Ozito PXPFS-850U Manual

Ozito Ventilator PXPFS-850U

Læs nedenfor 📖 manual på dansk for Ozito PXPFS-850U (3 sider) i kategorien Ventilator. Denne guide var nyttig for 14 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/3

WHAT’S IN THE BOX

Cordless Fan

MAINTENANCE

DESCRIPTION OF SYMBOLSTROUBLESHOOTING

SPARE PARTS

WARNING! When using mains-powered tools, basic safety precautions, including the

following, should always be followed to reduce risk of ﬁre, electric shock, personal injury

and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

Before you connect the charger to the mains supply make sure that the data on the rating plate are identical to the mains data.

This tools charger is double insulated, therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid a hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for

added protection against injury resulting from a possible electrical insulation failure within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the extension lead for signs of

damage, wear and ageing. Replace the extension lead if damaged or defective.

When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for the power input

of the tool or which is damaged or defective may result in a risk of re and electric shock.

The power supply for this products charger should be protected by a residual current device (rated at 30mA or less). A residual current

device reduces the risk of electric shock.

GENERAL POWER TOOL SAFETY WARNINGS

ELECTRICAL SAFETY

THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR

YOUR BATTERY CHARGER.

1. Before using the charger read all instructions and cautionary markings on the charger, battery

pack and the product using the battery pack.

2. This charger is not intended for any uses other than charging rechargeable batteries. Any other

use may result in risk of re, electric shock or electrocution.

3. Do not place any object on top of the charger or place the charger on a soft surface that may

result in excessive internal heat. Place the charger in a position away from any heat source.

4. To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when

disconnecting the charger.

5. Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

6. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord

could result in the risk of re, electric shock or electrocution.

7. Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in

any way. Have it checked by an electrician or power tool repairer.

8. Do not disassemble charger. Take it to an electrician or power tool repairer when service or repair

is required. Incorrect reassembly may result in a risk of electric shock, electrocution or re.

9. To reduce risk of electric shock, unplug the charger from the outlet before attempting any clean-

ing. Removing the battery pack will not reduce this risk.

10. Never attempt to connect 2 chargers together.

11. DO NOT store or use the tool and battery pack in locations where the temperature may reach or exceed

40ºC (such as inside sheds or metal buildings in summer).

12. The charger is designed to operate on standard household electrical power (240 volts). Do not

attempt to use it on any other voltage!

13. The battery pack is not fully charged out of the carton. First read the safety instructions and then

follow the charging notes and procedures.

14. The longest life and best performance can be obtained if the battery pack is charged when the

air temperature is between 18 - 24ºC. Do not charge the battery pack in an air temperature below

10ºC or above 40ºC. This is important and will prevent damage to the battery pack.

15. Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The

battery can explode in a re.

16. Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks

or cracks, immediately discontinue use and do not recharge.

17. During charging, the battery must be placed in a well ventilated area.

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and

instructions may result in electric shock, re and/or serious injury.

Save all warnings and instructions for future reference. The term “power tool” in the

warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power

tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b. Do not operate power tools in explosive atmospheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will reduce risk

of electric shock.

b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common sense when operating a power tool.

Do not use a power tool while you are tired or under the inﬂuence of drugs, alcohol or

medication. A moment of inattention while operating power tools may result in serious personal injury.

b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to

power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your

nger on the switch or energising power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and collection facilities, ensure

these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power tool for your application. The correct power

tool will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the battery pack from the power tool

before making any adjustments, changing accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with

the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts

and any other condition that may affect the power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

5. Battery tool use and care

a. Recharge only with the charger speciﬁed by the manufacturer. A charger that is suitable for one type of

battery pack may create a risk of re when used with another battery pack.

b. Use power tools only with speciﬁcally designated battery packs. Use of any other battery packs may

create a risk of injury and re.

c. When battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection from one

terminal to another. Shorting the battery terminals together may cause burns or a re.

d. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, ﬂush with water. If liquid contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or burns.

6. Service

a. Have your power tool serviced by a qualiﬁed repair person using only identical replacement

parts. This will ensure that the safety of the power tool is maintained.

• After each use, blow air through the tool housing to ensure it is free from all dust,

dirt, etc. Build up of dust, dirt particles may cause the tool to overheat and shorten

the life of the tool.

• If the housing of the fan requires cleaning, do not use solvents but a moist soft cloth

or soft brush only.

• Never let any liquid get inside the tool, never immerse any part of the tool into liquid.

• When not in use, the fan should be stored in a dry, frost free location not within the

reach of children.

WARNING! ALWAYS ENSURE THE TOOL HAS

COMPLETELY STOPPED AND THE BATTERY IS

REMOVED PRIOR TO ANY MAINTENANCE.

Battery & Charger

sold separately

LED lights do not illuminate on charger

Check the charging adaptor is securely plugged into the wall out let.

Check the battery is rmly connected to the charging cradle.

Check that the charging jack is securely connected to the charging cradle.

The fan did not shut-off after the delay time

The correct delay setting may not have been selected. Ensure the light that corresponds

to the desired time is illuminated when selecting an automatic shut-off time.

Note: Ozito Industries will not be responsible for any damage or injuries caused by

the repair of the fan by an unauthorised person or by mishandling of the fan. BATTERY AND CHARGER SAFETY WARNINGS

SPECIFICATIONS

Input: 18V

Fan Blade Diameter: 230mm

Fan Speed: 1,400 / 2,400/min

Wind Speed: 3.2 / 5.0m/sec

Tilt Adjustment: 0-90°

Weight: 1.8kg

CORDLESS

PORTABLE FAN

ORIGINAL INSTRUCTIONS

ozito-diy.co.uk

PXPFS-850U

WARRANTY

OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG 0516

All of our products undergo strict quality checks to ensure that they reach you in perfect

condition. In the unlikely event that your device develops a fault, please contact our service

department at the address shown on this guarantee card. You can also contact us by

telephone using the customer service number shown. Please note the following terms under

which guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the manufacturer

mentioned below promises to buyers of its new products in addition to their statutory

guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or manufacturing faults on

a product which you have bought from the manufacturer mentioned below are limited to

either the rectication of said defects on the product or the replacement of the product,

whichever we prefer.

Please note that our devices are not designed for use in commercial, trade or professional

applications. A guarantee contract will not be created if the device has been used by

commercial, trade or industrial business or has been exposed to similar stresses during the

guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly instructions or due to

incorrect installation, a failure to follow the operating instructions (for example connecting

it to an incorrect mains voltage or current type) or a failure to follow the maintenance and

safety instructions or by exposing the device to abnormal environmental conditions or by

lack of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example overloading the

device or the use or unapproved tools or accessories), ingress of foreign bodies into the

device (such as sand, stones or dust, transport damage), the use of force or damage caused

by external forces (for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural wear or tear or by

normal use of the device.

4. Your Product is guaranteed for a period of 60 months from the original date of purchase

and is intended for DIY (Do It Yourself) use only. Lithium Ion batteries and chargers are

covered by a 12 month warranty. Warranty excludes consumable parts. Guarantee claims

should be submitted before the end of the guarantee period within two weeks of the defect

being noticed. No guarantee claims will be accepted after the end of the guarantee period.

The original guarantee period remains applicable to the device even if repairs are carried

out or parts are replaced. In such cases, the work performed or parts tted will not result

in an extension of the guarantee period, and no new guarantee will become active for the

work performed or parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO

THE PLACE OF PURCHASE WITH YOUR REGISTER RECEIPT.

Please refer to the restrictions of this warranty concerning wearing parts, consumables and

missing parts as set out in the service information in these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

Warning Read instruction manual

mA Milliamperes

Recycle battery Do not put in the rubbish

Polarity

Do not incinerate Do not get battery wet

Thermal cut-out protection

Double insulated

Ah Amp hour

Indoor use only

Lithium Ion battery Do not use or store battery in

temperatures exceeding 50 Cº

no No load speed

VVolts Hz Hertz

ac/~ Alternating current

Direct current

dc/

Do not expose to rain.

Do not touch fan blades Do not operate near long hair

Spare parts can be ordered from the Special Orders Desk at your local

Bunnings Warehouse or Homebase store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: enquires@ozito-diy.co.uk

Produkt Specifikationer

Mærke:	Ozito
Kategori:	Ventilator
Model:	PXPFS-850U

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito PXPFS-850U stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ventilator Ozito Manualer

Ozito PXPFS-850U Manual

16 Oktober 2023

Ozito PXPFS-850 Manual

6 November 2022

Ventilator Manualer

Nyeste Ventilator Manualer

Be Cool BC121TU2201F Manual

19 November 2024

Cecotec EnergySilence 1090 RetroDesk Design Manual

18 November 2024

Emerio FN-114204.11 Manual

16 November 2024

Ardes Freddy AR5T75 Manual

16 November 2024

Midea FTS30-9BR Manual

16 November 2024

OK OSF 4332 B RC Manual

16 November 2024

Biltema 83-017 Manual

12 November 2024

Biltema 83-021 Manual

12 November 2024

Biltema 83-014 Manual

12 November 2024

Hunter Fonthill Manual

12 November 2024