PAC VCI-NIS2 Manual


Læs nedenfor 📖 manual på dansk for PAC VCI-NIS2 (3 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/3
Pacic Accessory Corporation - Santa Ana, CA 92705
Tech Support 866-931-8021 • www.pac-audio.com
Pacific Accessory Corporation
10-06-2009
J1850
Class 2
VPW
Class 2
J1850
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
Arbitration
EOD
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
Class 2
Class 2
J1850
VCI-NIS2
2007-2009 Nissan & Inniti Vehicles with a color LCD screen
Inaccuracies or Typographical Errors: The information in these instruction could contain technical or other mistakes, inaccuracies or
typographical errors. PAC may make changes to the materials in these instructions at any time without notice. The information in these
instructions may be out of date, and PAC makes no commitment to update such information.
Wiring the VCI-NIS2s power, ground and switch input wires:
1. Connecting the power supply wires: Connect the VCI-NIS2’s BLACK wire to chassis ground. Connect the RED wire to a
switched +12 volt source. The RED and BLACK wires are the ones coming out from the DC 12V side of the case.
2. Wire the VCI-NIS2’s BLUE wire the vehicle’s +12 volt reverse light supply wire. The reverse wire will show +12 volts when the
vehicle is put into reverse.
3. Connect the Video Back-up Camera’s (optional) video output to the VCI-NIS2s Video 2 input.
(Optional: The VCI-NIS2’s Video 1 input can
be used for a second video backup camera. The toggle switch selects between the radio’s normal display or Video 1 input. Video 2 input has precedence over Video 1 input,
when the blue wire receives +12volts, regardless of the switch position.)
4. Wire the VCI-NIS2’s GREEN wire to the vehicle’s negative parking brake supply wire. The parking brake will show continuity to
ground when the parking brake is on.
5. After all connections have been veried, connect the DB9 harness to the VCI-NIS2 interface and tighten the thumb screws.
Testing the VCI-NIS2:
1. Turn the vehicle and navigation unit on. The navigation display should show normal information.
* If there is no image on the display, check for correct power connection on the VCI-NIS2. Check to be sure molex connectors
are connected securely.
* If the image on the display scrolls across the screen, make sure the molex connectors are connected securely.
2. Temporarily put the vehicle into reverse being careful not to back into anything or anyone. The display screen will change to the
video back-up camera mode. Put vehicle back to Park and the navigation display should show normal information.
*If the navigation map screen disappears and you get a blank screen when the vehicle is put into reverse, check the video
back-up camera for proper power and video cable connection.
NOTE: For use ONLY in vehicles with factory installed navigation or color LCD screen.
Video input accepts only NTSC composite signal. Will NOT work with PAL signal.
Connecting the DB9 Harness:
1. Remove the factory navigation display screen.
2. Disconnect the factory 24 pin plug from the back of the factory display screen.
3. Connect the VCI-NIS2’s 24 pin plug into the back of the factory display screen.
4. Connect the factory 24 pin plug to the VCI-NIS2’s 24 pin harness.
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the VCI-NIS2 parts be held liable for consequential
damages sustained in connection with the VCI-NIS2. The manufacture and it’s distributors will not, nor will they authorize any representative or
any other individual to assume obligation or liability in relation to the VCI-NIS2 other than its replacement.
DB9 harness
Connect to
Factory Harness
Connect to
Factory Display
Black
Red
Nissan / Inniti
Navigation Display
Green: (-) Parking Brake Signal
Blue: (+12VDC) Reverse Signal


Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: VCI-NIS2

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC VCI-NIS2 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret PAC Manualer

PAC

PAC RP4-GM31 Manual

6 September 2024
PAC

PAC NU-CTS2 Manual

6 September 2024
PAC

PAC TR7 Manual

6 September 2024
PAC

PAC OS-5 Manual

6 September 2024
PAC

PAC NDK735MG Manual

29 August 2024
PAC

PAC RP3-GM11 Manual

29 August 2024
PAC

PAC IR-X Manual

29 August 2024
PAC

PAC AAI-GM9 Manual

29 August 2024
PAC

PAC AAI-GM12 Manual

29 August 2024
PAC

PAC CP1-FRD2 Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg

Smeg KIT6PX Manual

23 December 2024
Smeg

Smeg KIT6CX Manual

23 December 2024
Smeg

Smeg GTA-6 Manual

23 December 2024