Panduit Net-Contain Manual


Læs nedenfor 📖 manual på dansk for Panduit Net-Contain (124 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/124
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014 V00029BZ
Page 1 of 124
Net-Contain Universal Aisle Containment
UNIVERSAL AISLE CONTAINMENT-VERTICAL WALL VERSION
UNIVERSAL AISLE CONTAINMENT-ROOFING VERSION
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 2 of 124
C2CACT5F04SD**
(1) Left Door
(1) Right Door
(1) Transom
(1) Header Assembly
(1)Left Hand Cap
(1) Right Hand Cap
(1) Header Cover
(1) Door Frame
(1) Hardware Kit
COMPONENT GUIDE FOR SLIDING DOORS
C2CACT5F06SD**
(1) Left Door
(1) Right Door
(1) Transom
(1) Header Assembly
(1)Left Hand Cap
(1) Right Hand Cap
(1) Header Cover
(1) Door Frame
(1) Hardware Kit
NET CONTAIN SLIDING DOOR FOR 4FT (1200mm) AISLE
NET CONTAIN SLIDING DOOR FOR 6FT (1800mm) AISLE
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 3 of 124
CUEFRT8F03ST**
(2)End Beam Supports
(1) End Beam
(6) Small Plates
(2) Large Plates
(1) Right Hand Post
(1)Left Hand Post
(1) Right Hand Foot Cover
(1) Left hand Foot Cover
(1) Right Hand 42-45 Support Hanger
(1) Left Hand 42-45 Support Hanger
(1) 900mm CAC Beam
(2) Upper End Panels
(1) Lower Right Hand End Panel
CUEFRT9F03ST**
(2)End Beam Supports
(1) End Beam
(6) Small Plates
(2) Large Plates
(1) Right Hand Post
(1)Left Hand Post
(1) Right Hand Foot Cover
(1) Left hand Foot Cover
(1) Right Hand 48-52 Support Hanger
(1) Left Hand 48-52 Support Hanger
(1) 900mm CAC Beam
(2) Upper End Panels
(1) Lower Right Hand End Panel
(1) Lower Left Hand End Panel
(2) Lower Panel Retainers
(1) Hardware Kit
CUEFRT8F04ST**
(2)End Beam Supports
(1) End Beam
(6) Small Plates
(2) Large Plates
(1) Right Hand Post
(1)Left Hand Post
(1) Right Hand Foot Cover
(1) Left hand Foot Cover
(1) Right Hand 42-45 Support Hanger
(1) Left Hand 42-45 Support Hanger
(1) 1200mm CAC Beam
(1) Hardware Kit
CUEFRT9F04ST**
(2)End Beam Supports
(1) End Beam
(6) Small Plates
(2) Large Plates
(1) Right Hand Post
(1)Left Hand Post
(1) Right Hand Foot Cover
(1) Left hand Foot Cover
(1) Right Hand 48-52 Support Hanger
(1) Left Hand 48-52 Support Hanger
(1) 1200mm CAC Beam
(1) Hardware Kit
CUEFRT8F06ST**
(2)End Beam Supports
(1) End Beam
(6) Small Plates
(2) Large Plates
(1) Right Hand Post
(1)Left Hand Post
(1) Right Hand Foot Cover
(1) Left hand Foot Cover
(1) Right Hand 42-45 Support Hanger
(1) Left Hand 42-45 Support Hanger
(1) 1800mm CAC Beam
(1) Hardware Kit
CUEFRT9F06ST**
(2)End Beam Supports
(1) End Beam
(6) Small Plates
(2) Large Plates
(1) Right Hand Post
(1)Left Hand Post
(1) Right Hand Foot Cover
(1) Left hand Foot Cover
(1) Right Hand 48-52 Support Hanger
(1) Left Hand 48-52 Support Hanger
(1) 1800mm CAC Beam
(1) Hardware Kit
COMPONENT GUIDE FOR END OF ROW FRAMES
NET-CONTAIN UAC END OF ROW FRAME
FOR ROOFING, 42/45RU, 3FT (900mm) AISLE
NET-CONTAIN UAC END OF ROW FRAME
FOR ROOFING, 48/52RU, 3FT (900mm) AISLE
NET-CONTAIN UAC END OF ROW FRAME
FOR ROOFING, 42/45RU, 4FT (1200mm) AISLE
NET-CONTAIN UAC END OF ROW FRAME
FOR ROOFING, 48/52RU, 4FT (1200mm) AISLE
NET-CONTAIN UAC END OF ROW FRAME
FOR ROOFING, 42/45RU, 6FT (1800mm) AISLE
NET-CONTAIN UAC END OF ROW FRAME
FOR ROOFING, 48/52RU, 6FT (1800mm) AISLE
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 4 of 124
CUEFVT8F03ST**
(2)End Beam Supports
(1) End Beam
(6) Small Plates
(2) Large Plates
(1) Right Hand Post
(1)Left Hand Post
(1) Right Hand Foot Cover
(1) Left hand Foot Cover
(1) Right Hand 42-45 Support Hanger
(1) Left Hand 42-45 Support Hanger
(1) 900mm HAC Beam
(2) Upper End Panels
(1) Lower Right Hand End Panel
(1) Lower Left Hand End Panel
(2) Lower Panel Retainers
(1) Hardware Kit
CUEFVT9F03ST**
(2)End Beam Supports
(1) End Beam
(6) Small Plates
(2) Large Plates
(1) Right Hand Post
(1)Left Hand Post
(1) Right Hand Foot Cover
(1) Left hand Foot Cover
(1) Right Hand 48-52Support Hanger
(1) Left Hand 48-52 Support Hanger
(1) 900mm HAC Beam
(2) Upper End Panels
(1) Lower Right Hand End Panel
(1) Lower Left Hand End Panel
(2) Lower Panel Retainers
(1) Hardware Kit
CUEFVT8F04ST**
(2)End Beam Supports
(1) End Beam
(6) Small Plates
(2) Large Plates
(1) Right Hand Post
(1)Left Hand Post
(1) Right Hand Foot Cover
(1) Left hand Foot Cover
(1) Right Hand 42-45 Support Hanger
(1) Left Hand 42-45 Support Hanger
(1) 1200mm HAC Beam
(1) Hardware Kit
CUEFVT9F04ST**
(2)End Beam Supports
(1) End Beam
(6) Small Plates
(2) Large Plates
(1) Right Hand Post
(1)Left Hand Post
(1) Right Hand Foot Cover
(1) Left hand Foot Cover
(1) Right Hand 48-52 Support Hanger
(1) Left Hand 48-52 Support Hanger
(1) 1200mm HAC Beam
(1) Hardware Kit
COMPONENT GUIDE FOR END OF ROW FRAMES
NET-CONTAIN UAC END OF ROW FRAME
FOR VERTICAL WALLS, 42/45RU, 3FT (900mm)
AISLE
NET-CONTAIN UAC END OF ROW FRAME
FOR VERTICAL WALLS, 48/52RU, 3FT (900mm)
AISLE
NET-CONTAIN UAC END OF ROW FRAME
FOR VERTICAL WALLS, 42/45RU, 4FT
(1200mm) AISLE
NET-CONTAIN UAC END OF ROW FRAME
FOR VERTICAL WALLS, 48/52RU, 4FT
(1200mm) AISLE
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 5 of 124
COMPONENT GUIDE WALL BEAM
CUWBSS06ST01**
(1) 600mm Wall Beam
(1) 600mm Wall Beam Clamp
(1) Connector
(1) Wall Beam Ganging Bracket
(Included in Hardware Kit)
(1) Flap Seal
(Included in Hardware Kit)
(1) Hardware Kit
CUWBSS07ST01**
(1) 700mm Wall Beam
(1) 700mm Wall Beam Clamp
(1) Connector
(1) Wall Beam Ganging Bracket
(Included in Hardware Kit)
(1) Flap Seal
(Included in Hardware Kit)
(1) Hardware Kit
NET-CONTAIN UAC WALL BEAM 600mm LONG, 1 PIECE
NET-CONTAIN UAC WALL BEAM 700mm LONG, 1 PIECE
NET-CONTAIN UAC WALL BEAM 600mm LONG, 2 PIECES
CUWBPS06ST02**
(2) 600mm Wall Beams
(2) 600mm Wall Beam Clamps
(2) Connectors
(2) Wall Beam Ganging Brackets
(Included in Hardware Kit)
(2) Flap Seals
(Included in Hardware Kit)
(2) Hardware Kits
NET-CONTAIN UAC WALL BEAM 700mm LONG, 2 PIECES
CUWBPS07ST02**
(2) 700mm Wall Beams
(2) 700mm Wall Beam Clamps
(2) Connectors
(2) Wall Beam Ganging Brackets
(Included in Hardware Kit)
(2) Flap Seals
(Included in Hardware Kit)
(2) Hardware Kits
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 6 of 124
NET-CONTAIN UAC WALL BEAM 2400mm LONG, 1 PIECE
CUWBSS24ST01**
(1) 2400mm Wall Beam
(1) 2400mm Wall Beam Clamp
(1) Connector
(1) Wall Beam Ganging Bracket
(Included in Hardware Kit)
(1) Flap Seal
(Included in Hardware Kit)
(1) Hardware Kit
CUWBSS08ST01**
(1) 800mm Wall Beam
(1) 800mm Wall Beam Clamp
(1) Connector
(1) Wall Beam Ganging Bracket
(Included in Hardware Kit)
(1) Flap Seal
(Included in Hardware Kit)
(1) Hardware Kit
NET-CONTAIN UAC WALL BEAM 800mm LONG, 1 PIECE
CUWBPS08ST02**
(2) 800mm Wall Beams
(2) 800mm Wall Beam Clamps
(2) Connectors
(2) Wall Beam Ganging Brackets
(Included in Hardware Kit)
(2) Flap Seals
(Included in Hardware Kit)
(2) Hardware Kits
NET-CONTAIN UAC WALL BEAM 800mm LONG, 2 PIECES
CUWBPS24ST02**
(2) 2400mm Wall Beams
(2) 2400mm Wall Beam Clamps
(2) Connectors
(2) Wall Beam Ganging Brackets
(Included in Hardware Kit)
(2) Flap Seals
(Included in Hardware Kit)
(2) Hardware Kits
NET-CONTAIN UAC WALL BEAM 2400mm LONG, 2 PIECES
COMPONENT GUIDE WALL BEAM
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 7 of 124
COMPONENT GUIDE FOR CEILING STRUCTURE
CURFS08F06HB**
(1) Aisle Beam
(1) Roof Panel
(1) Hardware Kit
CURFS06F06HB**
(1) Aisle Beam
(1) Roof Panel
(1) Hardware Kit
CURFS07F06HB**
(1) Aisle Beam
(1) Roof Panel
(1) Hardware Kit
CURFS06F04HB**
(1) Aisle Beam
(1) Roof Panel
(1) Hardware Kit
CURFS07F04HB**
(1) Aisle Beam
(1) Roof Panel
(1) Hardware Kit
CURFS08F04HB**
(1) Aisle Beam
(1) Roof Panel
(1) Hardware Kit
NET-CONTAIN UAC 600mm
ROOFING SECTION, 6ft
(1800mm) AISLE
NET-CONTAIN UAC 600mm
ROOFING SECTION, 4ft
(1200mm) AISLE
NET-CONTAIN UAC 700mm
ROOFING SECTION, 6ft
(1800mm) AISLE
NET-CONTAIN UAC 700mm
ROOFING SECTION, 4ft
(1200mm) AISLE
NET-CONTAIN UAC 800mm
ROOFING SECTION, 6ft
(1800mm) AISLE
NET-CONTAIN UAC 800mm
ROOFING SECTION, 4ft
(1200mm) AISLE
NET-CONTAIN UAC 600mm
ROOFING SECTION, 3ft
(900mm) AISLE
NET-CONTAIN UAC 700mm
ROOFING SECTION, 3ft
(900mm) AISLE
NET-CONTAIN UAC 800mm
ROOFING SECTION, 3ft
(900mm) AISLE
CURFS06F03HB**
(1) Aisle Beam
(1) Roof Panel
(1) Hardware Kit
CURFS07F03HB**
(1) Aisle Beam
(1) Roof Panel
(1) Hardware Kit
CURFS08F03HB**
(1) Aisle Beam
(1) Roof Panel
(1) Hardware Kit
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 8 of 124
C2HAC06I1626**
(1) Wall Assembly (600mm Wide)
(2) Diagonal Braces
(1) Brace Bar
(1) Lower Seal
(1) Upper Seal
(1) Hardware Kit
C2HAC07I1626**
(1) Wall Assembly (700mm wide)
(2) Diagonal Braces
(1) Brace Bar
(1) Lower Seal
(1) Upper Seal
(1) Hardware Kit
C2HAC08I1626**
(1) Wall Assembly (800mm wide)
(2) Diagonal Braces
(1) Lower Seal
(1) Upper Seal
(1) Hardware Kit
C2HAC06I2638**
(1) Wall Assembly (600mm Wide)
(2) Diagonal Braces
(1) Brace Bar
(1) Lower Seal
(1) Upper Seal
(1) Hardware Kit
C2HAC07I2638**
(1) Wall Assembly (700mm wide)
(2) Diagonal Braces
(1) Brace Bar
(1) Lower Seal
(1) Upper Seal
(1) Hardware Kit
C2HAC08I2638**
(1) Wall Assembly (800mm wide)
(2) Diagonal Braces
(1) Lower Seal
(1) Upper Seal
(1) Hardware Kit
C2HAC06I3866**
(1) Wall Assembly (600mm Wide)
(2) Diagonal Braces
(1) Brace Bar
(1) Lower Seal
(1) Upper Seal
(1) Hardware Kit
C2HAC07I3866**
(1) Wall Assembly (700mm wide)
(2) Diagonal Braces
(1) Brace Bar
(1) Lower Seal
(1) Upper Seal
(1) Hardware Kit
C2HAC08I3866**
(1) Wall Assembly (800mm wide)
(2) Diagonal Braces
(1) Lower Seal
(1) Upper Seal
(1) Hardware Kit
COMPONENT GUIDE FOR VERTICAL WALL CONTAINMENT
NET-CONTAIN HAC ADJUSTABLE
VERTICAL WALL (38"- 66") 600mm
WIDE
NET-CONTAIN HAC ADJUSTABLE
VERTICAL WALL (38"- 66") 700mm
WIDE
NET-CONTAIN HAC ADJUSTABLE
VERTICAL WALL (38"- 66") 800mm
WIDE
NET-CONTAIN HAC ADJUSTABLE
VERTICAL WALL (26"- 38") 600mm
WIDE
NET-CONTAIN HAC ADJUSTABLE
VERTICAL WALL (26"- 38") 700mm
WIDE
NET-CONTAIN HAC ADJUSTABLE
VERTICAL WALL (26"- 38") 800mm
WIDE
NET-CONTAIN HAC ADJUSTABLE
VERTICAL WALL (16"- 26") 600mm
WIDE
NET-CONTAIN HAC ADJUSTABLE
VERTICAL WALL (16"- 26") 700mm
WIDE
NET-CONTAIN HAC ADJUSTABLE
VERTICAL WALL (16"- 26") 800mm
WIDE
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 9 of 124
CUVWB09S09ST**
(1) 900mm Vertical Wall Brace
(1) Hardware Kit
CUVWA08S08ST**
(2) HAC Diagonal Braces
(1) 800mm HAC Adapter
(1) Hardware Kit
CUVWA07S07ST**
(2) HAC Diagonal Braces
(1) 700mm HAC Adapter
(1) Hardware Kit
CUVWA06S06ST**
(2) HAC Diagonal Braces
(1) 600mm HAC Adapter
(1) Hardware Kit
CUVWB12S12ST**
(1) 1200mm Vertical Wall Brace
(1) Hardware Kit
COMPONENT GUIDE FOR WALL ADAPTERS AND VERTICAL WALL BRACES
NET-CONTAIN UAC VERTICAL WALL
ADAPTER, 600mm WIDE
NET-CONTAIN UAC VERTICAL WALL
ADAPTER, 700mm WIDE
NET-CONTAIN UAC VERTICAL WALL
ADAPTER, 800mm WIDE
NET-CONTAIN UAC VERTICAL WALL BRACE,
3FT (900mm) AISLE
NET-CONTAIN UAC VERTICAL WALL BRACE,
4FT (1200mm) AISLE
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 10 of 124
C2HACERI1626**
(2) Center Frames
(2) Center Cross Beams
(1) Upper Right Cross Beam
(1) Upper Left Cross Beam
(1) Lower Right Cross Beam
(1) Lower Left Cross Beam
(4) 200mm Panel Clamps
(6) 40mm Panel Clamps
(1) 1626 Clear Panel
(1) Hardware Kit
C2HACERI2638**
(2) Center Frames
(2) Center Cross Beams
(1) Upper Right Cross Beam
(1) Upper Left Cross Beam
(1) Lower Right Cross Beam
(1) Lower Left Cross Beam
(6) 200mm Panel Clamps
(4) 40mm Panel Clamps
(1) 2638 Clear Panel
(1) Hardware Kit
C2HACERI3866**
(2) Center Frames
(2) Center Cross Beams
(1) Upper Right Cross Beam
(1) Upper Left Cross Beam
(1) Lower Right Cross Beam
(1) Lower Left Cross Beam
(8) 200mm Panel Clamps
(6) 100mm Panel Clamps
(2) Side Clamps
(2) 3866 Clear Panels
(1) H Channel
(1) Hardware Kit
COMPONENT GUIDE FOR END OF ROW WALL
NET-CONTAIN HAC ADJUSTABLE
END OF ROW VERTICAL WALL
(16"- 26")
NET-CONTAIN HAC ADJUSTABLE
END OF ROW VERTICAL WALL
(26"- 38")
NET-CONTAIN HAC ADJUSTABLE
END OF ROW VERTICAL WALL
(38"- 66")
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 11 of 124
CUFBPR4206HB**
(1) 42RU Blanking Panel
(1) Wiring Duct
(1) Hardware Kit
CUFBPR4506HB**
(1) 45RU Blanking Panel
(1) Wiring Duct
(1) Hardware Kit
CUFBPR4806HB**
(1) 48RU Blanking Panel
(1) Wiring Duct
(1) Hardware Kit
CUFBPR5206HB**
(1) 52RU Blanking Panel
(1) Wiring Duct
(1) Hardware Kit
CUTBPR0610HB**
(1) 600mm Blanking Panel
(1) Wiring Duct
(1) Hardware Kit
COMPONENT GUIDE FOR BLANKING PANELS
NET-CONTAIN UAC FULL
BLANKING PANEL 42RU X
600mm WIDE
NET-CONTAIN UAC FULL
BLANKING PANEL 45RU X
600mm WIDE
NET-CONTAIN UAC FULL
BLANKING PANEL 48RU X
600mm WIDE
NET-CONTAIN UAC FULL BLANKING
PANEL 52RU X 600mm WIDE
NET-CONTAIN UAC TOP OF CABINET
BLANKING PANEL 600mm HIGH X 1000mm
WIDE
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 12 of 124
CUSMPR52ST01**
(1) Support Bracket
(1) Support Post
(2) Plates
(1) Hardware Kit
CUCMSS03ST01NC
(1) 300mm Long Threaded Rod
(1) Swivel Leveling Mount
(1) Hardware Kit
CUCMSS06ST01NC
(1) 600mm Long Threaded Rod
(1) Swivel Leveling Mount
(1) Hardware Kit
COMPONENT GUIDE FOR MID ROW SUPPORT
NET-CONTAIN UAC MID-SPAN POST
42RU to 52RU HIGH
NET-CONTAIN UAC MID-SPAN
CABINET SUPPORT, 300mm HIGH
NET-CONTAIN UAC MID-SPAN
CABINET SUPPORT, 600mm HIGH
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 13 of 124
Table of Contents
Section 1 - Installation Universal End of Row Frame
Attaching Hanger and Beam Support to Post (For 900mm 42RU Set-Up Only).....................................................................
Attaching Hanger and Beam Support to Post (For 900mm 45RU Set-Up Only).....................................................................
Attaching Hanger and Beam Support to Post (For 900mm 48RU Set-Up Only).....................................................................
Attaching Hanger to Post (For 900mm 52RU Set-Up Only)....................................................................................................
Attaching Beam Support and Spacer to Post (For 900mm 52RU Set-Up Only)......................................................................
Attaching Hanger and Beam Support to Post (For 1200mm 42RU Set-Up Only)...................................................................
Attaching Hanger and Beam Support to Post (For 1200mm 45RU Set-Up Only)...................................................................
Attaching Hanger and Beam Support to Post (For 1200mm 48RU Set-Up Only)...................................................................
Attaching Hanger to Post (For 1200mm 52RU Set-Up Only)..................................................................................................
Attaching Beam Support and Spacer (For 1200mm 52RU Set-Up Only)................................................................................
Attaching Hanger and Beam Support to Post (For 1800mm 42RU Set-Up Only)...................................................................
Attaching Hanger and Beam Support to Post (For 1800mm 45RU Set-Up Only)...................................................................
Attaching Hanger and Beam Support to Post (For 1800mm 48RU Set-Up Only)...................................................................
Attaching Hanger to Post (For 1800mm 52RU Set-Up Only)..................................................................................................
Attaching Beam Support and Spacer (For 1800mm 52RU Set-Up Only)................................................................................
Containment System Layout....................................................................................................................................................
Attaching Post to Floor............................................................................................................................................................
Install Post Foot Cover.............................................................................................................................................................
Attaching End of Row Beam (For 900mm and 1200mm Aisles, 42RU-45RU Set-Up Only)..................................................
Attaching End of Row Beam (For 900mm and 1200mm Aisles, 48RU-52RU Set-Up Only)..................................................
Attaching End of Row Beam (For 900mm and 1200mm Aisles, 42RU-45RU Set-Up Only)..................................................
Attaching End of Row Beam (For 900mm and 1200mm Aisles, 48RU-52RU Set-Up Only)..................................................
Attaching Vertical Wall End of Row Beam (For Vertical Wall Set-Up Only)..........................................................................
Attaching Foam Seal to Vertical Wall End of Row Beam (For Vertical Wall Only)................................................................
Attaching Support Hanger (For 900mm Vertical Wall Set-Up Only).......................................................................................
Attaching Support Bracket (For 1200mm Vertical Wall Set-Up Only)....................................................................................
Attaching Support Hanger (For 900mm Roofing Set-Up Only)..............................................................................................
Attaching Upper End Panel (For 900mm Aisle Only)..............................................................................................................
Attaching Lower End Panel (For 900mm Aisle Only).............................................................................................................
Attaching Lower End Panel Brace (For 900mm Aisle Only)...................................................................................................
Grounding the End-of-Row Frame...........................................................................................................................................
Section 2 - Installation of Wall Beams, Mid-Span Support Post
and Mid-Span Cabinet Support Rod
Aligning Wall Beams................................................................................................................................................................
Attaching Wall Beam Connector..............................................................................................................................................
Attaching Wall Beam Ganging Bracket...................................................................................................................................
Mid-Span Support for Wall Beams...........................................................................................................................................
Supporting Wall Beams using Mid-Span Cabinet Support.......................................................................................................
Supporting Wall Beams using Threaded Rod...........................................................................................................................
Locating Mid-Span Support Post.............................................................................................................................................
Attaching Support Bracket to Support Post..............................................................................................................................
Attaching Support Post to Floor...............................................................................................................................................
Attaching Wall Beam Assembly to End of Row Frames.........................................................................................................
Securing Wall Beam (For 900mm Vertical Wall Containment Set-Up Only)...........................................................................
Securing Wall Beam (For 900mm Roofing Containment Set-Up Only)..................................................................................
Securing Wall Beam (For 1200 Vertical Wall Containment Set-Up Only)..............................................................................
Securing Wall Beam (For 1200 Roofing Containment Set-Up Only)......................................................................................
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
50
51
52
53
53
53
54
55
56
57
58
59
60
61
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 14 of 124
66
67
68
69
71
72
73
74
75
76
77
78
79
80
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
Table of Contents
Section 2 (continued)- Installation of Wall Beams, Mid-Span
Support Post and Mid-Span Cabinet Support Rod
Attaching Roofing Beam (For Roofing Containment Set-Up Only)........................................................................................
Installing Wall Beam Clamp.....................................................................................................................................................
Attaching Flap Seal to Wall Beam Clamp................................................................................................................................
Section 3 - Installation of Roofing
Installing Aisle Containment Roofing Aisle Beam..................................................................................................................
Placing Ceiling Panel...............................................................................................................................................................
Securing Aisle Containment Roofing Aisle Beam...................................................................................................................
Securing Ceiling Panel.............................................................................................................................................................
Section 4 - Installation of Vertical Walls, Vertical Wall Adapter
and Vertical Wall Brace
Installing Vertical Wall Brace...................................................................................................................................................
Installing Vertical Wall Adapter................................................................................................................................................
Attaching Wall Brace to Vertical Wall......................................................................................................................................
Applying Foam Seal to Vertical Wall.......................................................................................................................................
Installing Vertical Wall.............................................................................................................................................................
Setting Wall Panel Height........................................................................................................................................................
Sizing Upper Seal.....................................................................................................................................................................
Attaching Upper Seal................................................................................................................................................................
Attaching Foam to Lower Seal.................................................................................................................................................
Attaching Lower Seal...............................................................................................................................................................
Section 5 - Installation of End of Row Vertical Wall
Attaching Lower Side Frame....................................................................................................................................................
Attaching Lower Cross Beams.................................................................................................................................................
Attaching Upper Cross Beams.................................................................................................................................................
Attach Foam Seal to Upper Side Frame...................................................................................................................................
Attaching Upper Side Frame....................................................................................................................................................
Attach Center Cross Beams......................................................................................................................................................
Attach Center Frames...............................................................................................................................................................
Assemble H Channel [For End of Row Adjustable Vertical Wall, 38"- 66" (C2HACERI3866 Only)]....................................
Attach H Channel to Center Frame [For End of Row Adjustable Vertical Wall, 38" - 66" (C2HACERI3866 Only)].............
Mark and Cut H Channel [For End of Row Adjustable Vertical Wall, 38" - 66" (C2HACERI3866 Only)]............................
Measure and Cut Wall Panel....................................................................................................................................................
Attaching H Channel to Clear Panels [For End of Row Adjustable Vertical Wall, 38" - 66" (C2HACERI3866 Only)]..........
Attach Bottom and Side Wall Panel Clamps............................................................................................................................
Insert Wall Panel......................................................................................................................................................................
Attach Top and Remaining Side Wall Panel Clamps...............................................................................................................
Foam Seal Installation..............................................................................................................................................................
62
63
64
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 15 of 124
Table of Contents
Section 6 - Installation of Net-Contain Sliding Doors
Attaching Transom...................................................................................................................................................................
Flap Seal Installation................................................................................................................................................................
Attaching Vertical Panel (for 900mm/1200mm Aisles)...........................................................................................................
Attaching Vertical Panel (for 1800mm Aisles Only)................................................................................................................
Panel Cover Installation (for 900mm/1200mm Aisles)............................................................................................................
Panel Cover Installation (for 1800mm Aisles).........................................................................................................................
Attaching Door Guides.............................................................................................................................................................
Header Installation....................................................................................................................................................................
Right Hand Sliding Door Set-Up..............................................................................................................................................
Left Hand Sliding Door Set-Up................................................................................................................................................
Sliding Door Installation..........................................................................................................................................................
Adjusting Sliding Door Height.................................................................................................................................................
Adjusting Door Seals................................................................................................................................................................
Adjusting Door Damper...........................................................................................................................................................
Attaching Cover Caps...............................................................................................................................................................
Header Cover Installation.........................................................................................................................................................
Section 7 - Installation of Blanking Panels
Cutting Blanking Panels...........................................................................................................................................................
Placing First Lower Guide........................................................................................................................................................
Additional Lower Guides.........................................................................................................................................................
Blanking Panel Installation.......................................................................................................................................................
Over Lapping Blanking Panels.................................................................................................................................................
Sizing Above Cabinet Blanking Panel.....................................................................................................................................
Placing Lower Guide (For Above Cabinet Blanking Panel Only)............................................................................................
Blanking Panel Installation (For Above Cabinet Blanking Panel Only)..................................................................................
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
116
117
118
119
120
121
122
123
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 16 of 124
SECTION 1
INSTALLATION OF UNIVERSAL
END OF ROW FRAME
CUEFRT8F03STB1,CUEFRT9F03STB1,CUEFRT8F04STB1,
CUEFRT9F04STB1,CUEFRT8F06STB1,CUEFRT9F06STB1,
CUEFVT8F03STB1,CUEFVT9F03STB1,CUEFVT8F04STB1,
CUEFVT9F04STB1
Roofing
Vertical Wall
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 17 of 124
Attaching Hanger and Beam Support to Post
(For 900mm 42RU Set-Up Only)
Using (2) M6 nuts, secure the left hanger to the left side post.
Attach (1) beam support to the left hand post and left hand hanger with (2) M6 nuts.
Repeat process for right side post.
(2) M6 Nuts
Beam Support
Hanger
Left Post Right Post
42RU Alignment-
Hanger
(2) M6 Nuts
Beam Support
42RU Alignment-
Beam Support
Hanger
(2) M6 Nuts
42RU Alignment-
Hanger
(2) M6 Nuts
42RU Alignment-
Beam Support
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 18 of 124
Left Post Right Post
Hanger
(2) M6 Nuts
45RU Alignment-
Hanger
(2) M6 Nuts
Beam Support
45RU Alignment-
Beam Support
Attaching Hanger and Beam Support to Post
(For 900mm 45RU Set-Up Only)
Using (2) M6 nuts, secure the left hanger to the left side post.
Attach (1) beam support to the left hand post and left hand hanger with (2) M6 nuts.
Repeat process for right side post.
(2) M6 Nuts
Beam Support
45RU Alignment-
Beam Support
Hanger
(2) M6 Nuts
45RU Alignment-
Hanger
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 19 of 124
Attaching Hanger and Beam Support to Post
(For 900mm 48RU Set-Up Only)
Using (4) M6x12mm bolts, secure the left hanger to the outside of the left side post.
Secure the left hanger in place with (2) M6x12mm bolts to the inside of the left side post.
Attach (1) beam support to the left side post and left hanger with (2) M6 nuts.
Repeat process for right side post.
Hanger (2) M6 Nuts
Beam Support
(4) M6x12mm
Bolts
(2) M6x12mm
Bolts
Left Side Post Left Side Post-
Outside Wall Left Side Post-
Inside Wall
Right Side Post
Right Side Post-
Outside Wall
Right Side Post-
Inside Wall
(4) M6x12mm
Bolts
Hanger (2) M6 Nuts
Beam Support
(2) M6x12mm
Bolts
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 20 of 124
Attaching Hanger to Post
(For 900mm 52RU Set-Up Only)
Using (4) M6x12mm bolts, secure the left hanger to the left side post from the outside of the post.
Secure the left hanger in place with (4) M6x12mm bolts to the inside of the left side post.
Repeat process for right side post.
Left Hanger
(4) M6x12mm
Bolts
(4) M6x12mm
Bolts
Right Hanger
Left Post
Right Post
Left Post-
Inside
Right Post-
Inside
Left Post-
Outside
(4) M6x12mm
Bolts
Right Post-
Outside
(4) M6x12mm
Bolts
Right Hanger
Left Hanger
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 21 of 124
Attaching Beam Support and Spacer to Post
(For 900mm 52RU Set-Up Only)
Attach (1) beam support and spacer to the left hand post and hanger with (2) M6 nuts.
Repeat process for right side post.
Hanger
(2) M6 Nuts
Beam Support
Spacer
Left Post-
Assembly
Left Post
Hanger
Beam Support
Spacer
Left Post
Right Post-
Assembly
Hanger
Beam
Support
Spacer
Right Post
Hanger
Beam
Support
Spacer
Right Post
(2) M6
Nuts
View-Top of Left Post
View-Top of Right Post
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 22 of 124
Attaching Hanger and Beam Support to Post
(For 1200mm 42RU Set-Up Only)
Using (2) M6x12mm bolts, secure the left hanger to the left side post.
Attach (1) support beam to the left side post and left hanger with (2) M6 nuts.
Repeat process for right side post.
Hanger
(2) M6x12mm
Bolts
Beam
Support
(2) M6 Nuts
Beam Support
Hanger
Left Post
Right Post
Left Post-Outside
Face
Hanger
Right Post-
Outside Face
Hanger (2) M6 Nuts
Left Post-Outside
Face
Right Post-
Outside Face
(2) M6x12mm
Bolts
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 23 of 124
Attaching Hanger and Beam Support to Post
(For 1200mm 45RU Set-Up Only)
Using (2) M6x12mm bolts, secure the left hanger to the left side post.
Attach (1) support beam to the left side post and left hanger with (2) M6 nuts.
Repeat process for right side post.
Left Post
Right Post
(2) M6x12mm
Bolts
Beam Support
Hanger
Left Post-Outside
Face
Hanger (2) M6 Nuts
Left Post-Outside
Face
Hanger
Beam
Support
(2) M6 Nuts
Hanger
Right Post-
Outside Face
Right Post-
Outside Face
(2) M6x12mm
Bolts
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 24 of 124
Attaching Hanger and Beam Support to Post
(For 1200mm 48RU Set-Up Only)
Using (4) M6x12mm bolts, secure the right hanger to the outside of the right side post.
Secure the hanger in place with (2) M6x12mm bolts to the inside of the right side post.
Attach (1) support beam to the right side post and hanger with (2) M6 nuts.
Repeat process for left side post.
Hanger
(4) M6x12mm
Bolts
Beam
Support
(2) M6 Nuts
(2) M6x12mm
Bolts
Left Post
Right Post
Hanger
Left Post-Inside
Face
Left Post-Outside
Face
(4) M6x12mm
Bolts
Right Post-Inside
Face
Hanger
Beam
Support
(2) M6 Nuts
(2) M6x12mm
Bolts
Hanger
Right Post-
Outside Face
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 25 of 124
Attaching Hanger to Post
(For 1200mm 52RU Set-Up Only)
Using (4) M6x12mm bolts, secure the left hanger to the outside of the left side post.
Secure the left hanger in place with (4) M6x12mm bolts to the inside of the left side post.
Repeat process for right side post.
Hanger
(4) M6x12mm
Bolts
(4) M6x12mm
Bolts
Left Post
Hanger
Right Post
(4) M6x12mm
Bolts
(4) M6x12mm
Bolts
HangerHanger
Left Post-
Outside
Left Post-
Inside
Right Post-
Inside
Right Post-
Outside
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 26 of 124
Attaching Beam Support and Spacer
(For 1200mm 52RU Set-Up Only)
Attach (1) beam support and spacer to the left side post and hanger with (2) M6 nuts.
Repeat process for right side post.
(2) M6 Nuts
Beam Support
Spacer
Hanger
Left Post
Left Post-
Inside
Right Post-
Inside
Beam Support
Spacer
Hanger
(2) M6 Nuts
Right Post
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 27 of 124
Attaching Hanger and Beam Support to Post
(For 1800mm 42RU Set-Up Only)
Using (2) M6x12mm bolts, secure the left hanger to the left side post.
Attach (1) support beam to the left side post and left hanger with (2) M6 nuts.
Repeat process for right side post.
Hanger
(2) M6x12mm
Bolts
Beam
Support
(2) M6 Nuts
Beam Support
Hanger
Left Post Left Post-Outside
Face
Hanger
Right Post-
Outside Face
Hanger (2) M6 Nuts
Left Post-Outside
Face
Right Post-
Outside Face
(2) M6x12mm
Bolts
Right Post
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 28 of 124
Attaching Hanger and Beam Support to Post
(For 1800mm 45RU Set-Up Only)
Using (2) M6x12mm bolts, secure the left hanger to the left side post.
Attach (1) support beam to the left side post and left hanger with (2) M6 nuts.
Repeat process for right side post.
Left Post
Right Post
(2) M6x12mm
Bolts
Beam Support
Hanger
Left Post-Outside
Face
Hanger (2) M6 Nuts
Left Post-Outside
Face
Hanger
Beam
Support
(2) M6 Nuts
Hanger
Right Post-
Outside Face
Right Post-
Outside Face
(2) M6x12mm
Bolts
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 29 of 124
Attaching Hanger and Beam Support to Post
(For 1800mm 48RU Set-Up Only)
Using (4) M6x12mm bolts, secure the right hanger to the outside of the right side post.
Secure the hanger in place with (2) M6x12mm bolts to the inside of the right side post.
Attach (1) support beam to the right side post and hanger with (2) M6 nuts.
Repeat process for left side post.
Hanger
(4) M6x12mm
Bolts
Beam
Support
(2) M6 Nuts
(2) M6x12mm
Bolts
Left Post
Right Post
Hanger
Left Post-Inside
Face
Left Post-Outside
Face
(4) M6x12mm
Bolts
Right Post-Inside
Face
Hanger
Beam
Support
(2) M6 Nuts
(2) M6x12mm
Bolts
Hanger
Right Post-
Outside Face
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 30 of 124
Attaching Hanger to Post
(For 1800mm 52RU Set-Up Only)
Using (4) M6x12mm bolts, secure the left hanger to the outside of the left side post.
Secure the left hanger in place with (4) M6x12mm bolts to the inside of the left side post.
Repeat process for right side post.
Hanger
(4) M6x12mm
Bolts
(4) M6x12mm
Bolts
Left Post
Hanger
Right Post
(4) M6x12mm
Bolts
(4)
M6x12mm
Bolts
HangerHanger
Left Post-
Outside
Left Post-
Inside
Right Post-
Inside
Right Post-
Outside
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 31 of 124
Attaching Beam Support and Spacer
(For 1800mm 52RU Set-Up Only)
Attach (1) beam support and spacer to the left side post and hanger with (2) M6 nuts.
Repeat process for right side post.
(2) M6 Nuts
Beam Support
Spacer
Hanger
Left Post
Left Post-
Inside
Right Post-
Inside
Beam Support
Spacer
Hanger
(2) M6 Nuts
Right Post
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 32 of 124
692mm
(27.25”)
Length of
containment
system
(measured from
inside of posts)
Center of
Contained Aisle
Detail A
32mm
(1.26”)
Containment System Layout
The containment system length is measured from inside of posts, as shown below.
The drill layout shown below applies to all aisle widths (900mm, 1200mm, and 1800mm).
(6) 8mm (5/16")
Clearance Holes 150mm
(5.9") 150mm
(5.9")
30mm (1.18")
Detail A
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 33 of 124
Containment System Layout
900mm (3ft) Aisle 1200mm (4ft) Aisle
1800mm (6ft) Aisle
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 34 of 124
Attaching Post to Floor
From the floor, remove a tile that is directly next to the tile that you will be attaching the post to.
Have (1) person hold the post in place aligning the holes in the foot with the pilot holes in the tile.
Have another person insert (6) M6x50mm hex head bolts through (3) foot plates on the top of the foot of the
post.
From underneath the tile slide (1) tile plate over the (6) M6x50mm hex head bolts and secure into place with
(6) M6 nuts.
900mm and 1200mm Aisle Posts
1800mm Aisle Posts
(6) M6x50mm
Hex Head Bolts
(6) M6x50mm
Hex Head Bolts
(6) M6 Nuts
(6) M6 Nuts
(3) Foot
Plates
(3) Foot
Plates
(1) Tile Plate
(1) Tile Plate
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 35 of 124
Install Post Foot Cover
From the side, slide the foot cover over the post foot.
Secure foot cover in place with (2) M5x10mm hex head screws.
Repeat process for second post.
Foot Cover
Foot Cover
(2) M5x10mm Hex
Head Screws
(2) M5x10mm Hex
Head Screws
900mm and 1200mm Aisle
1800mm Aisle
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 36 of 124
Attaching End of Row Beam
(For 900mm and 1200mm Aisles, 42RU-45RU Set-Up Only)
Attach an end of row beam to the (2) beam supports with (2) M6 nuts at each end.
End of Row Beam
(2) Beam
Supports
42RU Setup View
Left Side
Post
Right Side
Post
End of Row Beam (2) M6 Nuts
Each End
Detail View
45RU Setup View Detail View
(2) Beam
Supports
Left Side
Post
Right Side
Post
(2) M6 Nuts
Each End End of Row Beam
End of Row Beam
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 37 of 124
Attaching End of Row Beam
(For 900mm and 1200mm Aisles, 48RU-52RU Set-Up Only)
Attach an end of row beam to the (2) end of beam support brackets with (4) M6 nuts.
End of Row
Beam
Beam Support
(1) at each end
(2) M6 Nuts
Each End
(2) M6 Nuts
Each End
Detail View
Detail View
52RU Setup View
End of Row Beam
(2) Beam
Supports
Left Side
Post
Right Side
Post
48RU Setup View
45RU Setup View
End of Row
Beam
(2) Beam
Supports
Left Side
Post Right Side
Post
End of Row Beam
Beam Support
(1) at each end
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 38 of 124
Attaching End of Row Beam
(For 1800mm Aisles, 42RU-45RU Set-Up Only)
Attach an end of row beam to the (2) beam supports with (2) M6 nuts at each end.
End of Row Beam
(2) Beam
Supports
42RU Setup View
Left Side
Post
Right Side
Post
End of Row Beam (2) M6 Nuts
Each End
Detail View
45RU Setup View Detail View
(2) Beam
Supports
Left Side
Post
Right Side
Post
(2) M6 Nuts
Each End End of Row Beam
End of Row Beam
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 39 of 124
Attaching End of Row Beam
(For 1800mm Aisles, 48RU-52RU Set-Up Only)
Attach an end of row beam to the (2) end of beam support brackets with (4) M6 nuts.
End of Row
Beam
(2) M6 Nuts
Each End
(2) M6 Nuts
Each End
Detail View
Detail View
52RU Setup View
End of Row Beam
(2) Beam
Supports
Left Side
Post
Right Side
Post
48RU Setup View
End of Row
Beam
(2) Beam
Supports
Left Side
Post
Right Side
Post
End of Row Beam
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 40 of 124
Attaching Vertical Wall End of Row Beam
(For Vertical Wall Set-Up Only)
Attach a hot aisle containment end of row beam to the top of the end of row beam with (5) M5x10mm
screws.
(5) M5x10mm Screws
Vertical Wall End of
Row Beam
Front View-End of Row Frame
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 41 of 124
Applying Foam Seal to Vertical Wall End Beam
(For Vertical Wall Set-Up Only)
Apply (1) strip of foam seal along the top edge of the Vertical Wall end beam from one end to the other.
Vertical Wall
End Beam
Foam Seal
Detail View-Foam Attached
Rear View-End of Row Frame
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 42 of 124
Attaching Support Hanger
(For 900mm Vertical Wall Set-Up Only)
Place the left support hanger on top of the left hanger.
Secure the left support hanger to the Vertical Wall end beam with (2) M5x10mm screws.
Repeat process for right support hanger.
(2) M5x10mm
Screws
Right
Support
Hanger
Vertical Wall
End Beam
Vertical Wall
End Beam
(2) M5x10mm
Screws
Left
Support
Hanger
Left Post
Right Post
Rear View-End of Row Frame
Rear View-End of Row Frame
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 43 of 124
Attaching Support Bracket
(For 1200mm Vertical Wall Set-Up Only)
Attach (1) wall beam support bracket to each end of the Vertical Wall with (2) M5x10mm screws each.
(2) M5x10mm
Screws
Wall Beam Support
Bracket
(2) M5x10mm
Screws
Wall Beam Support
Bracket
Left Post
Right Post
Rear View-End of Row Frame
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 44 of 124
Attaching Support Hanger
(For 900mm Roofing Set-Up Only)
Place the left support hanger on top of the left hanger.
Secure the support hanger to the end of row beam with (1) M5x10mm screw.
Repeat process for right support hanger.
(1) M5x10mm
Screw Right Support
Hanger
Right Hanger
Right
Post
(1) M5x10mm
Screw
Left Support
Hanger
Right Hanger
Left Post
Rear View-End of Row Frame
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 45 of 124
Attaching Upper End Panel (For 900mm Aisle Only)
Using (2) M5 nuts, attach an upper end panel to the bottom of the right side end of row beam support bracket.
Repeat Process for left side end of row beam support bracket.
Upper End
Panel
(2) M5 Nuts
End of Row
Beam Support
Bracket
Rear View-End of Row Frame
(2) M5 Nuts
End of Row
Beam Support
Bracket
Upper End
Panel
Right Post Left Post
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 46 of 124
Attaching Lower End Panel (For 900mm Aisle Only)
Using (2) M5 nuts, attach a lower end panel to the upper end panel on left side of frame.
Repeat process for right side.
(2) M5 Nuts
Lower End
Panel
Upper End
Panel
Front View-End of Row Frame
Left Post Right Post
(2) M5 Nuts
Lower End
Panel
Upper End
Panel
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 47 of 124
Attaching Lower End Panel Brace (For 900mm Aisle Only)
Attach a lower end panel brace to the lower end panel with (2) M5 nuts making sure that the lower end panel
brace wraps around the post.
Repeat process for left side.
(2) M5 Nuts
Lower End
Panel
Lower End
Panel Brace
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 48 of 124
Grounding the End-of-Row Frame
The end-of-row frame can be grounded at either the top or bottom of the vertical posts. A common bonding
network (CBN) jumper kit can be attached to any of the points noted below.
(2) M5x10mm Hex
Head Screws
(either one)
(2) M6x12mm
Bolts
(either one)
Top of Vertical Post
Bottom of Vertical Post
(900/1200mm Setup)
Bottom of Vertical Post
(1800mm Setup)
(2) M5x10mm Hex
Head Screws
(either one)
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 49 of 124
SECTION 2
INSTALLATION OF WALL BEAM,
MID-SPAN SUPPORT POST
AND
MID-SPAN CABINET SUPPORT
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 50 of 124
X
X
X
XX
Aligning Wall Beams
Place the required number of wall beams next to each other, end to end.
Ensure that wall beams are matching lengths on both sides of the aisle.
i.e. 600mm wall beam across from 600mm beam; 2400mm wall beam across from 2400mm beam, etc.
Wall Beams
CORRECT
Matching
lengths on
both sides
of aisle
NOT CORRECT
Wall beams are NOT matching
lengths on both sides of aisle
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 51 of 124
Attaching Wall Beam Connector
Place the wall beam connector in between (2) wall beams so that the (8) studs pass through the wall beam
connector.
Fasten the wall beam connector to the (2) wall beams with (8) M6x12mm bolts.
Secure the wall beam connector in place with (8) M6 hex nuts.
Wall Beam
Connector
(8) M6 Hex Nuts(8) M6x12mm
Bolts
Wall Beams
VIEW SHOWS BACK
OF WALL BEAMS
Wall Beam
Connector
PORTIONS OF WALL BEAMS HAVE
BEEN CUT AWAY TO ENHANCE VIEW
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 52 of 124
Attaching Wall Beam Ganging Bracket
Attach (1) wall beam ganging bracket in between every pair of wall beams with (2) M5x12mm button head
screws.
Wall Beam
Ganging
Bracket
(2) M5x12mm
Button Head
Screws
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 53 of 124
Mid-Span Support for Wall Beams
Panduit recommends a mid-span support every 3,600mm (11.8’). The maximum distance without a mid-span
support is 4,800mm (16’).
Wall beams can be supported using any of the following:
--Mid-span cabinet support
--Threaded rod suspended from the ceiling
--Mid-span support post
Supporting Wall Beams using Mid-Span Cabinet Support
Thread the mid-span cabinet support rod through a M12 hex nut, a 1/2" washer, the wall beam, then through
another 1/2" washer, M12 hex nut and finally into the swiveling level mount.
View From Top View From Side
Rod
(2) M12 Hex
Nuts
(2) 1/2"
Washers
Swiveling
Level Mount
Supporting Wall Beams using Threaded Rod
Wall beams can be supported using threaded rod suspended from the ceiling. Threaded rod can be attached
using the same holes as the Mid-Span cabinet support shown above.
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 54 of 124
Locating Mid-Span Support Post
See detail view shown below for dimensions for drilling pilot holes for Mid-Span support posts.
BOTTOM VIEW
(looking up from floor)
NOTE: Views are not shown to scale to
help illustrate dimensional requirements
566.9mm (22.32") 900mm Aisles
680.5mm (26.79") 1200mm Aisles
980.5mm (38.60") 1800mm Aisles
118mm
30mm
(4) 8.0mm (5/16")
Clearance Holes.
Detail View
Center of Contained Aisle
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 55 of 124
Attaching Support Bracket to Support Post
Attach support bracket to support post using (4) M6 X 12mm Hex Bolts.
See chart below for orientation of holes for 42RU, 45RU, 48RU, and 52RU setups.
Repeat process for every support post required.
42RU Setup 45RU Setup
48RU Setup 52RU Setup
(4) M6X12mm
Hex Bolts
(4) M6X12mm
Hex Bolts
(4) M6X12mm
Hex Bolts (4) M6X12mm
Hex Bolts
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 56 of 124
Attaching Support Post to Floor
From the floor, remove a tile that is directly next to the tile that you will be attaching the support post to.
Have (1) person hold the support post in place aligning the holes in the foot with the pilot holes in the tile.
Have another person insert (4) M6x50 hex head bolts through the foot of the support post.
From underneath the tile slide (2) tile plates over the (4) M6x50 hex head bolts and secure into place with (6)
M6 nuts.
Repeat process for every support post required.
(4) M6x50 Hex
Head Bolts
(4) M6 Nuts
(2) Tile Plate
Toward Center of Aisle
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 57 of 124
Attaching Wall Beam Assembly to End of Row Frames
(A Minimum of 2 People are Required for this Step.)
Lift (1) wall beam assembly above the end of row frames.
Lower the wall beam assembly onto the hanger bracket.
Secure wall beam assembly in to each hanger bracket with a total of (6) M6 hex nuts.
If required fasten wall beam assembly to mid-span support post with (2) M6 hex nuts.
Wall Beam
Assembly
(6) M6 hex nuts
Hanger Bracket
Mid-Span
Support Post
Wall Beam
Assembly
(2) M6 hex nuts
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 58 of 124
Securing Wall Beam
(For 900mm Vertical Wall Containment Set-Up Only)
Fasten (1) M5x10mm screw through the wall beam bracket into the wall beam from the inside of the aisle.
Fasten (3) M6x12mm bolts and (3) M6 nuts to the hanger and wall beam.
Repeat process for every hanger.
Hanger
Wall Beam
Bracket
M5x10mm
Screw
M6x12mm
Bolt
M6 Nut
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 59 of 124
Securing Wall Beam
(For 900mm Roofing Containment Set-Up Only)
Fasten (1) M5x10mm screw through the support hanger into the wall beam from the inside of the aisle.
Fasten (3) M6x12mm bolts and (3) M6 nuts to the hanger and wall beam.
Repeat process for every hanger.
Hanger
Support
Hanger
M5x10mm
Screw
M6x12mm
Bolt
M6 Nut
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 60 of 124
Securing Wall Beam
(For 1200mm Vertical Wall Containment Set-Up Only)
Fasten (1) M5x10mm screw through the wall beam bracket into the wall beam from the inside of the aisle.
Fasten (3) M6x12mm bolts and (3) M6 nuts to the hanger and wall beam.
Repeat process for every hanger.
Hanger
Wall Beam
Bracket
M5x10mm
Screw
M6x12mm
Bolt
M6 Nut
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 61 of 124
Securing Wall Beam
(For 1200/1800mm Roofing Containment Set-Up Only)
Fasten (3) M6x12mm bolts and (3) M6 nuts to the hanger and wall beam.
Repeat process for every hanger.
Hanger
M6x12mm
Bolt
M6 Nut
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 62 of 124
Roofing End
Beam
(5) M5x10mm Hex Head Screws (900mm aisle)
(7) M5x10mm Hex Head Screws (1200mm aisle)
(8) M5x10mm Hex Head Screws (1800mm aisle)
Attaching Roofing Beam
(For Roofing Containment Set-Up Only)
Attach the roofing beam to the end of row beam with M5x10mm screws.
Secure the roofing beam to each wall beam with (2) M5x10mm screws.
Repeat process for opposite side of POD.
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 63 of 124
Installing Wall Beam Clamp
Attach the required number of beam clamps to span the length of the aisle with M5x12mm button head
screws.
M5x12mm
Button Head
Screws
Wall Beam
Clamp
Ensure that
flange of Wall
Beam Clamp
faces into aisle
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 64 of 124
Attaching Flap Seal to Wall Beam Clamp
Install the flap seal onto the wall beam clamp for each wall beam as shown.
Wall Beam
Clamp
Flap Seal
Wall Beam
Clamp
Note Flap Seal
Orientation
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 65 of 124
SECTION 3
INSTALLATION OF
AISLE CONTAINMENT ROOFING
CURFS06F03HB**,CURFS06F04HB**,CURFS06F06HB**,
CURFS07F03HB**,CURFS07F04HB**,CURFS07F06HB**,
CURFS08F03HB**,CURFS08F04HB**,CURFS08F06HB**
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 66 of 124
Installing Aisle Containment Roofing Aisle Beam
Position the roofing aisle beam on the (2) wall beams at approximate location(s).
Roofing Aisle
Beam
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 67 of 124
Placing Ceiling Panel
Lower (1) ceiling panel between the roofing end beam and the roofing aisle beam.
Adjust the position of the roofing aisle beam using the ceiling panel as a guide.
Roofing Aisle
Beam
Roofing End
Beam
Ceiling Panel
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 68 of 124
Securing Aisle Containment Roofing Aisle Beam
Attach the roofing aisle beam to the (2) wall beams with (4) M5x10mm hex head screws.
Repeat process for each roofing aisle beam.
Roofing Aisle
Beam
(4) M5x10mm
Hex Head
Screws
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 69 of 124
Securing Ceiling Panel
From underneath the roofing aisle beam, loosen the (4) M5 button head screws.
Slide the (4) M5 button head screws out causing the ceiling panel hold down to slide over the ceiling panel
securing it in place.
Re-tighten the (4) M5 button head screws in the roofing aisle beam.
Repeat process for every roofing aisle beam in pod.
View From Under
Aisle Beam
View From Above Aisle Beam
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 70 of 124
SECTION 4
INSTALLATION OF
AISLE CONTAINMENT VERTICAL WALLS,
VERTICAL WALL ADAPTERS,
AND
VERTICAL WALL BRACE
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 71 of 124
Installing Vertical Wall Brace
The max distance without a vertical wall brace is 2,400mm (8’). NOTE:
Install bracket for vertical wall brace to each wall beam using (2) M5 X 12mm Button Head Screws each as shown.
Install vertical wall brace to both vertical wall brace brackets using (2) M5 X 12mm Button Head Screws on each side
as shown.
Vertical Wall
Aisle Brace
(2) M5x12mm Button
Head Screws
Maximum Distance 2400 mm (8’)
Vertical Wall Aisle Brace
Bracket
(1 on each Wall Beam)
Wall Beam
1
2
(2) M5x12mm Button
Head Screws
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 72 of 124
Installing Vertical Wall Adapter
Using (2) M5x10mm hex head screws, attach the vertical wall adapter to the wall beam.
Repeat process for all of vertical wall adapters required.
Vertical Wall
Adapter
(2) M5x10mm
Hex Head
Screws
Vertical Wall
Adapters
Wall Beam
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 73 of 124
Attaching Wall Brace to Vertical Wall
Using (2) M5x10mm button head screws, attach (2) wall braces to the vertical wall.
Discard the diagonal braces that come with the vertical walls.
Repeat process for all vertical walls required.
(2) M5x10mm
Button Head
Screws
(2) Wall Braces
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 74 of 124
Applying Foam Seal to Vertical Wall
Apply (1) strip of .5"x.75" foam seal across the top flange of the vertical wall.
Repeat process for all vertical walls required.
.5"x.75"
Foam Seal
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 75 of 124
Installing Vertical Wall
Place the vertical wall on top of the vertical wall adapter passing the studs on the adapter through the slots
in the feet of the wall.
Secure the vertical wall to the vertical wall adapter with (4) M5 hex nuts.
Fasten the (2) wall braces to the wall beam with (2) M5x10mm hex head screws.
Repeat process for each vertical wall required.
(4) M5 Hex
Nuts
Vertical Wall Adapter
(2) Wall Braces
(2) M5x10mm
Hex Head Screws
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 76 of 124
Setting Wall Panel Height
Once wall panel is secured to cabinet, raise wall panel to desired height.
Loosely, install the (2) adjustment screws on the front of the wall panel.
Level relative to lower wall.
Tighten adjustment screws to secure wall panel to desired height.
(2) Adjustable
Panel Locking
Screw
Raise Wall Panel to
Desired Height
(Re-tighten adjustment
screws)
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 78 of 124
Attaching Upper Seal
Attach the top seal in between (2) wall panels with (4) M5 nuts.
(4) M5 Nuts
Upper Seal
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 79 of 124
Attaching Foam to Lower Seal
Attach the provided strip of .75W x .5H foam seal to the width of the bottom seal.
.75W x .5H
Foam
Lower Seal
Apply Foam to
this Side of the
Lower Seal.
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 80 of 124
Attaching Lower Seal
Using (4) M5 nuts, attach bottom seal with foam strip in between (2) wall panels.
(4) M5 Nuts
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 81 of 124
SECTION 5
INSTALLATION OF
END OF ROW VERTICAL WALL
C2HACERI1626**, C2HACERI2638**, C2HACERI3866**
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 82 of 124
Attaching Lower Side Frame
Attach lower side frame to the right wall panel with (1) M5 nut.
Repeat process for left side.
Lower Side Frame
M5 Nut
Wall Panel
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 83 of 124
Attaching Lower Cross Beams
Attach lower right cross beam to the bottom of the right wall panel with (2) M5 nuts.
Secure lower right cross beam to the top of the vertical wall adapter.
Repeat process for left side.
NOTE: Lower Right
Cross Beam has a 1
Imprinted on it.
(Left Side has a 2)
NOTE: Push Lower Cross Beams to
Full Outer Position.
(2) M5 Nuts
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 84 of 124
Attaching Upper Cross Beams
Secure the upper right cross beam to the top of the right wall panel with (2) M5 Nuts.
Repeat process for upper left cross beam.
(2) M5 Nuts
Upper Right
Cross Beam
Wall Panel
NOTE: Upper Right
Cross Beam has a 1
Imprinted on it.
(Left Side has a 2)
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 85 of 124
Attach Foam Seal to Upper Side Frame
Attach (1) strip of .5x.25 inch foam next to the inside flange of each of the upper side brackets.
.5"x.25" Foam Seal
Upper Side Frame
Upper Side Frame
.5"x.25" Foam Seal
Top View
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 86 of 124
Attaching Upper Side Frame
Attach (1) upper side frame to the upper right cross beam with (3) M5 12mm screws
Secure upper side frame to lower side frame with (3) M5 12mm screws
Repeat process for left side.
Upper Right
Cross Beam
Upper Side
Frame
Upper Side
Frame
Lower Side
Frame
(3) M5 12mm
Button Head
Screws
(3) M5 12mm
Button Head
Screws
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 87 of 124
Attach Center Cross Beams
Attach (1) center cross beam to upper right cross beam with (2) M5 nuts (do not tighten).
Attach same center cross beam to upper left cross beam with (2) M5 nuts (do not tighten).
Make sure the center cross beam is centered between the upper left cross beam and the upper right cross
beam.
Tighten nuts.
Repeat process for lower right and lower left cross beams.
Center Cross
Beam
Upper Right
Cross Beam
Upper Left
Cross Beam
(2) M5 Nuts
(2) M5 Nuts
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 88 of 124
Attach Center Frames
Attach (1) center frame to the upper center cross beam with (2) M5 nuts.
Repeat process for lower center cross beam.
(2) M5 Nuts
Center
Frame
Center Cross
Beam
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 89 of 124
Assemble H Channel [For End of Row Adjustable Vertical Wall,
38"- 66" (C2HACERI3866) Only]
Using (1) M5x12mm button head torx screws, attach the inside H Channel to the outside H channel.
(1) M5x12mm
Button Head
Torx Screws
Inside
H Channel
Outside
H Channel
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 90 of 124
Attach H Channel to Center Frame [For End of Row Adjustable
Vertical Wall, 38"- 66" (C2HACERI3866) Only]
Attach H channel to the center frame with (2) M5 hex nuts.
(2) M5 Hex
Nuts H Channel
Center Frame
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 91 of 124
Mark and Cut H Channel [For End of Row Adjustable Vertical Wall,
38"- 66" (C2HACERI3866) Only]
Make a mark on the inside and outside H Channels above the threaded studs on the lower center frame and
below the edge of the lower center frame.
Detach H Channel assembly from top center frame.
Separate the inside H Channel from the outside H Channel.
Cut H Channel
Sections Along
Mark from Step 1
Outside
H Channel
Edge of
Lower
Center
Frame
Threaded
Studs on Lower
Center Frame
H Channel
Step 1 Step 2
Inside
H Channel
Mark the H Channel
Above Studs on Lower
Center Frame and
Below the Edge of the
Lower Center Frame.
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 92 of 124
Measure and Cut Wall Panel
Measure distance between top and bottom studs in frame. (Shown as distance "Y")
Measure distance between left and right studs in frame. (Shown as distance "X")
Cut wall panel to match lengths "X" and "Y" using a sharp knife and a straight edge.
Note: For End of Row Adjustable Vertical Wall, 38"- 66" (C2HACERI3866) the combined width of wall
panels and H Channel should total length "X". When trimming length "X", trim the sides equally to keep the
H Channel centered.
"Y"
"X"
Cut Wall Panels to
Match Lengths "X"
and "Y" Using a
Sharp Knife and a
Straight Edge.
H Channel Only Used with End of Row
Adjustable Vertical Wall, 38"- 66"
(Part # C2HACERI3866)
NOTE: When Using H
Channel, Trim Equal
Amounts from Both
Clear Panels to Keep H
Channel Centered.
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 93 of 124
Attaching H Channel to Clear Panels [For End of Row Adjustable
Vertical Wall, 38"- 66" (C2HACERI3866) Only]
Attach the inside H Channel to the outside H Channel with M5x12mm button head torx screws and M5 hex
nuts securing (2) clear panel in between the inside and outside H Channels. The number of screws and nuts
depends on the height of the wall.
NOTE: When placing the clear panels, make sure that they are under the slots in the top of the H Channel.
NOTE: Make Sure
that Clear Panels
Below the Slots in
the H Channel.
Inside
H Channel
Outside
H Channel
M5x12mm But-
ton Head Torx
Screws
M5 Hex Nuts
(2) Clear
Panels
NOTE: Clear
Panels Should
be Below the
Slots in the H
Channel.
NOTE: Cut a Notch in
the Corners of the Clear
Panels for the Nuts that
will Attach H Channel to
Center Frame.
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 94 of 124
Attach Bottom and Side Wall Panel Clamps
Attach required number of panel clamps across the bottom of the wall and along one side with M5 nuts and
M5 16mm hex head screws. (Do not tighten fasteners.)
Note: Required number of panel clamps and fasteners will vary depending on wall size and height.
Panel Clamps
M5 Nuts
M5 16mm Hex
Head Screws
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 95 of 124
Insert Wall Panel
Slide previously cut panel(s) into installed panel clamps to hold them in place.
Note: For End of Row Adjustable Vertical Wall, 38"- 66" (C2HACERI3866) the H Channel will have to be
secured to the center frame with (2) M5 hex nuts.
Panel Clamps
Panel Clamps
Wall Panel
(2) M5 Hex
Nuts
(Only Used with
C2HACERI3866)
NOTE: H Channel Only Used with End of
Row Adjustable Vertical Wall, 38"- 66"
(C2HACERI3866)
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 96 of 124
Attach Top and Remaining Side Wall Panel Clamps
Attach remaining panel clamps across the top of the wall and along the side of wall with M5 nuts and M5
16mm hex head screws to secure wall panel(s) in place.
Tighten all fasteners.
NOTE: Center panel clamps are not used when using the H-Channel [End of Row Adjustable Vertical Wall,
38"- 66" (C2HACERI3866) only].
Panel Clamps
M5 Nuts
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 97 of 124
Foam Seal Installation
Compress and insert (1) strip of foam seal in between the top of the end of row vertical wall and the ceiling
closing any gaps.
Ceiling
Foam
Seal
Top of End of Row
Vertical Wall
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 100 of 124
Flap Seal Installation
Attach a strip of Flap Seal to inner flange of each Vertical Panel so that the bottom is just above the notch on
the panel.
For the 900mm aisle, the flap seal needs to be installed after the vertical panels are put up.Note:
Place This Seal
Just Above
"Notch" on the
Panel
Top View of Left Hand Vertical Panel
900mm/1200mm Aisle
"Notch" on
Vertical
Panel
Top View of Right Hand Vertical Panel
900mm/1200mm Aisle
Top View of Left Hand Vertical Panel
1800mm Aisle
Top View of Right Hand Vertical Panel
1800mm Aisle
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 101 of 124
Attaching Vertical Panel (for 900mm/1200mm Aisles)
Slide the vertical panel over the (2) studs on the transom and the (1) stud on the bottom of the vertical
post.
Fasten in place with (3) M6 nuts.
Repeat process for right side.
Vertical Panel
Transom
(1) M6 Nut
(2) M6 Nuts
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 102 of 124
Attaching Vertical Panel (for 1800mm Aisles Only)
Slide the vertical panel over the (2) studs on the transom and the (2) studs on the bottom of the vertical
post.
Fasten in place with (4) M6 nuts.
Repeat process for right side.
(2) M6 Nuts
Transom
(2) M6 Nuts
Vertical Panel
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 103 of 124
Panel Cover Installation (for 900mm/1200mm Aisles)
Attach (1) Panel Cover to each Vertical Panel with (2) M5 button head screws each.
For the 900mm aisle, these screws also go through the clearance holes in the side panels that were Note:
installed with the end-of-row frame.
(2) Panel Covers
(4) M5 Button
Head Screws
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 104 of 124
Panel Cover Installation (for 1800mm Aisles)
First, place (2) tabs on each panel cover through (2) slots in each vertical panel as shown in Step 1.
Attach (1) Panel Cover to each Vertical Panel with (2) M5 button head screws each as shown in Step 2.
Step 1
(2) M5 Button Head
Screws
(each cover)
Step 2
Tabs
Slots
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 105 of 124
Attaching Door Guides
Attach right hand Door Guide to right hand Vertical Panels with (2) M5 button head screws. (Leave Screws
Loose)
Repeat process for left hand side.
Door Guide
(2) M5 Button
Head Screws
Slots Used to
Adjust Door
Position
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 107 of 124
Right Hand Sliding Door Set-Up
Attach Hook and Bracket to right hand door using (2) M5 hex head screws.
Attach Floor Brush and Floor Brush Clamp to right hand door with (5) M5 button head screws.
(2) M5 Hex
Head Screws
Floor Brush
Floor Brush Clamp (5) M5 Button
Head Screws
Hook
and
Bracket
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 111 of 124
Adjusting Door Seals
Adjust left hand and right hand door side seals to achieve a good seal between the door and the Flap Seal.
Adjust door guides to align bottom of the right hand and left hand doors. Tighten Screws. (Ref. Page 41)
Door Side Seal
Flap Seal
(7) Door Side Seal
Adjustment Screws
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 114 of 124
Header Cover Installation
Slide Header over top of Transom and End Caps.
Slide Pem Studs on inside front of header into holes in End Caps.
Secure Header to End Caps with (4) M5 hex head screws and (2) M5 flange head nuts.
(4) M5 Hex
Head Screws
Header Cover
(2) M5 Flange
Head Nuts
(2) Pem
Studs
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 115 of 124
SECTION 7
INSTALLATION OF BLANKING PANELS
CUFBPR4206HB**, CUFBPR4506HB**, CUFBPR4806HB**,
CUFBPR5206HB**, CUTBPR0610HBN1
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 117 of 124
Placing First Lower Guide
Remove cover off of adhesive strip on the bottom of the lower guide.
Adhere lower guide to the floor with it being against the inside of the frame post and set 2.54mm (.1") into
the aisle from the edge shown below.
Adhesive
Bottom
Adhesive
Cover
Lower
Guide
Inside of
Frame
Post
Lower Guide Set
2.54mm (.1") into
Aisle
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 118 of 124
Additional Lower Guides
Place each additional lower guide end to end to the other side of the POD.
Trim last lower guide to length needed for application
Lower Guide
Trim Last Lower Guide to Length
Needed for Application
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2014
V00029BZ
Page 121 of 124
Sizing Above Cabinet Blanking Panel
Measure from the top of the cabinet up into the gap of the wall beam where the blanking panel will extend
into as show by dimension "Y" in Fig. 1.
Trim the blanking panel to match dimension "Y" as shown in Fig. 2.
Dimension "Y"
Trim Blanking
Panel to Dimension
"Y"
Fig. 1
Fig. 2
Cabinet
This page intentionally left blank.


Produkt Specifikationer

Mærke: Panduit
Kategori: Ikke kategoriseret
Model: Net-Contain

Har du brug for hjælp?

Hvis du har brug for hjælp til Panduit Net-Contain stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Panduit Manualer

Panduit

Panduit MEHT187 Manual

29 December 2024
Panduit

Panduit DIRBB2007S21W Manual

29 December 2024
Panduit

Panduit CDE3 Manual

29 December 2024
Panduit

Panduit EC001 Manual

29 December 2024
Panduit

Panduit PZICE Manual

15 December 2024
Panduit

Panduit PZICEA Manual

15 December 2024
Panduit

Panduit PZNDVK Manual

15 December 2024
Panduit

Panduit DIRLC9606RB1 Manual

11 December 2024
Panduit

Panduit EA001 Manual

9 December 2024
Panduit

Panduit FPONE2 Manual

14 November 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer