PAC CAM-TY12 Manual


Læs nedenfor 📖 manual på dansk for PAC CAM-TY12 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 14 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
CAM-TY12
Reverse Camera T-Harness for
Select Toyota & Scion Vehicles
www.pac-audio.com
Rev. 01182016
©2015 Pacific Accessory Corporation
Pacific Accessory Corporation® | 866-931-8021 | support@pac-audio.com
Introduction & Features
Installation:
Illustration / Schematic
The CAM-TY12 is a reverse camera T-harness that gives the ability to e i t h e r add a reverse camera input for compatible
TOYOTA and SCION OEM touchscreen radios or retain the factory camera when replacing the factory radio. Simple plug and
play installation.
1. Disassemble dash and remove the radio.
2. Disconnect the 24 pin connector from the back of the factory radio (if equipped) and install the T-harness.
3. Connect the RCA from the aftermarket camera to the female RCA located in the T-harness
3. The OEM radio, when connected to this harness, will provide a +6v power output if needed. Most aftermarket cameras
require +12v for power, if your camera requires +12v then you will need to find a reliable source of +12 volt ACC power. If
not being used please insulate the pin located at the end of the red wire.
4. To function properly the camera must have power before the vehicle is placed into reverse, so using the reverse lamp as a
power source is not recommended for proper functionality.
5. Normally a reverse trigger is long as the camera has power when the vehicle is placed into provided by the vehicle manufacturer, as
reverse, the radio should automatically switch to the reverse camera. In the event that the radio does not automatically switch
to the reverse camera a +12v reverse signal will need to be added to Pin 2 of the 28 pin connector. See Fig 1.
When adding a reverse camera to an OEM radio:
When retaining the factory reverse camera with an aftermarket radio:
1. Connect the factory 24 pin camera harness to the T-harness.
2. Connect the male side of the RCA into the aftermarket radios reverse camera input.
3. Connect the loose black wire to chassis ground.
4. Insert the pin located on the end of the red wire into the pin 12 location in the 20 pin connector of the RP4.2-TY11. This
pin is located next to the red/white programmable +12v output. See Fig. 2. If an RP4.2-TY11 is not being used along with this
harness then the red wire will need to connect to +6v. This may require an adapter to step down the voltage from +12v to +6v.
Fig. 2
Fig. 1


Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: CAM-TY12

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC CAM-TY12 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret PAC Manualer

PAC

PAC RP4-GM31 Manual

6 September 2024
PAC

PAC NU-CTS2 Manual

6 September 2024
PAC

PAC TR7 Manual

6 September 2024
PAC

PAC OS-5 Manual

6 September 2024
PAC

PAC NDK735MG Manual

29 August 2024
PAC

PAC RP3-GM11 Manual

29 August 2024
PAC

PAC IR-X Manual

29 August 2024
PAC

PAC AAI-GM9 Manual

29 August 2024
PAC

PAC AAI-GM12 Manual

29 August 2024
PAC

PAC CP1-FRD2 Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024