PAC APH-TY02 Manual


Læs nedenfor 📖 manual på dansk for PAC APH-TY02 (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
Speaker Connection Harness for Select
Toyota and Lexus Vehicles with Factory Ampliers
Equipped with a 30-pin Dock-n-Lock Connector
APH-TY02
C
Page 1
Copyright © 2019. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev: V1
Date: 010419
APH-TY02-HAR
1
15
16
30
Yellow
Brow Whiten /
Black
Orange
Red
Pink
Brown / wYello
Blue
Green
Purple
White
Gray d/ Re
Brown
Whit Rede /
Gray
Re Blackd /
Pink / Black
Brown e / Blu
Black
Orange k / Blac
Brown
Blue / Black
Gree Blackn /
Purple k / Blac
Whit Blacke /
Gra Bluey /
Brow Blackn /
White / Blue
Gray / Black
Yellow
161
3015
Blue / Black
Gree Blackn /
Purple k/ Blac
Whit Blacke /
Gra Bluey /
Brown/Black
White e/Blu
Gray/Black
Pink / Black
Orange k/ Blac
Re Blackd /
Brown e/ Blu
Brown
Black
Yellow Yellow
Brow Whiten /
Black
Pink
Orange
Red
Brown / Yellow
Blue
Green
Purple
White
Gray / Red
Brown
Whit Rede /
Gray
Introduction and Features
The APH-TY02 simplies speaker wire connections when adding aftermarket ampliers. Aftermarket ampliers can
be easily added with no need to cut or modify a vehicle’s original wiring. Each pair of wires has been labeled with the
corresponding speaker name.
Wiring Overview
Installation Notes
1. It is always best to use a tone generator (PAC part number: TL-PTG2) to verify that the tables in this manual, and the labels
on the wires, match the wiring in your specic vehicle.
2. The 30-pin Dock-n-Lock connector from the APH-TY02 must be connected to the factory amplier when using a PAC AmpPRO
Interface.
3. Not all applicable vehicles will come equipped with a corresponding speaker for all of the wires populated in our harness. It is
important to understand which speakers are equipped in your vehicle.
4. If you are leaving any of the factory speakers connected to the factory amplier, simply connect the speaker wires (color for
color) between the male and female connectors, for the speakers that will be powered by the factory amplier. For example:
If you want the rear speakers to be powered by the factory amplier, simply connect the Green, Green / Black, Purple and
Purple / Black wires from the male connector to the Green, Green / Black, Purple and Purple / Black wires from the female
connector.
5. For vehicles that lose audio output when there is no load on the speaker outputs of the factory amplier, PAC load resistors
will be required (PAC Part Number LR335 or LR475).
1. Locate the vehicle’s factory amplier and disconnect the 30-pin Dock-n-Lock connector.
2. Connect the APH-TY02 harness to the connector that was disconnected in the previous step.
3. Connect the male connector from the APH-TY02 to the amplier.
4. Connect the longer loose wires from the APH-TY02, to your aftermarket amplier or passive crossovers, according to the
tables in this manual.
5. Insulate unused wires in the 30-pin connector that plugs into the factory amplier side of the APH-TY02.
Installation Steps
Connect to aftermarket amplier
or passive crossover
16
Gray Spea r +ke 12
1
Gray / B ck Spea r -la ke 12
17
Whi / Red Spea r +te ke 11
2
Whi / Blue Spea r -te ke 11
18
Brown Spea r +ke 10
3
Brown / B ckla S ker -pea 10
19
Gray / Red Spea r 9 +ke
4
Gray / Blue S ker 9 -pea
20
White Spea r 8 +ke
5
Whi / B ckte la S ker 8 -pea
21
Purple Spea r 7 +ke
6
Purple / B ckla S ker 7 -pea
22
Gr n Spea r 6 +ee ke
7
Gr n / B ckee la S ker 6 -pea
23
Blue Spea r 5 +ke
8
Blue / B ckla S ker 5 -pea
24
Brown / Red Spea r 4 +ke
9
Brown / Blue S ker 4 -pea
25
Pink Spea r 3 +ke
10
Pin / B ckk la S ker 3 -pea
26
Red Spea r 2 +ke
11
Red / Black S ker 2 -pea
27
Ora e Spea r 1 +ng ke
12
Ora e / B ckng la S ker 1 -pea
28
B ckla
13
B ckla
29
Brown / hite W
14
Brown
30 Ye owll
15 Ye owll
Spea r 1ke
Pass thr (Gr )ough ound
Pass thr (C st t v)ough on an 12
Spea r 6ke
Spea r 5ke
Spea r 4ke
Spea r 3ke
Spea r 2ke
Spea r 11ke
Spea r 10ke
Spea r 9ke
Spea r 8ke
Spea r 7ke
Pin Num r Wire Color Wires De riptionbe sc Label
Spea r 12ke
Pass through
Pass through
Insulate any unused wires


Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: APH-TY02

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC APH-TY02 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret PAC Manualer

PAC

PAC RP4-GM31 Manual

6 September 2024
PAC

PAC NU-CTS2 Manual

6 September 2024
PAC

PAC TR7 Manual

6 September 2024
PAC

PAC OS-5 Manual

6 September 2024
PAC

PAC NDK735MG Manual

29 August 2024
PAC

PAC RP3-GM11 Manual

29 August 2024
PAC

PAC IR-X Manual

29 August 2024
PAC

PAC AAI-GM9 Manual

29 August 2024
PAC

PAC AAI-GM12 Manual

29 August 2024
PAC

PAC CP1-FRD2 Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024