RCA RP5430 Manual

RCA Clockradio RP5430

Læs nedenfor 📖 manual på dansk for RCA RP5430 (1 sider) i kategorien Clockradio. Denne guide var nyttig for 14 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

2. To check the remaining duration before

the radio turns off, press and hold SLEEP.

3. To cancel the sleep function, press

SNOOZE or OFF.

Setting Clock

1. Slide the switch /WAKE1/WAKE2/

on the top of the unit to clock position.

2. Press REV FWD or to set the clock

time. The time decrements or increments

will follow by a faster rate when you press

and hold the buttons. The “:” between

hour and minute time flashes when you

are setting the time. AM or PM icon will

also beside the time.

3. Slide the switch /WAKE1/WAKE2/

on the top of the unit to position

when finished.

Before You Begin General Controls Clock

Important InformationFCC Information Safety Information

English

Radio

It is important to read this instruction book prior to using your new product for the first time.

RP5430

u s e r

m a n u a l

WARNING:

TO PREVENT FIRE OR ELECTRICAL

SHOCK HAZARD,DO NOT EXPOSE THIS PRODUCT

TO RAIN OR MOISTURE.

SEE MARKING ON BOTTOM / BACK OF PRODUCT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

T HE E XC LA M AT IO N

P OIN T WIT HIN T HE

T R I A N G L E I S A

WAR NI NG SIG N

AL E R T ING YO U OF

I M P O R T A N T

I N S T R U C T I O N S

A C C O M P A N Y I N G

T H E P R O D U C T.

T H E L I G H T N I N G

FLASH AND ARROW-

HEA D WIT HIN T HE

T R I A N G L E I S A

W A R N IN G S I G N

ALERT ING YOU OF

" D A N G E R O U S

V OLT A G E" IN SI DE

THE PRODUCT.

CA UT I ON: T O R ED UC E T H E

RISK O F E LE CT RI C S HOC K,

D O N O T R E M O V E C O V E R

( O R B A C K ) . N O U S E R -

S E RV I CE A B L E PA R T S IN -

S ID E . R E F E R S E R V I C IN G

T O Q U A L I F I E D S E RV I C E

P E R SO N NE L .

Setting Wake Time

This unit allows two wake times to be set.

1. Slide the switch /WAKE1/WAKE2/

on the top of the unit to orWAKE 1

WAKE 2 position.

2. Press REV or FWD to set the

respective wake time. The time

decrements or increments will follow

by a faster rate when you press and

hold the buttons. The “:” between

hour and minute time flashes when

you are setting the time.

3. Slide the switch /WAKE1/WAKE2/

on the top of the unit to position

when finished.

Selecting Wake Source

You may be woken up by radio or alarm.

1. Select an AM or FM station (see

directions on “Radio”).

2. Set a wake time (see above direction).

3. Press W 1AKE - OFF or 2

repeatedly on the top of the unit to

select a waking mode. Corresponding

icon lights on the front of the unit.

1- Wake 1 by alarm

1- Wake 1 by radio

2- Wake 2 by alarm

2- Wake 2 by radio

Checking Wake Time

Slide the switch /WAKE1/WAKE2/

on the top of the unit to orWAKE 1

WAKE 2 position to check the currently

set wake time.

EN/F/E

FCC Information

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference

that may cause undesired operation.

In accordance with FCC requirements, changes

or modifications not expressly approved by

Thomson Inc. could void the user’s authority to

operate this product.

This device generates and uses radio frequency

(RF) energy, and if not installed and used

properly, this equipment may cause interference

to radio and television reception.

If this equipment does cause interference to

radio or television reception (which you can

determine by unplugging the unit), try to correct

the interference by one or more of the following

measures:

• Re-orient the receiving antenna (that is, the

antenna for the radio or television that is

“receiving” the interference).

• Move the unit away from the equipment that

is receiving interference.

• Plug the unit into a different wall outlet so

that the unit and the equipment receiving

interference are on different branch circuits.

If these measures do not eliminate the

interference, please consult your dealer or an

experienced radio/television technician for

additional suggestions. Also, the Federal

Communications Commission has prepared a

helpful booklet, “How To Identify and Resolve

Radio TV Interference Problems.” This booklet

is available from the U.S. Government Printing

Office, Washington, DC 20402. Please specify

stock number 004-000-00345-4 when ordering

copies.

EXPORTER

Thomson Inc.

P. O. Box 1976

Indianapolis, IN 46206 - 1976

Trademark(s) ® Registered

Marque(s) ® Deposée(s)

Marca(s) ® Registrada(s)

www.rca.com

Printed in China / Impreso en China

5629 7940 (EN/F/E)

IMPORTADOR

Comercializadora Thomson de México, S.A. de C.V.

Álvaro Obregón No. 151. Piso 13.

Col. Roma. Delegación Cuauhtémoc

C.P. 06700. México, D.F.

Telefono: 52-55-11-020360

RFC: CTM-980723-KS5

For Your Safety

The AC power plug is polarized

(one blade is wider than the

other) and only fits into AC

power outlets one way. If the

plug will not go into the outlet

completely, turn the plug over

and try to insert it the other

way. If it still does not fit, contact a qualified

electrician to change the outlet, or use a

different one. Do not attempt to bypass this

safety feature.

Caution: The screw fastening power cord at the

bottom enclosure is served as a means of power

cord strain relief. Do not loosen or throw this

screw away!

For Your Records

In the event that service should be required, you

may need the model number. In the space

below, record the date and place of purchase:

Date of Purchase:

Place of Purchase:

Service Information

This product should be serviced only by those

specially trained in appropriate servicing

techniques. For instructions on how to obtain

service, refer to the warranty included in this

Guide.

Technical Information

Product: Clock Radio

Brand: RCA

Model: RP5430

Electrical Consumption

Power Supply: 120V ~ 60Hz

Power Consumption: 4 Watts

IMPORTER

Comercializadora Thomson de México, S.A. de C.V.

Álvaro Obregón No. 151. Piso 13.

Col. Roma. Delegación Cuauhtémoc

C.P. 06700. México, D.F.

Telefono: 52-55-11-020360

RFC: CTM-980723-KS5

The descriptions and characteristics in this owner’s manual are for the purpose of general reference only and not

as a guarantee. In order to provide you with the highest quality product, we may make changes or modifications

without prior notice. The English version serves as the final reference on all product and operational details

should any discrepancies arise in other languages.

• Make sure that you keep your set

away from water and high

temperatures.

• Do not use your System immediately

after transporting it from a cold place

to a warm place, as condensation may

cause the system to malfunction.

• Keep your unit away from humid

areas and abnormally hot places.

• To prevent personal injury, do not

reverse any batteries.

• The use of apparatus in moderate

climates.

• The apparatus shall not be exposed to

dripping or splashing and that no

objects filled with liquids, such as

vases, shall be placed on the

apparatus.

• No naked flame sources, such as

lighted candles, should be placed on

the apparatus.

• Attention should be drawn to the

environmental aspects of battery

disposal.

• Minimum distances (2cm) around the

apparatus for sufficient ventilations.

• The ventilation should not be

impeded by covering the ventilation

opening with items, such as

newspaper, table-cloths, curtains, etc.

• The rating plate is located at the

bottom cabinet of apparatus.

Ecology

Help protect the environment - we

recommend that you dispose of used

batteries by putting them into specially

designed receptacles.

Maintenance

Clean the unit with a soft cloth, or a damp

chamois leather. Never use solvents.

Power Failure Indicator

When AC power is interrupted (disconnected)

for a short period of time, both time and

alarm settings will change (unless batteries

are installed). After AC power is restored

(reconnected), the Digital Display will blink to

indicate that power was interrupted and you

should readjust the time and alarm settings.

Plugging In For Power

AC OUTLET POWER SUPPLY:

120V~60Hz

Note:Note:

Note:

Power is fed to the unit even

when it is not functioning. To cut

the power supply off, the power cable

must be unplugged.

Top View

OFF - turns the unit on or off.

FWD - sets time (increases value).

SNOOZE - enters snooze mode where the

alarm will quiet but sound again once the

snooze period is over.

REV - sets time (decreases value).

RADIO/AUX - selects radio or AUX mode.

WAKE - OFF - activates and sets wake

function.

/WAKE1/WAKE2/ - slide switch to set

Wake 1, Wake 2 and clock time.

NAP - activates nap function.

SLEEP - activates sleep function.

Back View

AUTO DIMMER - turns auto dimmer function

on or off.

TIME ZONE - slide to select time zone

corresponds to your location.

DST - turns daylight saving function on or off.

AM/FM - selects between AM and FM bands.

Right View

-VOLUME+ - adjusts volume.

TUNING - selects radio frequencies.

AUX IN - AUX input jack.

Before You Plug for Power

1. Setting Time Zone

You may slide the TIME ZONE selector at

the back of the unit to Eastern (EST),

Central (CST), Mountain (MST) or Pacific

(PST) (refer to the maps on the right).

2. Daylight Saving

You can slide the DST switch at the back

of the unit to turn on/ off in areas

observing/ not observing such time

change.

WARNING: Please avoid playing with

these buttons after entering the

Clock/Alarm set mode.

Auto Clock Set

You do not have to set the clock time as a

built-in automatic time set system is

equipped in this clock powered by 3V (2

X AA batteries, included). All you have to

do is to plug this clock for power and

current time will be shown automatically.

However, the batteries can also be

exhausted and we recommend that you

replace the batteries every 2-3 years.

Auto Brightness Control

Clock time and radio frequency are

display on the display area at the front of

the unit. The display brightness can be

adjusted automatically by analyzing the

intensity of surrounding light sources.

Slide AUTO DIMMER on the back of the

unit to position to activate theON

function.

Selecting Radio Mode

Press RADIO/AUX to switch on radio.

Switching Band

Slide the switch on the back of theAM/FM

unit to select FM or AM band.

Tuning the Radio

Turn the knob on the right of theTUNING

unit to adjust radio frequency. Radio

frequency shows on the display.

Built-In AFC

The Built In Automatic Frequency Control

(AFC) works only on FM. It helps reducing

drift on FM reception and keeping the

radio locked in on the FM station to which

it is tuned.

When tuning in FM stations, you may

notice that the station you are tuning can

be well-tuned on two or three nearby

points on the dial. Always tune carefully

at the loudest and clearest point.

AM Antenna

A built-in ferrite rod antenna eliminates the

need for an outside antenna for AM

reception. Rotating the unit slightly may

improve reception of distant AM stations.

Listening to Auxiliary Source

1. Connect your auxiliary source (e.g. mp3

player) to the AUX input jack on the right

side of the unit.

2. Turn on the unit and your auxiliary source.

3. Press RADIO/AUX to switch to listen to

auxiliary source. The AUX indicator on the

front will turn on. Press again to switch

back to listen to the radio.

Wake Function

Tip: The unit equips with GRAD-GRAD-GRAD-GRAD-GRAD-

U-WAKE U-WAKE U-WAKE U-WAKE U-WAKE feature, the alarm tone

volume will increase gradually to

its maximum in about 30 to 45

seconds.

Turning Off the Wake Alarm or

Radio

Press on the top of the unit. TheSNOOZE

wake alarm or radio will be switched off

temporarily. The alarm or radio will be on

again when the snooze period is over. (see

“SmartSnoozeTM Operation”)

To turn off the wake alarm or radio

completely, press . The wake alarm orOFF

radio will activate again the next day unless

you switch off the Wake function (see

“Switching off Wake Function”).

SmartSnooze

Operation

This operation allows extra sleep time

after the wake function is on. The alarm

will be off by pressing SNOOZE NAP, ,

SLEEP REV , or FWD until the snooze

period is over. Snooze function can be

used repeatedly up to 30 minutes (default:

9 minutes). After this, the wake function

will turn off until the next day.

Set the “quiet” period as follow:

1. Press and hold SNOOZE.

2. Press REV or FWD to set the

quiet period. The time decrements or

increments will follow by a faster rate

when you press and hold the buttons.

Switching Off Wake Function

Press W 1AKE - OFF or 2 repeatedly on

the top of the unit until no wake mode icon

shows on the display.

Sleep Function

In sleep mode, you can set the duration

(up to 2 hours) before the radio turn off

automatically.

1. Press and hold on the top of theSLEEP

unit and use or toREV FWD

set the duration up to 2 hours. The

time decrements or increments will

follow by a faster rate when you press

and hold the buttons.

Note: The radio will be switched on.

Nap Function

This function wakes you up after a short

period of time (from 10 minutes to 2

hours).

1. Press and hold on the top of theNAP

unit and use or toREV FWD

set the duration up to 2 hours (each

press decreases or increases duration

by 10 minutes). The time decrements

or increments will follow by a faster

rate when you press and hold the

buttons.

2. The clock time shows after a few

seconds if no button is pressed. NAP

icon shows on the display to indicate

the function is activated.

3. To check remaining nap time, press NAP

once to show the time on the display

briefly.

4. When the alarm sounds, press toSNOOZE

switch it off.

• To cancel the function before the nap

time ends, press and hold until noNAP

nap icon shows on the display.

Clock

US Time Zones

Canadian Time Zones

PST MS T CST EST

Wake Function

(CST)

(MST)

(PST)

(EST)

(CST)

(MST)(PST) (EST)

Battery Back-Up Operation

This clock radio is equipped with a

memory holding system that can be

powered with 2 “AA” batteries (included).

The power failure protection circuit will

not operate unless battery is installed.

When normal household power is

interrupted, or AC line cord is unplugged,

the batteries will power the clock radio to

keep track of time and alarm settings

programmed into memory. When the

battery backup functions, the digital

display will not light, however, the

function of alarm still occurs during the

power interruption if remaining battery

power is adequate. Normal operation will

resume after AC power is restored so you

will not have to reset the time or the

alarm.

Install battery as follow:

1. Remove battery compartment door

(located at the bottom of the radio)

by applying thumb pressure to the

tab on battery door and then lift the

door out and off the cabinet.

2. Insert 2 AA batteries (included).

3. Replace the compartment door.

Note: we recommend that you replace the

batteries every 2-3 years.

Es importante leer este manual antes de usar por vez primera su euipo.

Note: SmartSnoozeTM is only

available when /WAKE1/ /WAKE1/ /WAKE1/ /WAKE1/ /WAKE1/

WAKE2/WAKE2/WAKE2/WAKE2/WAKE2/ is at the lock

position.

Produkt Specifikationer

Mærke:	RCA
Kategori:	Clockradio
Model:	RP5430

Har du brug for hjælp?

Hvis du har brug for hjælp til RCA RP5430 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Clockradio RCA Manualer

30 September 2024

23 August 2023

15 Maj 2023

11 Marts 2023

26 Oktober 2022

Clockradio Manualer

Nyeste Clockradio Manualer

ADE CK 1706 Manual

15 November 2024

Numan Mini One Manual

3 November 2024

Insignia NS-ALCL24 Manual

15 Oktober 2024

JVC RA-E314B Manual

10 Oktober 2024

Grundig Sonoclock 50L Manual

7 Oktober 2024

SilverCrest SCUR 3 A1 Manual

7 Oktober 2024

Denver CRL-340 Manual

4 Oktober 2024

Roadstar CLR-450R Manual

4 Oktober 2024

Caliber HCG 011DAB Manual

4 Oktober 2024

La Crosse Technology 617-2916 Manual

4 Oktober 2024