Philips SQM7842 Manual


Læs nedenfor 📖 manual på dansk for Philips SQM7842 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Engli s h
1 Important safety instructions
Caution
Read these instructions before you begin. If you are unsure of any
part of the process, contact a professional contractor or installer
for assistance. Improper installation can result in injury or damage.
The wall or mounting surface must be capable of supporting
the combined weight of the mount and the display; if not, the
structure must be reinforced.
Locate pipes, wires, or any other hazards in the wall where you
wish to install the mount before drilling.
Safety gear and proper tools must be used. Failure to do so can
result in injury or damage.
Two people are recommended for installation. Do not attempt to
lift a heavy display without assistance.
Follow all instructions and recommendations regarding adequate
ventilation and suitable locations for mounting your display.
Consult the owner‘s manual for your particular display for more
information.
This wall mount is intended for use only with the maximum
weight of 45 kg (100 lbs). Use with heavier than the maximum
weights indicated may result in instability causing possible injury.
2 Tilt wall mount (for LCD, Plasma, and LED displays)
What's in the box
Wall plate (x1)
Mount arm (x2)
User manual (x1)
Hardware kit (x1)
Hardward kit
A
M8 x 63 lag bolt (x4)
B
Lag bolt washer (x4)
C
Concrete anchor (x4)
D
M6 x 12 screw (x4)
E
M6 x 30 screw (x4)
F
M8 x 12 screw (x4)
G
M8 x 30 screw (x4)
H
M6 washer (x4)
I
M8 washer (x4)
J
Spacer (x8)
Tools required
Phillips head screw driver
Ratchet or driver with 13 mm (1/2”) socket
Electric or portable drill
6 mm (1/4”) drill bit and stud nder for drywall installation
10 mm (3/8”) Masonry bit for concrete installation
3 Installation
Mount to the drywall
Caution
For safety reasons, this mount must be secured to at least two
wood studs no less than 16” apart. The studs must be capable of
supporting the combined weight of the mount and display.
1 Use a high quality stud nder to locate two adjacent
studs where you wish to install your mount. Mark both
edges of each stud to help identify the exact center.
Note
You must use the center of each stud to avoid cracking or splitting
the wood during installation.
2 Place the wall plate against the wall and level it using the
integrated bubble level.
3 While another person holds the wall plate in position,
mark four locations (two per stud) for securing the
mount to the wall (see Fig. 1).
4 Set the wall plate aside and drill a 6 mm (1/4”) pilot hole
at each marked location.
5 Place the wall plate back against the wall and attach it
using the lag bolts
A
and lag bolt washers
B
provided
(see Fig. 2). Do not over-tighten these bolts and do not
release the wall plate until all bolts are in place. Ensure
that the wall plate remains level after all bolts are secured.
Mount to the concrete wall
Caution
For safety reasons, the concrete wall must be capable of
supporting the combined weight of the mount and the display. The
manufacturer takes no responsibility for failure caused by walls of
insufcient strength.
1 Place the wall plate against the wall in the desired
location and level it using the integrated bubble level.
2 While another person holds the wall plate in place, mark
four evenly spaced locations on the wall for securing the
mount (see Fig. 3).
3 Set the wall plate aside and drill a 10 mm (3/8”) hole at
each marked location. Remove any excess dust from the
holes.
4 Insert a concrete anchor
C
into each hole so that it is
ush with the concrete surface (see Fig. 4). A hammer can
be used to lightly tap the anchors into place if necessary.
A
B
C
D
E
F
G
H
I
J
**
1 2
3
4
5
6
7
8 9
2015 © Gibson Innovations Limited.
All rights reserved.
This product has been manufactured by, and is sold
under the responsibility of Gibson Innovations Ltd., and
Gibson Innovations Ltd. is the warrantor in relation to
this product.
Philips and the Philips Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used
under license from Koninklijke Philips N.V.
UM_SQM7842
27_EN_V1.0
WK15314
SQM7842
Register your product and get support at
www.philips.com/support
User manual
Manual del usuario
sqm7842_27_2L_um_150730.indd 1-3 30/07/2015 18:00:58


Produkt Specifikationer

Mærke: Philips
Kategori: Ikke kategoriseret
Model: SQM7842

Har du brug for hjælp?

Hvis du har brug for hjælp til Philips SQM7842 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Philips Manualer

Philips

Philips TAB5009 Manual

13 November 2024
Philips

Philips Avent SCF763 Manual

13 November 2024
Philips

Philips SCD293 Manual

3 Oktober 2024
Philips

Philips SPD2413BM Manual

29 September 2024
Philips

Philips CP0281 Manual

29 September 2024
Philips

Philips DL8770 Manual

29 September 2024
Philips

Philips s-bag FC8021 Manual

28 September 2024
Philips

Philips TAFBL1 Manual

25 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kramer

Kramer VP-8X8 Manual

25 November 2024
Kramer

Kramer PT-2C Manual

25 November 2024
Lazer

Lazer Bob+ Manual

25 November 2024
Dometic

Dometic DPS 80 Manual

25 November 2024
Kramer

Kramer 102MX Manual

25 November 2024
Kramer

Kramer FC-18 Manual

25 November 2024
Kramer

Kramer DSP-62-UC Manual

25 November 2024
Tiger

Tiger SKF-H101 Manual

25 November 2024