Quoizel Blaze PCBZ1620C Manual

Quoizel Lettelse Blaze PCBZ1620C

Læs nedenfor 📖 manual på dansk for Quoizel Blaze PCBZ1620C (2 sider) i kategorien Lettelse. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
1of2
Assembly Instruction Sheet #IS-PCBZ1620C
For Style PCBZ1620C
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
Package Contents
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
2018 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
A
ReleasedDate:2018-03-13
CFixture Body
x 1
Crossbar
Assembly
x 1
Please go to for product cleaning tips. Go to the selection.
LED 29W
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
www.quoizel.com Care + Maintenance
Light Source:
Estimated Assembly Time:
Preparation:
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
STEP 1 -Install the Crossbar Assembly to Outlet Box and Adjust
the length of the Nipple
A. Attach the Crossbar Assembly (A) to the Outlet Box with the head of
the Green Ground Screw facing you. Secure it with Outlet Box
Screws (not included), tighten until snug
B. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
C. Place the Fixture Body (C) over the nipple against the ceiling to
determine the correct position of the nipple. Thread the Knob (B)
onto the nipple. Adjust the nipple to allow the Fixture Body (C) to rest
against the ceiling when held in place by the Knob (B).
D. Remove the Knob (B) and the Fixture Body (C). Tighten the lock
washer and the hex nut against the crossbar to secure in place.
.
Outlet Box Screw
(not included)
Hex Nut and
Lock Washer
Outlet Box
Green Ground Screw
Figure 1
Nipple
DPanel
x 1
BKnob
x 1
A
B
C
STEP 2 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 2
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
STEP 3 Install Fixture Body-
A. Carefully tuck all wires into the outlet box and position the Fixture
Body (C) over the outlet box. Attach the Fixture Body (C) over the
nipple and secure with the Knob (B). Hand tighten until snug.
C
Outlet Box
Figure 3
Nipple
B


Produkt Specifikationer

Mærke: Quoizel
Kategori: Lettelse
Model: Blaze PCBZ1620C

Har du brug for hjælp?

Hvis du har brug for hjælp til Quoizel Blaze PCBZ1620C stil et spørgsmål nedenfor, og andre brugere vil svare dig




Lettelse Quoizel Manualer

Lettelse Manualer

Nyeste Lettelse Manualer