RCA RTD317W Manual

RCA Hjemmebiograf sæt RTD317W

Læs nedenfor 📖 manual på dansk for RCA RTD317W (4 sider) i kategorien Hjemmebiograf sæt. Denne guide var nyttig for 31 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

USER MANUAL

RTD317W

It's important to read this instruction prior to using your new product for the rst time.

This device complie s with part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmf ul inte rference in a residential

installation. This equipment ge nerate s, uses

and can radiate radio frequency energy and, if

not installed and used in accordance with the

instructions, may cause harmful interference to

radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful inter ference

to radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

•

I nc re a s e th e se pa r at i on be t we e n t he

•

equipment and receiver.

Connect the equipment into an outlet on a

•

circuit dierent from that to which the receiver

is connected.

Consult the dealer or an experienced radio /

•

TV technician for help.

WARNING: Changes or modications to this unit

not expressly approved by the party responsible

for compliance could void the user's authority to

operate the equipment.

FCC Information

Connections and Setup

Overview of Controls - Front Panel Controls

Overview of Controls Overview of Controls Playing Discs - Basic Functions Basic Playback Operations

Connections and Setup Connections and Setup

FCC Information Important Information

Important Safety Instructions

This Home Theater has earned

the ENERGY STAR.

This product complies with DHHS Rules 21

CFR Subchapter J. Applicable at the date of

manufacture.

Ventilation

You must adequately ventilate the product. Make

sure there is adequate space around the unit

to provide proper air ow for ventilation. See

diagram.

For your safety

The AC power plug is polarized

(one blade is wider than the

other) and only ts into AC

power outlets one way. If the

plug won’t go into the outlet

completely, turn the plug over

and try to insert it the other way.

If it still won’t t, contact a qualied electrician to

change the outlet, or use a dierent one. Do not

attempt to bypass this safety feature.

Removing the power plug is the only way to

completely remove power from your product. Make

sure the power plug remains easily accessible.

Note

This DVD player is designed and manufactured to

respond to the Region Management Information.

If the Region number of a DVD disc does not

correspond to the Region number of this DVD

player, this player cannot play the disc. The Region

number for this DVD player is Region 1.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSER-

VICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN

THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE

SAME OR EQUIVALENT TYPE.

WARNING: MAINS PLUG IS USED AS DISCONNECT DEVICE AND IT SHOULD REMAIN READILY OPERABLE

DURING INTENDED USE. IN ORDER TO DISCONNECT THE APPARATUS FROM MAINS COMPLETELY, THE

MAINS PLUG SHOULD BE DISCONNECTED FROM THE MAINS SOCKET OUTLET COMPLETELY.

Caution

This product utilizes a laser. Use of controls or

adjustments or performance of procedures other

than those specified may result in hazardous

radiation exposure. Do not open covers and do

not repair yourself. Refer servicing to qualified

persionnel.

Visible and invisible laser radiation when open

and interlocks defeated.

DO NOT STARE INTO BEAM.

Class 1 laser product

DVD copy protection

In accordance with the DVD standard, your DVD

player is equipped with a Copy Protection system,

which can be switched on and o by the DVD

disc itself, in order to make any recording of the

relevant DVD disc onto a videotape of very poor

picture quality, or even impossible. This product

incorporates copyright protection technology

that is protected by method claims of certain U.S.

patents and other intellectual property rights

owned by Macrovision Corporation and other

rights owners. Use of this copyright protection

technology must be authorized by Macrovision

Corporation, and is intended for home use only

unless otherwise authorized by Macrovision

Corporation. Reverse engineering or disassembly

is prohibited.

Important battery information

• Do not mix dierent types of batteries or new

and old batteries. Do not use rechargeable

batteries.

• In order to avoid any risk of explosion, observe

the polarities indicated inside the battery

compartment. Replace only with the type of

batteries specied. Do not dispose of them in

a re or recharge them.

• If you are not using the remote control for a

long period of time, remove the batteries.

Illustrations contained in this document are for

representation only.

Please respect the environment and

prevailing regulations. Before you

dispose of batteries or accumulators,

ask your dealer whether they are

subject to special recycling and if

they will accept them for disposal.

T chis lass B digital apparatus ompliesc

with CES-003.Canadian I

Cet appareil num rique de la lassc B

est onforme lac norme du NMB-003

du Canada.

Please read and save for future reference.

Some of the following information may not apply

to your particular product; however, as with any

electronic product, precautions should be observed

during handling and use.

Read these instructions.

•

Keep these instructions.

•

Heed all warnings.

•

Follow all instructions.

•

Do not use this apparatus near water.

•

Clean only with a dry cloth.

•

Do not block any ventilation openings. Install in

•

accordance with the manufacturer’s instructions.

Do not install near any heat sources such

•

as radiators, heat registers, stoves, or other

apparatus (Including amplifiers) that produce

heat.

Do not defeat the safety purpose of the polarized

•

or grounding-type plug. A polarized plug has

two blades with one wider than the other. A

grounding type plug has two blades and a third

grounding prong. The wide blade or the third

prong is provided for your safety. If the provided

plug does not fit into your wall outlet, consult

an electrician for replacement of the obsolete

outlet.

Protect the power cord from being walked on

•

or pinched particularly at plugs, convenience

receptacles, and the point where they exit from

the apparatus.

Only use attachments / accessories specied by

•

the manufacturer.

Use only with a cart, stand, tripod,

•

bracket, or table specied by the

manufacturer, or sold with the

apparatus. When a cart is used,

use caution when moving the

cart / apparatus combination to

avoid injury from tip-over.

Unplug this apparatus during lightning storms

•

or when unused for long periods of time.

Ref e r all se rv ic i ng to qu ali f i ed ser vi c e

•

personnel. Servicing is required when the

apparatus has been damaged in any way, such

as the power cord or plug is damaged, liquid

has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or

has been dropped.

]

Portable Cart

Warning

Important Safety Instructions

Additional safety information

• Apparatus shall not be exposed to dripping or

splashing and no objects lled with liquids, such as

vases, shall be placed on the apparatus.

• Always leave sucient space around the product for

ventilation. Do not place product in or on a bed, rug,

in a bookcase or cabinet that may prevent air ow

through vent openings.

• Do not place lighted candles, cigarettes, cigars, etc.

on the product.

• Connect power cord only to AC power source as

marked on the product.

• Care should be taken so that objects do not fall into

the product.

• Do not attempt to disassemble the cabinet. This

product does not contain customer serviceable

components.

If your product operates on batteries, adhere to the

following precautions:

A. Any battery may leak electrolyte if mixed with a

dierent battery type, if inserted incorrectly, or if all

batteries are not replaced at the same time.

B. Any battery may leak electrolyte or explode if disposed

of in re or an attempt is made to charge a battery

not intended to be recharged.

C. Discard leaky batteries immediately. Leaking batteries

can cause skin burns or other personal injury. When

discarding batteries, be sure to dispose of them in the

proper manner, according to your state/provincial and

local regulations.

D. Battery shall not be exposed to excessive heat such

as sunshine, re or the like.

Connecting the antennas

The AM and FM antennas connect to the AM and

FM terminals on the system’s back panel. They must

be hooked up in order to receive clear reception.

   

       



 



AM Loop Antenna

1. Uncoil the AM Antenna wire.

2. Press down on the Antennas tab to open the

terminal.

3. Make sure the white wire on the AM loop antenna

is inserted into the AM loop terminal and the other

wire is inserted into the ground loop terminal.

FM75

White

Antenna

GND

Connecting to your TV (VIDEO)

Method 2

Component video jacks (Pr, Pb, Y)

• The component video jacks are color-coded

green, blue and red.

• Additional component video cables (not

supplied) are required to provide best picture

quality. They are usually color-coded green, blue

and red.

• Connect the component video OUT jacks on the

receiver to the component video IN jacks on your

TV so the video content goes from the receiver

to the screen.

Method 1

Composite video jack (yellow)

• The basic video jack is color-coded yellow.

• Video cable (yellow) is supplied for the connection

for good picture quality.

• Connect the video OUT jack on the receiver to

the Video IN jack on your TV so the video content

goes from the receiver to the screen.

• If your television is a high denition

television, use the unit’s progressive

scan output to get the highest possible video

resolution. Set the Progressive Scan option

in the Video menu to On.

• If one of the devices is not working, check that

all the cables have been inserted properly

into the jacks.

• Connecting mono components to your

receiver: If your component has only one

output for audio (mono), connect it to the

white audio jack on the receiver and don’t

use the cable’s red plugs.

Connecting to your TV (via HDMI input)

HDMI stands for High Denition Multimedia

Interface. HDMI transfers digital audio and

uncompressed digital video on a single cable.

Press the HDMI button on the remote control to

change output signals as follows: 480p, 720p,1080i

and 1080p.

Note: Refer to the owner’s manual of the connected

TV as well.

Getting sound from external sources

such as TV

Using AUDIO IN jack

Connect the Ø3.5mm AUDIO IN jack on the front

panel of the unit to the headphone output on mp3

players.

Using AUX IN jacks

1. Connect the AUX IN jacks from the unit to the

AUDIO OUT jacks on VCR, TV, Set Top Box or

other component.

2. Push the AUDIO/AUX button on the remote

control to activate the sound from the external

source.

3. Push the SURROUND button on the remote

control to select the sound mode.

Digital optical input

1. Connect components capable of outputting

Dolby Digital (e.g. TV or Set Top Box) or standard

PCM (CD) format digital signals.

2. Push the OPTICAL button on the remote control

to activate the sound from the external source.

3. Push the SURROUND button on the remote

control to select the sound mode.

Notes

• Ø3.5mm to Ø3.5mm audio cable s (not

included).

• Press either SOURCE on the main unit or AUDIO

/AUX on the remote control to select AUDIO IN

mode.

• Press the SURROUND button on the remote

control to select the sound mode.

• Suggest using Ø3.5mm AUDIO

IN jack for MP3 player and AUX

IN jacks for auxiliary equipment

such as DVD, VCR or PC.

• If the AUX IN (or AUDIO IN) audio signal

is mono, you may not receive audio on

all speakers.

Connecting the speakers

Speaker wires are color-coded to match the terminals. Connect the speaker wire from the back of each speaker to

the corresponding color terminal at the back of the unit. Press down the tab to open the terminal and insert the

wire. Release the tab to lock wire in the terminal.

• When connecting the speakers, make sure the polarities (“+” speaker wire to “+” on the receiver. For example, red

wire to red terminal on the receiver) of speaker wires and terminals match. If the cords are reversed, the sound

will be distorted. Do not let the speaker wires touch each other, it will damage the Home Theater’s amplier.

• Center speaker provided with this unit are magnetically shielded to protect your TV set. It is not recommended

to place the front speakers, surround speakers and subwoofer near the TV set.

To adjust each speaker volume level for optimum listening experience.

(1) Press the LEVEL button on the remote control to select FL (front Left speaker).

(2) Press the VOL+/VOL- buttons to adjust the value up or down (between -10dB and +10dB).

(3) Repeat step (1) and (2) for the other speakers FR, SL, SR, CT, SW.

Speaker gains may be set to levels of up to +10dB, actual max levels may also depend on your Volume Setting.

Note:

Insert 2 “AAA”(“UM-4”/”R03”) batteries

to the remote control prior to use.

1. Left, Right (Front Speakers)

Front speakers carry primarily music and sound

eects.

2. Center

In surround mode, the center speaker carries most

of the dialog as well as music and eects.

It should be set between the left and right peakers.

3. Surround (Rear Speakers)

The surround speakers’ overall sound balance

should be as close as possible to the front peakers.

Proper placement is vital to establish an evenly

distributed sound eld.

4. Subwoofer

A subwoofer is designed to reproduce powerful low

bass eects (explosions, the rumble of spaceships,

etc.).



Front speaker placement

For best results, follow the speaker placement

below.

Alignment

Align the center speaker evenly with (A) or slightly

behind (B) (the left and right speakers), but not

ahead of them.

Angle

Place the left and right speakers to form a 45-

degree angle with your favorite viewing position

to duplicate the soundtrack mixer’s perspective.

Height

The three front speakers should be as close as

possible to the same height. This often requires

placing the center speaker directly on top (A) or

beneath (B) the TV set.

Positioning speakers

Accessories provided

















 





Things to consider before you connect

• Ensure that the mains supply in your house

complies with that indicated on the identication

sticker located on the back of your unit.

• Install your unit horizontally, away from

any source of heat (replace) or appliances

creating strong magnetic or electric elds. The

components of this unit are sensitive to heat.

The maximum ambient temperature should not

exceed 35°C / 95°F.

• Leave enough space around the unit to allow

adequate ventilation: 10 cm/4 inches on either

side and above the top, and 5 cm/2 inches at the

rear.

• The humidity of the room should not exceed 75%.

If you have to use the unit outdoors, do not expose

it to rain or splashing water. The apparatus should

not be exposed to dripping or splashing and no

objects lled with liquids, such as vases, should

be placed on the apparatus.

• Moving the unit from a cold place to a warm one

can cause condensation on some components

inside the unit. Let the condensation disappear

on its own before turning the unit on again.

• Before moving the unit, make sure the disc tray

is empty.

Better surround placement

Location

If possible, place surround speakers to either side

of the listening area, not behind it.

Height

If space permits, install surround speakers 2-3 feet

above viewers. This helps to minimize localization

eects.

Alternative Surround Placement

Rear wall

If rear wall mounting is the only choice, aim the

speakers at each other (A), towards the front (B) or

towards the sidewalls (C, D).

Experiment with placement until sounds seem to

surround you, rather than come from behind you.

No adjacent walls

Surround speakers can go on stands facing each

other to approximate sidewall mounting (A), or to

the sides or rear of the viewing area, aimed upwards;

they can go right on the oor, or preferably, a few

feet o the oor such as on end tables (B).

Test tone/Channel balance

Channel balance

Your receiver is equipped with a test signal

generator for balancing the channels. As the signal

“travels” from channel to channel, adjust the level

controls until each channel plays at the same

loudness level.

Level adjustment and surround channel level

expectation

Even though you adjust the surround channel

to be as loud as the others on the test signal, on

actual program material the surround channel is

adjust the surround level; program producers use

surround for subtle atmospherics and ambience,

and only rarely for special eects.

ON•OFF: Turns on/o the unit.

DVD: Selects the DVD mode.

TUNER: Selects the TUNER and selects between FM/

AM.

AUDIO/AUX: Selects and toggles between the front

AUDIO IN AUX IN mode and rear mode. (for

listening to audio input from connected TV,

VCR or SetTop BOX).

OPTICAL: Selects OPTICAL IN at rear for digital audio

connection.

0-9 : Number entry.

CLEAR: Quits the current setting manually from the

TV screen without saving change.

INFO: Accesses the Info menu.

TITLE: Accesses the title menu of DVD discs.

DISC MENU: Accesses the disc menu during playback.

OK : Conrms your selection.

/ / / : To navigate through the menus. The left and

right arrows also tune the radio frequency in

the tuner mode.

MUTE: Mutes and restores the sound.

SETUP: Enters Setup menu.

RETURN: In DVD mode, returns to the previous menu.

VOL +/- : Adjusts the sound volume.

CH+/ , CH–/ : Directly accesses the next or previous

chapter (DVD) or track (CD). Selects

programmed stations in TUNER mode.

REV: Starts reverse accelerated play.

PLAY: Starts playing a disc.

FWD: Starts forward accelerated play.

SLOW: Selects SLOW motion function.

STOP : Stops playback.

PAUSE: Freezes frame, accesses frame advance.

AUDIO: Accesses the audio function.

ANGLE: Accesses the camera angle function for DVD

disc.

ZOOM: Accesses the Zoom function.

SUBTITLE: Selects the subtitle languages or turns

subtitle o ( if available).

HDMI: Changes video output signals (480p, 720p,

1080i or1080p).

SUBWOOFER : Selects among subwoofer output levels

(soft/balance/strong/powerful).

RANDOM:

Turns on/o random playback on CDDA disc.

REPEAT: Accesses the repeat function.

LEVEL: Toggles channels for dierent level settings.

Adjusts the value using VOL +/-.

SURROUND: Changes the Surround sound

setting.

Press the button to select between

5.1 Channel and Stereo modes.

Remote control functions in tuner mode

TUNER: Selects the TUNER and switch between

FM/AM.

VOL+/–: Adjusts the sound volume.

MUTE: Mutes and restores the sound.

TUNER +/–: Tunes down and up the radio

frequencies.

MEMORY: Stores a station.

CH+/–: Selects programmed stations.

AUDIO: Selects between Stereo and Mono

mode for Tuner (FM).

Compatible discs

•DVD,DVD-R,DVD-RW,DVD+R,DVD+RW

•CD,CD-R,CD-RW

Compatible formats

•DVD,JPEG

•CD,VCD

Regional coding

Your unit has been designed to process regional

management information stored on DVD discs. The

regional code for your unit is 1. Discs that have a

dierent regional code will not play.

Operating the DVD receiver

1. Turn on your television set.

2. Press ON OFF on the remote or ON/STANDBY 

located on the unit’s front panel. Press DVD on

the remote control.

Loading disc

1. Press on the front panel to open the disc tray.

2. Place a disc onto the disc tray with the label side

up.

3. Press again to close the disc tray.

Playback

Switch the unit and the TV set on.

1. After loading a disc, playback starts

automatically, or the disc menu appears. If the

disc menu appears, select the Play option to

begin playback.

2. Press STOP to stop playback.

Accelerated play

While the disc is playing, press REV or FWD one

or more times to vary the speed and direction of

the accelerated play. Press PLAY to resume normal

playback.

Pause

While the disc is playing, press PAUSE once for freeze

frame. Press PLAY to resume normal playback.

Frame advance

1. Press PAUSE twice. “Step” is displayed.

2. Each time you press PAUSE button, the picture

advances one frame.

3. Press PLAY to resume normal playback.

Variable slow motion

1. Press SLOW button on the remote in play

mode.

2. Each time the SLOW button is pressed the

speed of slow-motion playback changes in the

following sequence:

3. Press PLAY to resume normal playback.

Changing chapter/track

While the disc is playing, press the CH+/- button

to go immediately to the next or previous chapter,

or to the next or previous track.

Zoom

1. While a disc is playing, press ZOOM until you

reach the zoom size you want. The ZOOM

button toggles through 2x, 3x, 4x and then

zooms out to 1/2x, 1/3x and 1/4x, then returns

to normal playback.

2. Move from one area to another (pan) using the

arrow buttons.

3. To turn ZOOM o, press ZOOM until you get to

the ZOOM OFF option.

Types of menus

• Discmenu—Theappearanceandcontentsof

this menu varies according to the type of disc

you have inserted. It is separate from the Setup

menu.

• Infomenu—Theunit’sInfomenu appearsat

the top of the screen while the disc is playing.

Press INFO on the remote to switch the Info

menu on or o.

• Setup menu — Press SETUP to access  this

menu.

SF 1/ 2 SF 1/ 3 SF 1/ 4 SF 1/ 5

PLAY SF 1/ 7 SF 1/ 6

T T

7 cm

10 cm10 cm

10 cm

Selects the input sources. Press

repeatedly to select:

•DVD–towatchDVDvideos.

•TUNER–tolistentotheradio.

•AUXIN(rear)/AUDIOIN(front)

- to listen to the audio input

from the connected TV, VCR or

Set Top Box.

•OPTICAL(rear)-toconnect

digital audio components.

Toggles between dierent

subwoofer output levels (among

soft/balance/strong/powerful).

Starts/pauses

playing a disc. Adjusts the

volume.

Switches the

unit on and

o.

AUDIO IN jack -

connects audio

devices.

Opens and closes

the disc tray.

Stops disc

playback.





 







S



   Ω Ω Ω Ω









Insert

Press

Release









Service information

This product should be serviced only by those

specially trained in appropriate servicing

techniques.

THE LIGHTNING FLASH AND ARROWHEAD WITHIN

THE TRIANGLE IS A WARNING SIGN ALERTING YOU

OF “DANGEROUS VOLTAGE” INSIDE THE PRODUCT.

THE EXCLAMATION POINT WITHIN THE TRIANGLE

IS A WARNING SIGN ALERTING YOU OF IMPORTANT

INSTRUCTIONS ACCOMPANYING THE PRODUCT.

WARNING

To reduce the risk of re or electric shock

hazard, do not expose this product to rain or

moisture. The apparatus shall not be exposed

to dripping or splashing and that no objects

lled with liquids, such as vases, should be

placed on the apparatus.

- 1 -

- 4 -

- 8 - - 9 - - 10 - - 11 -

- 5 - - 6 - - 7 -

- 2 - - 3 -

Using remote control to navigate through

the on-screen menus

Use and OK on the remote control to , , ,

navigate through the on-screen displays (the

DVD player’s menu, the Info Display that appears

during playback, or a disc’s menu).

Use on the remote to move through on-, , ,

screen menus in the direction of the arrow button

(e.g., to move right, press ). The arrow buttons are

used to highlight an option. Once highlighted,

press OK to select the option that is highlighted.

Aiming

Aim surround speakers straight across the room,

not down at viewers, to help create a more open,

spacious surround sound eld.

Rear of the unit

Rear of the unit Rear of the unit

Green

Blue

Red

To H DMI

input

HD MI c able

( snot upplied)

Produkt Specifikationer

Mærke:	RCA
Kategori:	Hjemmebiograf sæt
Model:	RTD317W

Har du brug for hjælp?

Hvis du har brug for hjælp til RCA RTD317W stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Hjemmebiograf sæt RCA Manualer

19 Juli 2024

9 Juli 2024

21 Juli 2023

1 November 2022

23 Oktober 2022

Hjemmebiograf sæt Manualer

Nyeste Hjemmebiograf sæt Manualer

LG HB45E Manual

14 December 2024

Boston Acoustics TVee One Manual

13 December 2024

Pure Acoustics RB 6 Manual

8 December 2024

Pure Acoustics Noble II Manual

8 December 2024

Pure Acoustics Super Nova 8 Manual

8 December 2024

Sony SA-PSD5 Manual

14 Oktober 2024

Onkyo HT-S9800 Manual

13 Oktober 2024

Panasonic SC-HT40 Manual

12 Oktober 2024

LG MAI0702 Manual

7 Oktober 2024

LG MAI0182 Manual

7 Oktober 2024