PAC RPA-KNOB1 Manual


Læs nedenfor 📖 manual på dansk for PAC RPA-KNOB1 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Climate control knob set for
2010 - 2015 Chevrolet Camaro
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev: 1
Date: 110918 Page 1
RPA-KNOB1
Introduction and Features
Very Important Notes
Pre-installation setup
RPA-KNOB1 is a complete set of two climate control knobs for 2010 - 2015 Chevrolet Camaro. They are designed to match
the OE climate control knob t and nish, providing a factory appearance in your late-model Camaro. They can be installed
on our PAC RadioPRO Integrated Dash Kit RPK5-GM4101, or as a replacement for the original knobs on a factory radio.
Both knobs feature back-lit buttons to match the OE appearance, and selectable center inserts to match the vehicle options,
for vehicles equipped with or not equipped with heated seats.
Note 1: The center inserts are made to install once! They are not easily removable / swappable.
Please ensure you have selected the correct inserts for your installation before snapping the inserts into the
control knobs.
In the event that the center inserts need to be removed, see the troubleshooting section on page 2.
Note 2: For vehicles with heated seats: When installing the center caps, you need to rst install the light pipes. They are
keyed so they will only t one way. Pay close attention to the shape and orientation of the light pipes to ensure
correct lighting.
Note 3: In this manual we will refer to “Left” indicating the driver side, and “Right” indicating the passenger side.
For vehicles without heated seats: Remove the center cap called “Blank Left” and snap that into the climate control knob
labeled Left. the insert is keyed, so it will only t in one orientation. Remove the center cap called “Blank Right” and snap it
into the climate control knob labeled Right.
For vehicles equipped with heated seats: Carefully open the package labeled “Heated Seat Left”. There will be a center
cap and 2 small, clear plastic, light pipes. They are keyed, so they will only t in one specic hole each.
From the front of the control knob, insert the light pipes (non-keyed side rst) into the small rectangular openings.
The left light pipe (A) has a key tab on the narrow side. Insert this light pipe with the key facing down.
The right light pipe (B) has the key tab on the wide side. Insert this light pipe with the key facing to the right.
They are installed as shown below.
(A)
(B)
Close-up of light pipes installed
key tab
key tab
Installation Steps for RPA-KNOB1 into an OE Radio
Installation on a factory radio: 1) Remove the OE knobs. 2) The original brackets and screws will be resused.
3) Install the RPA-KNOB1 knobs by reversing the steps used to remove the OE knobs.


Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: RPA-KNOB1

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC RPA-KNOB1 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret PAC Manualer

PAC

PAC RP4-GM31 Manual

6 September 2024
PAC

PAC NU-CTS2 Manual

6 September 2024
PAC

PAC TR7 Manual

6 September 2024
PAC

PAC OS-5 Manual

6 September 2024
PAC

PAC NDK735MG Manual

29 August 2024
PAC

PAC RP3-GM11 Manual

29 August 2024
PAC

PAC IR-X Manual

29 August 2024
PAC

PAC AAI-GM9 Manual

29 August 2024
PAC

PAC AAI-GM12 Manual

29 August 2024
PAC

PAC CP1-FRD2 Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024