Radial Engineering ProMS2 Manual

Radial Engineering Splitter ProMS2

Læs nedenfor 📖 manual på dansk for Radial Engineering ProMS2 (2 sider) i kategorien Splitter. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

www.radialeng.com

True to the Music

Radial Engineering Ltd.

®True to the Music

USER GUIDE

Radial Engineering Ltd. ProMS2® Microphone Splitter ProMS2® Microphone Splitter

FEATURES

1. -30dB PAD: Allows balanced +4dB

line-level sources to connect to the

ProMS2 input.

2. Mic input: Used to connect a low

impedance, balanced, microphone or

direct box.

3. Direct-1 thru: A parallel direct

output used to bridge the mic or DI to

the primary mixing console.

4. Bookend design: 14 gauge steel

outer shell creates protective zone

around connectors and switches.

5. Full-bottom no-slip pad: This

provides electrical isolation and

plenty of ‘stay-put’ friction to keep the

ProMS2 in one place.

6. Direct-2 output: Equipped with

ground lift. Used to bridge the signal

to an additional audio device.

7. Lift (Direct-2): Disconnects

pin-1 (ground) on the direct-2 XLR

output to help reduce hum and buzz

caused by ground loops.

8. Isolated output: Transformer-

isolated to eliminate ground loop hum

and buzz. Used to bridge the balanced

mic signal to a second audio system.

9. Lift (Isolated output): Disconnects

pin-1 (ground) on the isolated XLR

output to help further reduce hum and

buzz caused by ground loops.

10. Stee l I -b e a m : E n c l os u r e

eliminates stress that could torque

the PC board.

11. Military-grade PCB: Double-

sided PCB with plated through-holes

is bolted to welded steel standoffs.

12. Eclipse: High performance mic

bridging transformer offers outstanding

a u d i o p erforma nc e . F e a t u r e s

mu-metal shield for protection against

stray electromagnetic ﬁ elds.

96 7 8

1 52 3 4

10 1211

RADIAL ENGINEERING 3 YEAR TRANSFERABLE LIMITED WARRANTY

RADIAL ENGINEERING LTD. (“Radial”) warrants this product to be free from defects in material and

workmanship and will remedy any such defects free of charge according to the terms of this warranty.

Radial will repair or replace (at its option) any defective component(s) of this product (excluding ﬁ nish and

wear and tear on components under normal use) for a period of three (3) years from the original date of

purchase. In the event that a particular product is no longer available, Radial reserves the right to replace

the product with a similar product of equal or greater value. In the unlikely event that a defect is uncovered,

please call 604-942-1001 or email service@radialeng.com to obtain an RA number (Return Authorization

number) before the 3 year warranty period expires. The product must be returned prepaid in the original

shipping container (or equivalent) to Radial or to an authorized Radial repair center and you must assume

the risk of loss or damage. A copy of the original invoice showing date of purchase and the dealer name

must accompany any request for work to be performed under this limited and transferable warranty. This

warranty shall not apply if the product has been damaged due to abuse, misuse, misapplication, accident

or as a result of service or modiﬁ cation by any other than an authorized Radial repair center.

THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE FACE HEREOF AND

DESCRIBED ABOVE. NO WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT

LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE SHALL EXTEND BEYOND THE RESPECTIVE WARRANTY PERIOD DESCRIBED ABOVE OF

THREE YEARS. RADIAL SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY SPECIAL, INCIDENTAL

OR CONSEQUENTIAL DAMAGES OR LOSS ARISING FROM THE USE OF THIS PRODUCT. THIS WAR-

RANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH

MAY VARY DEPENDING ON WHERE YOU LIVE AND WHERE THE PRODUCT WAS PURCHASED.

Speciﬁ cations and appearance are subject to change without notice.

Radial Engineering Ltd.

1588 Kebet Way, Port Coquitlam BC V3C 5M5

tel: 604-942-1001 • fax: 604-942-1010

info@radialeng.com • www.radialeng.com

Audio circuit type: Passive mic splitter, transformer based

Number of channels: Three-way splitter (one in/three out)

Frequency response: 20Hz ~ 20KHz

Dynamic range: 140dB

Maximum input: +25dBu @ 1kHz

Harmonic distortion: 0.005% @ 1kHz

Phase deviation: 1° @ 100Hz; 4° @ 20Hz

CMRR: 114dB @ 60Hz

Input impedance: 150 Ohms, balanced

Output impedance: 150 Ohms, balanced

XLR output: AES standard pin-1 Ground, pin-2 (+), pin-3 (-)

Ground lift: Lifts pin-1 on the XLR output

ProMS2 SPECIFICATIONS

Produkt Specifikationer

Mærke:	Radial Engineering
Kategori:	Splitter
Model:	ProMS2

Har du brug for hjælp?

Hvis du har brug for hjælp til Radial Engineering ProMS2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Splitter Radial Engineering Manualer

Radial Engineering ProMS2 Manual

19 December 2024

Radial Engineering HotShot DM1 Manual

19 December 2024

Splitter Manualer

Nyeste Splitter Manualer

Digitus DS-46304 Manual

13 December 2024

Smart-AVI DVS4P Manual

9 December 2024

Smart-AVI DVS-8P Manual

9 December 2024

Smart-AVI DVS-400 Manual

9 December 2024

Audio-Technica AT-SL914HD Manual

6 December 2024

Audio-Technica ATW-SC410 Manual

6 December 2024

Digitus DS-55339 Manual

2 December 2024

Palmer PMB-L Manual

19 November 2024

Palmer PLS-02 Manual

12 November 2024

Tripp Lite B155-004-HD-V2 Manual

7 Oktober 2024