Panduit CT-2500CHR Manual

Panduit Batterioplader CT-2500CHR

Læs nedenfor 📖 manual på dansk for Panduit CT-2500CHR (2 sider) i kategorien Batterioplader. Denne guide var nyttig for 7 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/2
Page: 1 of 2
CT-2500BC, CT-2500CHR
and CT-2500CHR/E
PA25384A01
Rev. 01 1- 2014
BATTERY CARTRIDGE AND BATTERY CHARGER
USED WITH THE CT-2500 and CT-2500/E TOOLS
OPERATION INSTRUCTIONS
© Panduit Corp. 2014
USE OF THE BATTERY CARTRIDGE AND CHARGING UNIT
The charging unit is run with a nominal voltage of 120 V (CT 2500CHR), or (230 V for -
CT- -2500CHR/E) and a frequency of 50 60 Hz. New batteries must be charged prior to use. To
remove the battery, actuate the battery lock and pull it out of the tool. To charge the battery,
connect the power plug of the charging unit with the power supply and slide the battery into the
charging unit. The charging time is 40 minutes. The charging level of the battery cartridge can be
checked by the right LED (multi color) of the charging unit.-
Left LED (Red) Right LED (Multi -color)
Red Charging unit ready to operate Battery defective
Red Flashing
Charging unit out of order.
New or unused batteries whose
nominal capacity is not sufficient.
Battery too hot or too cold.
Remove battery.
Safety components possibly defective.
Green – Charging cycle starts
Green Flashing –
Battery fully charged.
Charging unit switches automatically into a
maintaining mode. Battery can stay in charger
for indefinite time w/o being damaged.
Yellow
–
Battery at least 90% charged.
Charging cycle can be terminated.
– If the right LED does not light up, the circuit of
the battery is disconnected or the battery is
incorrectly polarized.
• If the nominal capacity of the battery is not achieved, e.g. at first charge, the battery is not
necessarily faulty. Full capacity can be achieved after (3) charging/discharging cycles.
• When the speed of the tool decreases noticeably, the battery must be recharged.
ATTENTION:
Do Not recharge a partially discharged battery as a precaution.
• Charge the battery at room temperature between 50°F and 104°F (10°C and 40°C).
• Charging batteries at low temperatures, under 41°F (5°C) is not possible. Increase battery
temperature before starting the charging cycle.
• Do Not expose the charging unit to rain or snow.
• Do Not charge a battery in the vicinity of explosive materials and gases.
• No other batteries (e.g. dry batteries or car batteries, etc.) are to be used in the tool or in the
charging unit.
• Do Not use the cord to transport the charging unit, or to pull the plug out of a wall socket with
force.
• Do Not insert foreign objects into the ducts of the charging unit. Pull the plug of the charging
unit after charging. Do Not disassemble the charging unit or battery.

Produkt Specifikationer

Mærke: Panduit
Kategori: Batterioplader
Model: CT-2500CHR

Har du brug for hjælp?

Hvis du har brug for hjælp til Panduit CT-2500CHR stil et spørgsmål nedenfor, og andre brugere vil svare dig


Batterioplader Panduit Manualer

Panduit

Panduit CT-2500CHR Manual

7 August 2024

Batterioplader Manualer

Nyeste Batterioplader Manualer

MSW

MSW -CBC-105W-6A Manual

4 Januar 2025
V-TAC

V-TAC S6-EH3P10K2-H Manual

4 Januar 2025
V-TAC

V-TAC VT-48200B Manual

3 Januar 2025
V-TAC

V-TAC S6-EH3P20K-H Manual

3 Januar 2025
V-TAC

V-TAC S6-EH3P15K02-NV-YD-L Manual

3 Januar 2025
V-TAC

V-TAC S6-EH3P15K-H Manual

3 Januar 2025
Kenwood

Kenwood BN-RK510 Manual

1 Januar 2025
Husqvarna

Husqvarna QC300 Manual

31 December 2025
Anker

Anker PowerCore Speed 10000 QC A1266 Manual

30 December 2025
Anker

Anker PowerPort 4 Manual

30 December 2025