Philips EasyKey DV001 Manual

Philips Ikke kategoriseret EasyKey DV001

Læs nedenfor 📖 manual på dansk for Philips EasyKey DV001 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Please read this user manual carefully before using
this product.
Kind reminder:
Host (x1) Magnetic Stand(x1)Sub-unit (x1)
USB cable(x1) Power Adaptor(x1) User Manual(x1) Screw (x6)
Packing List
1
User Manual
Appearance overview
1 Indoor host
Function
button
Indicator ring
Touch panel
MIC
Speaker
Connector
Charging
interface
Reset
2Installation
1Conrm installation position
3
Outside door Inside door
Outside door
6 Host Installation
2
1
5 7 Remove the hostFix sub-unit interface
2
1
4 Magnetic Stand Installation
2
3
1
2
1
2Sub-unit pre-install instruction
3 Fix sub-unit
2 Outdoor sub-unit
Human detection
sensor(Do not block it )
Camera
(Do not block it)
Doorbell
Microphone
Connecting
cable
Sub-unit
interface
Speaker
1
2
User Manual
To register your product(s) and get support from below site:
www.philips.com/support
EasyKey
Smart Door Viewer
DV001
Thank you for purchasing Philips-branded products. For your
safety, please read this user manual carefully before using the
product. Any personal injury, property or other loss caused by not
following the user manual or precautions, no liability will be
assumed by Philips.
This user manual is used as a guide. The photos, pictures, or
illustrations provided in the manual are for explanation purposes,
which may dier from the specic product, please refer to the
actual product. Due to product version upgrade or other needs,
Philips may update this manual timely without advanced
informing. If you need the latest version of the manual, please
download it from the Philips website (www.philips.com/support).
The copyright of any part from this manual, including text,
pictures or illustrations, belongs to Philips. Without written
permission, no corporation or individual may extract, copy,
translate, or modify all or part of this manual in any way. Unless
otherwise agreed, Philips does not make any express or implied
representations and guarantees.
If there is no hole on the door, please drill one with a
diameter of 15 ~ 30mm at the height of 145cm from the
ground.
If there is a hole on the door and installed with a peephole,
please remove the peephole and install the smart door
viewer. The hole diameter range should be 15~50mm.
Please choose the proper screw as per the door thickness
for sub-unit installation.
Short size screw is applicable for a door thickness of
35mm-60mm.
Medium size screw is applicable for a door thickness of
60mm-85mm.
Long size screw is applicable for a door thickness of
85mm-110mm.
Sort out the connecting cable, then tighten the screw
into the sub-unit for 5mm, and tear the foam label
protective sheet on the rear side of the sub-unit.
Adjust the direction of the sub-unit from outside and
make sure the doorbell button is at the bottom. Then
pass the screw and connecting cable through the hole. (If
your door is too thick, use a paper tube to pass the cable
through the door, then remove the paper tube ). Press
hard on the sub-unit to make sure it perfectly adheres to
the door, then remove the lens protective lm.
1
2
Pass the connecting cable of the sub-unit through the
square hole on the magnetic stand from the inside door
( Do not twist or squeeze the connecting cable.).
Attention: Move down
the magnetic stand so
that the screws can be
matched with the
marked position, and
then fasten the screws.
Attention: Insert the
sub-unit interface into
the groove on the
magnetic stand as shown
in the picture.
Hang the magnetic stand on the screws of the sub-unit and
fasten the screws until the magnetic stand can be xed rmly
on the door.
Align the sub-unit interface with the groove on the magnetic
stand, and make sure they are stick to each other rmly.
Gently pull out the connecting cable from the inside
door, and then peel o the protection lm on the back
of the sub-unit interface.
Attention: Align the host
device to the magnetic
stand from the top to
bottom.
Inside door
Tilt the host by 10 degrees and hang it on the steel sheet
from top to bottom. The bottom magnet will automatically
suck with the host. After installation, gently pull the upper
part of the host to check if it is correctly installed.
Outside door
foam label
Inside door
Please hold the bottom of the host with both hands and
tilt it upwards by 10 degrees, and then move it against the
steel sheet to remove the host.
Philips and the Philips Shield Emblem are registered trademarks
of Koninklijke Philips N.V. and are used under license. This product
has been manufactured by and is sold under the responsibility of
Shenzhen Conex Intelligent Technology Co., Ltd. and Shenzhen
Conex Intelligent Technology Co., Ltd. is the warrantor concerning
this product.
Version: 1.0


Produkt Specifikationer

Mærke: Philips
Kategori: Ikke kategoriseret
Model: EasyKey DV001

Har du brug for hjælp?

Hvis du har brug for hjælp til Philips EasyKey DV001 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Philips Manualer

Philips

Philips TAB5009 Manual

13 November 2024
Philips

Philips Avent SCF763 Manual

13 November 2024
Philips

Philips SCD293 Manual

3 Oktober 2024
Philips

Philips SPD2413BM Manual

29 September 2024
Philips

Philips CP0281 Manual

29 September 2024
Philips

Philips DL8770 Manual

29 September 2024
Philips

Philips s-bag FC8021 Manual

28 September 2024
Philips

Philips TAFBL1 Manual

25 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kramer

Kramer VP-8X8 Manual

25 November 2024
Kramer

Kramer PT-2C Manual

25 November 2024
Lazer

Lazer Bob+ Manual

25 November 2024
Dometic

Dometic DPS 80 Manual

25 November 2024
Kramer

Kramer 102MX Manual

25 November 2024
Kramer

Kramer FC-18 Manual

25 November 2024
Kramer

Kramer DSP-62-UC Manual

25 November 2024
Tiger

Tiger SKF-H101 Manual

25 November 2024