Philips OneBlade QP1424 Manual

Philips barbermaskine OneBlade QP1424

Læs nedenfor 📖 manual på dansk for Philips OneBlade QP1424 (2 sider) i kategorien barbermaskine. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
QP QP161424, 24
5 mm
13/64in
3 mm
1/8in
1 mm
3/64in
Manufactured for: Philips Personal Health
a division of Philips North America LLC
P.O. Box 10313, Stamford, CT 06904, USA
This symbol on the product’s nameplate means
it is listed by Underwriters’ Laboratories, Inc.
Norelco is a registered trademark of Philips North America LLC.
PHILIPS and Philips shield are registered trademarks of
Koninklijke Philips N.V.
©2023 Philips North America LLC. All rights reserved.
3000.102.5217.2 (04/24/2023)
2
1
1
2
3
6
14
22
2
10
18
1
7
15
23
3
11
19
8
16
24
4
12
20
9
17
5
13
21
English
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric product, basic precautions should
always be followed, including the following:
Read all instructions before using this product.
DANGER
To reduce the risk of electric shock:
-To charge the product, only use a USB power source on
a certied product with output rating 5V, ≥ 1A. For safe
charging in a moist environment (e.g. in a bathroom),
only use an IPX4 (splash-proof) power source. A
suitable power source (e.g. Philips HQ87) is available via
www.philips.com/support. If you need support nding
the correct USB power source, contact Philips support at
1-800-243-3050. Using a non-certied USB power source
may cause hazards or serious injuries.
-Keep the USB cable and the USB power source dry (Fig. 2).
-Do not reach for a corded product that has fallen into
water. Unplug immediately from the power outlet.
-Do not place or store the product where it can fall or be
pulled into a tub or sink. Do not place or drop the product
into water or other liquid.
-This product does not work while it is connected to the
power outlet. Except when charging, always unplug this
product from the power outlet.
-Remove USB power source from power outlet and product
before cleaning the product with water.
WARNING
To reduce the risk of burns, re, electric shock, or injury to
persons:
-This product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the product by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the product.
-Use this product only for its intended household use as
described in this manual. Misuse can lead to hazards or
serious injuries. Do not use attachments not recommended
by Philips North America LLC.
-Never operate this product if it has a damaged USB power
source, if it is not working properly, after it has been
dropped or damaged, or after the product or the USB
power source has been dropped into water. For assistance
call 1-800-243-3050.
-Keep the USB cable and the USB power source away from
heated surfaces.
-Never drop or insert any object into any opening.
-Do not use the USB power source in or near a power outlet
that contains an electric air freshener to prevent damage to
the USB power source.
-Do not use product outdoors or operate where aerosol
(spray) products are being used or where oxygen is being
administered.
-Always check cutting units and other attachments and
accessories before you use the product. Never use the
product with a damaged cutting unit, attachment or
accessory, as injury may occur.
-Always attach the USB cable to the USB power source and
the product rst, then attach the USB power source to the
power outlet. To disconnect, set all controls to 'o' position.
Then remove the USB power source from the power outlet.
-Plug USB power source directly into power outlet. Do not
use an extension cord.
-Unplug USB power source before plugging in or
unplugging the product.
-The batteries used in this product may present a re or
chemical burn hazard if mistreated. Do not disassemble,
heat above 100°C (212°F) or incinerate.
-Only use original Philips accessories or consumables.
-Charge, use and store the product at a temperature
between 41 °F / 5°C and 95 °F / 35°C.
-Keep product and batteries away from re and do not
expose them to direct sunlight or high temperatures.
-If the product becomes abnormally hot or smelly, changes
color or if charging takes longer than usual, stop using and
charging the product and contact Philips.
-Do not place products and their batteries in microwave
ovens or on induction cookers.
-Do not open, modify, pierce, damage or dismantle the
product or battery to prevent batteries from heating up
or releasing toxic or hazardous substances. Do not short-
circuit, overcharge or reverse charge batteries.
-If batteries are damaged or leaking, avoid contact with the
skin or eyes. If this occurs, immediately rinse well with water
and seek medical care.
-When you handle batteries, make sure that your hands, the
product and the batteries are dry.
-To avoid accidental short-circuiting of batteries after
removal, do not let battery terminals come into contact
with metal objects (e.g. coins, hairpins, rings). Do not wrap
batteries in aluminum foil. Tape battery terminals or put
batteries in a plastic bag before you discard them.
SAVE THESE
INSTRUCTIONS
Introduction
Congratulations on your purchase and welcome to Philips
Norelco!
To fully benet from the support that Philips Norelco oers,
register your product at .www.philips.com/register
General description (Fig. 1)
Your product comes with the following components included:
1 Protection cap
2 Blade
3 OneBlade handle
4 Beard guard 3/64in (1mm)
5 Beard guard 1/8in (3mm)
6 Beard guard 13/64in (5mm)
7 USB charging cable
Note: Philips IPX4 (splash-proof) USB power adapters are
available for purchase separately.
The following additional accessories are included with the
QP1624 only:
1 Body guard
2 Skin guard
3 Body blade
Getting started
-Use this product for its intended household use as
described in this manual.
-For hygienic reasons, the product should only be used by
one person.
Charging OneBlade
Low Battery
When the battery is low, the motor will run more slowly.
Charging with the USB charging cable
1 Insert the small plug into the OneBlade handle, then insert
the USB plug into a USB power adapter. Plug the adapter
into a 120V AC outlet (Fig. 3).
2 To fully charge the battery, allow it to charge for 8 hours.
The charging indicator will remain illuminated when the
product is connected to the mains.
3 Unplug the adapter from the power source, then remove
the charging cable from the handle.
Note: for safety reasons, the product can only be used when
the charging cable is not attached.
4 A fully charged OneBlade has an operating time of at least
30 minutes.
Turning OneBlade on and o
To turn the product on or o, simply press the power button
once (Fig. 4).
Tip: If the product does not turn on, check that the battery is
fully charged and remove the charging cable from the handle
before pressing the power button. If the product still does not
turn on, check that the blade is clean and undamaged.
Using OneBlade
Facial Hair
Shaving and edging
To shave with OneBlade, remove any combs or guards. Your
OneBlade is waterproof, so you can shave in the shower or
with foam or gel.
1 To shave, make long, slow and steady strokes (Fig. 5),
applying gentle pressure with the blade at against your
skin (Fig. 6). Move the blade back and forth to make use of
both sides of the blade.
2 To edge or contour your beard (Fig. 7), mustache or
sideburns, make short strokes with the blade held
perpendicular to your skin (Fig. 8). Alternatively, make small
strokes with the blade at against your skin.
3 For best results, clean your OneBlade after each use.
Trimming
To trim facial hair, use the 13/64in. (1mm), 1/8in. (3mm) or
3/16in. (5mm) click-on guard provided. The numbers on the
guards relate to the hair length remaining after trimming (in
millimeters).
Tip: if you are unsure which length you prefer, start with
the longest guard available and reduce the length further if
necessary.
1 Hook the back of the guard (the side with the number on
it) under the bottom of the blade, then gently press on the
front of the guard until it clicks into place (Fig. 9).
2 Trim against the direction of hair growth (Fig. 10), with the
teeth of the guard at against your skin (Fig. 11).
3 To detach the guard, hold the handle rmly and gently lift
the guard o the blade (Fig. 12).
4 For best results, clean your OneBlade after each use.
Body Hair
Shaving body hair
Note: For hygiene reasons, we recommend using the separate
body blade provided when trimming body hair.
Use your OneBlade with the body blade attached to shave hair
anywhere below the neck.
Areas including your chest, stomach and legs can be shaved
using the bare blade, in the same way as shaving your face.
Note: to minimize the risk of cuts always use the skin guard
when trimming sensitive areas. This includes when shaving
your armpits or groin (including scrotum).
1 If you are using the skin guard, place it onto the blade and
gently press until it clicks into place (Fig. 13).
2 Switch on your OneBlade, and place the blade at against
your skin.
3 Make long, steady strokes, exerting gentle pressure and
allowing the blade to glide across the surface of your skin
(Fig. 14).
Tip: on certain areas, using the ngers of your free hand to
spread the skin and hold it taut will provide better results.
4 The blade and skin guard are double sided. Move the blade
back and forth to catch hairs growing in dierent directions.
5 Clean your OneBlade after each use. If you used the skin
guard, press your thumb onto the exposed at surface of
the blade (Fig. 15), and use your ngers to gently pull o
the skin guard before cleaning.
Trimming body hair
The 1/8inch (3mm) body guard allows you to trim hair on
your body below the neckline (for example chest, armpits and
groin).
For hygiene reasons, we recommend using the separate body
blade provided when trimming body hair.
Note: For delicate areas such as the groin, only trim when the
guard is attached.
1 Place the the guard onto the blade and gently press until it
clicks into place (Fig. 16).
2 Trim against the direction of hair growth, with the teeth of
the guard at against your skin. The guard is double sided,
so you can move your OneBlade back and forth to cut hairs
growing in dierent directions (Fig. 17).
3 To detach the guard, hold the handle rmly and gently
lift the guard o the blade. For best results, clean your
OneBlade after each use.
Maintenance
Cleaning OneBlade
Clean after each use
For a quick clean, simply blow on the blade and any
accessories to remove hairs and dirt (Fig. 18).
Thorough cleaning
1 Turn on your OneBlade and rinse it under the tap with cold
or lukewarm water (Fig. 19). If you shave with foam or gel,
be sure to remove all residue after each shave.
2 Guards can also be cleaned under the tap using warm
water.
3 Allow your OneBlade and accessories to air dry completely
before storage.
Note: Do not bang the handle on the sink or any hard surface,
a this may damage the product (Fig. 20). Do not use a towel or
cloth to dry the blade.
Storage
Store your OneBlade in a safe, dry location where it will not be
crushed, banged, or subject to damage. To protect the blade,
store the product with the protection cap attached. Do not
wrap the cable around the product when storing, and do not
place or store the product where it can fall or be pulled into a
tub or sink, water or other liquid while plugged in.
Blade Replacement
When to replace the blade
We recommend replacing the blade of your OneBlade at least
once every four months, or whenever the blade shows signs of
wear.
Wear indicator
A replacement symbol will gradually appear on the blade as
you use it. When the replacement symbol is fully visible, it's
time to replace your blade (Fig. 21).
Note that accessories such as guards can prevent the
replacement symbol from becoming visible.
Tip: the replacement symbol resembles the arrow icon on the
handle of your OneBlade. For older blades, a green rectangle
may appear in place of the replacement symbol.
If blade is damaged
If you notice any damage on your blade, please replace it
immediately.
How to replace the blade
Before you begin, make sure your OneBlade is turned o and
any guards are removed.
1 Gently pull o the old blade, holding it by both short sides
(Fig. 22).
2 The old blade can be discarded with your normal household
waste.
3 Remove your replacement blade from the packaging. To
avoid damaging the blade, don't use sharp objects or crush
the packaging.
4 Hold the new blade by both short sides and insert the
protrusions on the bottom of the blade into the slots on the
OneBlade handle (Fig. 23).
5 Gently press the blade downwards onto the handle until it
clicks into place.
6 Your OneBlade is now ready to use.
The following Philips Norelco replacement blade packs are
available for your OneBlade:
-QP1424: QP210/80, QP220/80, QP230/80 and QP250/80.
-QP1624: QP610/80 and QP620/80.
Assistance
For assistance, visit our website: www.philips.com/support
or call toll free 1-800-243-3050.
Disposal
-This product contains a rechargeable nickel metal hydride
battery which must be disposed of properly (Fig. 24).
-The built-in battery should not be disposed of with normal
household waste
-Contact your local town or city ocials for battery disposal
information. You can also call 1-800-822-8837 or visit
www.call2recycle.org for battery drop-o locations.
-For assistance, visit our website www.philips.com/support
or call 1-800-243-3050 toll free.
-Your product is designed and manufactured with
high quality materials and components, which can be
recycled and reused. For recycling information, please
contact your local waste management facilities or visit
www.recycle.philips.com
Full Two-Year Warranty
Philips North America LLC warrants this new product (except
blade) against defects in materials or workmanship for a
period of two years from the date of purchase, and agrees to
repair or replace any defective product without charge.
IMPORTANT: This warranty does not cover damage resulting
from accident, misuse or abuse, lack of reasonable care, the
axing of any attachment not provided with the product or
loss of parts or subjecting the product to any but the specied
voltage or batteries.*
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to
www.philips.com/support. It is suggested that for your
protection you return shipments of product by insured mail,
insurance prepaid. Damage occurring during shipment is not
covered by this warranty.
NOTE: No other warranty, written or oral, is authorized by
Philips North America LLC.
This warranty gives you specic legal rights, and you may
also have other rights which vary from state to state. Some
states do not allow the exclusion or limitation of incidental or
consequential damages, so the above exclusion and limitations
may not apply to you.
*Read enclosed instructions carefully.
45-DAY MONEY-BACK GUARANTEE
If you are not fully satised with your product send the
product back and we’ll refund you the full purchase price.
The product must be shipped prepaid by insured mail,
insurance prepaid, have the original sales receipt,
indicating purchase price and date of purchase.
We cannot be responsible for lost mail.
The product must be postmarked no later than 45 days
after the date of purchase. Philips reserves the right to
verify the purchase price of the product and limit refunds
not to exceed suggested retail price.
To obtain the money-back guarantee service, please go to
www.PhilipsMoneyBack.com and follow the simple 3-step
process.
Delivery of refund check will occur 6–8 weeks after receipt of
returned product.


Produkt Specifikationer

Mærke: Philips
Kategori: barbermaskine
Model: OneBlade QP1424

Har du brug for hjælp?

Hvis du har brug for hjælp til Philips OneBlade QP1424 stil et spørgsmål nedenfor, og andre brugere vil svare dig




barbermaskine Philips Manualer

barbermaskine Manualer

Nyeste barbermaskine Manualer