PAC AVS-21 Manual


Læs nedenfor 📖 manual på dansk for PAC AVS-21 (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
Pacic Accessory Corporation
® | Ph. 866-931-8021 | support@pac-audio.com
©2015 Pacic Accessory Corporation
www.pac-audio.com
Rev. 040815
AVS-21
Two-Way Audio/Video Switcher
P ifi A C ti
AVS-21
Two-Way Audio/Video Switcher
Pacic Accessory Corporation
® | Ph. 866-931-8021 | support@pac-audio.com
©2015 Pacic Accessory Corporation
www.pac-audio.com
Rev. 040815
P ifi A C ti
J1850
Class 2
VPW
Class 2
J1850
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0
111010000110110111001100
Arbitration
CRC
100011101111001001101100
111010000110110111001100
Class 2
Class 2
J1850
The AVS-21 is a two way A/V switcher designed for use with any of the PAC BCI interfaces. The AVS-21
can also be used as a stand alone unit for any application requiring a two way A/V switch.
Introduction & Features
Important Notes
1. The A/V output will pass the A/V 1 input at all times until the module is triggered.
2. The module can be triggered by either a positive or negative trigger, however when used with a BCI module it will always be a positive
trigger.
1. The black and red wires in the 2-pin plug are the trigger wires. If you are using the AVS-21 with a BCI interface you will connect the black wire
to ground and the red wie to the red programmable output wire on the BCI interface. If you are using the AVS-21 in any other application,
you can connect the red and black trigger wires to best suite your needs.
2. Connect the RCAs labeled “A/V1 IN” to the primary A/V source.
3. Connect the RCAs labeled “A/V2 IN” to the secondary A/V source.
4. Connect the RCAs labeled “A/V OUT” to the screen/head unit.
Installation Steps
The AVS-21 is a two way A/V switcher designed for use with any of the PAC BCI interfaces. The AVS-21
can also be used as a stand alone unit for any application requiring a two way A/V switch.
Introduction & Features
Important Notes
1. The A/V output will pass the A/V 1 input at all times until the module is triggered.
2. The module can be triggered by either a positive or negative trigger, however when used with a BCI module it will always be a positive
trigger.
1. The black and red wires in the 2-pin plug are the trigger wires. If you are using the AVS-21 with a BCI interface you will connect the black wire
to ground and the red wie to the red programmable output wire on the BCI interface. If you are using the AVS-21 in any other application,
you can connect the red and black trigger wires to best suite your needs.
2. Connect the RCAs labeled “A/V1 IN” to the primary A/V source.
3. Connect the RCAs labeled “A/V2 IN” to the secondary A/V source.
4. Connect the RCAs labeled “A/V OUT” to the screen/head unit.
Installation Steps


Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: AVS-21

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC AVS-21 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret PAC Manualer

PAC

PAC RP4-GM31 Manual

6 September 2024
PAC

PAC NU-CTS2 Manual

6 September 2024
PAC

PAC TR7 Manual

6 September 2024
PAC

PAC OS-5 Manual

6 September 2024
PAC

PAC NDK735MG Manual

29 August 2024
PAC

PAC RP3-GM11 Manual

29 August 2024
PAC

PAC IR-X Manual

29 August 2024
PAC

PAC AAI-GM9 Manual

29 August 2024
PAC

PAC AAI-GM12 Manual

29 August 2024
PAC

PAC CP1-FRD2 Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024