s no input

signal for a while, the SKW-770 automatically enters Standby mode.

SKW- 770

OFF

POWER

POWER switch

Press this switch to the ON position to turn on the

power. Press it to the OFF position to turn off the

power.

To AC outlet

OUTPUT LEVEL control

This control is used to adjust the volume of the

subwoofer.

LINE INPUT

This RCA input should be connected to the

subwoofer pre out on your AV receiver with

supplied RCA cable.

Pad

5.1ch Home Theater Speaker Package SKS-HT728

http://www.onkyo.com/

HOMEPAGE

Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8163

ONKYO U.S.A. CORPORATION

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/

ONKYO EUROPE ELECTRONICS GmbH

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/

ONKYO EUROPE UK Office

Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ

UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452

ONKYO CHINA LIMITED

Unit 1&12, 9/F, Ever Gain PlazaTower 1, 88, Container Port Road, Kwai Chung,

N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039

http://www.ch.onkyo.com/

SN 29355763

Y0906-1

* 2 9 3 5 5 7 6 3 *

Produkt Specifikationer

Mærke:	Onkyo
Kategori:	Hjemmebiograf sæt
Model:	SKS-HT728

Har du brug for hjælp?

Hvis du har brug for hjælp til Onkyo SKS-HT728 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Hjemmebiograf sæt Onkyo Manualer

Onkyo HT-S9800 Manual

13 Oktober 2024

Onkyo HT-S3700 Manual

1 September 2024

Onkyo TX-SR3100 Manual

28 August 2024

Onkyo HT-S9405 Manual

15 August 2024

Onkyo SKS-HT728 Manual

2 August 2024

Onkyo HT-S780 Manual

2 August 2024

Onkyo HT-S5305 Manual

1 August 2024

Onkyo HTP-348 Manual

31 Juli 2024

Onkyo HT-S5300 Manual

29 Juli 2024

Onkyo HT-S6300 Manual

28 Juli 2024

Hjemmebiograf sæt Manualer

Nyeste Hjemmebiograf sæt Manualer

Sony SA-PSD5 Manual

14 Oktober 2024

Panasonic SC-HT40 Manual

12 Oktober 2024

LG MAI0702 Manual

7 Oktober 2024

LG MAI0182 Manual

7 Oktober 2024

LG LH-TK3605Q Manual

7 Oktober 2024

Bose Wave Music System II Acoustic Manual

27 September 2024

Yamaha YHT-570 Manual

25 September 2024

AKAI AHC1500 Manual

23 September 2024

Klipsch Quintet 5 Manual

20 September 2024

Klipsch Quintet IV Manual

17 September 2024