Roland BNC-05BK2 Manual

Roland Ikke kategoriseret BNC-05BK2

Læs nedenfor 📖 manual på dansk for Roland BNC-05BK2 (3 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 26 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/3

Check the Included Items

Before you begin assembling the stand, check that all the items

were supplied.

Symbol Name Quantity

ABench seat 1

BLegs 4

CHex bolts *1 4

DWashers *1 4

ESpring washers *1 4

FWrench *2 1

*1: Attached to the legs.

*2: Attached to the bench seat.

* To prevent injury, work gloves should be worn while

performing the assembly.

* When removing the wrench from the bottom of the seat, pay

attention to the tip of the holder.

Assembly

1. Place the bench seat (A) upside down in a stable

location.

* When placing the bench seat upside down, take care to

protect the seating surface from damage. Handle it with care

so that it does not fall or overturn.

2. Attach the legs (B).

Place a spring washer (E) and a washer (D) on each hex bolt (C),

and provisionally tighten each leg (B). At this time, tighten the

hex bolts (C) by hand.

* Place the spring washer (E) and washer (D) on

the hex bolt (C) in that order.

* Note the position of the screw holes in the legs

(B) and the holes in the metal  xtures of the

bench seat (A).

3. Place the bench in the location in which you are going

to use it, and tighten the legs (B).

While applying pressure on the seat, go around and tighten each

hex bolt (C) little by little, while adjusting the position of the legs

as necessary to prevent any wobbling. In other words, tighten

the hex bolt for each leg gradually, a little each time, as you go

around in order starting with leg number 1, then moving to

number 2, then number 3, then number 4; after which you can

go back to number 1 and repeat the process.

* If the height of the bench is adjustable, be careful not to

insert your hand into the metal components of the height

adjustment mechanism.

If the bench wobbles after you’ve fastened all the legs,  rst

loosen the hex bolt for leg number 1. Then, while applying

pressure to the center of the seat, retighten the hex bolt.

If necessary, repeat this process for the other legs until the

wobbling is eliminated.

4. Finally, tighten the hex bolts (C) further, and verify that

none of them are loose.

* Use the included wrench (F) to  rmly tighten the hex bolts

the washers (D).

Completed bench

* In the interest of product improvement, the speci cations

and/or appearance of this product are subject to change

without prior notice.

Maintenance

At regular intervals, please check that the hex bolts are  rmly

tightened and that the legs are stable. If any hex bolts are loose,

retighten them.

If you notice any other abnormality, immediately stop using the

bench, and contact your dealer for service.

Musical Instrument Bench Owner’s Manual

Before using this product, carefully read the sections entitled: ”USING THE UNIT SAFELY” and ”IMPORTANT NOTES.” These sections provide important informa-

tion concerning the proper operation of this product. Additionally, the Owner’s manual should be saved and kept on hand as a convenient reference.

USING THE UNIT SAFELY IMPORTANT NOTES

Used for instructions intended to alert the

user to the risk of injury or material

damage should the unit be used

improperly.

* Material damage refers to damage or

other adverse effects caused with

respect to the home and all its

furnishings, as well to domestic animals

or pets.

Used for instructions intended to alert the

user to the risk of death or severe injury

should the unit be used improperly.

The symbol alerts the user to things that must be

carried out. The specific thing that must be done is

indicated by the design contained within the circle. In the

case of the symbol at left, it means that the power-cord

plug must be unplugged from the outlet.

The symbol alerts the user to important instructions or

warnings.The specific meaning of the symbol is

determined by the design contained within the triangle. In

the case of the symbol at left, it is used for general

cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never be

carried out (are forbidden). The specific thing that must

not be done is indicated by the design contained within

the circle. In the case of the symbol at left, it means that

the unit must never be disassembled.

About WARNING and CAUTION Notices About the Symbols

ALWAYS OBSERVE THE FOLLOWING

WARNING

Do not disassemble or modify by yourself

Do not carry out anything unless you

are instructed to do so in the owner’s

manual. Otherwise, you risk causing

malfunction.

Do not repair or replace parts by yourself

Refer all servicing to your retailer, the

nearest Roland Service Center, or an

authorized Roland distributor, as listed

on the “Information.”

Do not use or store in the following types of

locations

• Subject to temperature extremes (e.g.,

direct sunlight in an enclosed vehicle,

near a heating duct, on top of heat-

generating equipment); or are

• Damp (e.g., baths, washrooms, on wet

 oors); or are

• Exposed to steam or smoke; or are

• Subject to salt exposure; or are

• Exposed to rain; or are

• Dusty or sandy; or are

• Subject to high levels of vibration and shakiness.

Do not place in an unstable location

Otherwise, you risk injury as the result of

this product toppling over or dropping

down.

Be cautious to protect children from injury

Always make sure that an adult is

on hand to provide supervision and

guidance when using this product in

places where children are present, or

when a child will be using this product.

Do not drop or subject to strong impact

Otherwise, you risk causing damage or

malfunction.

CAUTION

Take care so as not to get  ngers pinched

When handling the following moving

parts, take care so as not to get  ngers,

toes, etc., pinched. Whenever a child uses

this product, an adult should be on hand

to provide supervision and guidance.

• Height adjustment handle

Precautions concerning use of bench

When using the bench, please observe

the following points:

• Do not use the bench as a toy, or as a

stepping stool.

• Do not allow two or more persons to

sit on the bench.

• Do not adjust the height while sitting

on the bench.

• Do not sit on the bench if the bolts holding

the bench legs are loose. (If the bolts are loose,

immediately re-tighten them using the supplied

tool.)

• Never insert your hand into the gap (the metal

height adjustment mechanism) under the seat

lid. Doing so may cause your hand to be pinched

or injured.

Keep small items out of the reach of children

To prevent accidental ingestion of the

parts listed below, always keep them out

of the reach of small children.

• Included Parts

• Washers

• Spring washers

Placement

• Do not expose this product to direct sunlight,

place it near devices that radiate heat, leave it

inside an enclosed vehicle, or otherwise subject

it to temperature extremes. Also, do not allow

lighting devices that normally are used while

their light source is very close to this product

(such as a piano light), or powerful spotlights

to shine upon the same area of this product for

extended periods of time. Excessive heat can

deform or discolor this product.

• Do not allow rubber, vinyl, or similar materials to

remain on this product for long periods of time.

Such objects can deform or discolor this product.

• Do not paste stickers, decals, or the like to this

product. Peeling such matter o this product

may damage the exterior  nish.

• Do not place containers or anything else

containing liquid on top of this product. Also,

whenever any liquid has been spilled on the

surface of this product, be sure to promptly wipe

it away using a soft, dry cloth.

Maintenance

• If the unit should become soiled, wipe it with a

soft dry cloth or a  rmly wrung-out cloth. Wipe

with even pressure across the entire unit. The

 nish may be damaged if you strongly rub only a

speci c location.

• Never use benzine, thinners, alcohol or

solvents of any kind, to avoid the possibility of

discoloration and/or deformation.

Additional Precautions

• Do not apply excessive force to the height

adjustment handle, since this could cause

malfunctions.

• When you need to transport this product, pack

it in shock-absorbent material. Transporting

this product without doing so can cause it to

become scratched or damaged, and could lead

to malfunction.

• When adjusting the height of the seating

surface, take care not to pinch your  ngers in the

movable parts. If the unit is used where small

children are present, you must provide adult

supervision and guidance.

• This unit is a bench speci cally designed for

use with musical instruments. Use it only when

playing a musical instrument. Sit on the center

of the bench.

• In some cases, the color of your clothing might

transfer to the seating surface. Do not use this

bench when wearing dark-colored clothing.

• If you use this bench on a wood  oor or a woven

mat, the legs of the bench could leave marks on

its surface. In such cases, we recommend that

you place a rug or similar protective surface

under the bench.

• If you tighten the height adjustment handle

excessively, it may stop working.

* 5100041312- 01*

WARNING

This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.

For C.A. US (Proposition 65)

Roland is a registered trade mark of Roland Corporation in the United States and/or other countries.

Produkt Specifikationer

Mærke:	Roland
Kategori:	Ikke kategoriseret
Model:	BNC-05BK2
Produktfarve:	Sort
Sammenfoldelig:	Ingen
Produkttype:	Musikerbænk
Fodskammel:	Ingen
Ryglæn:	Ingen
Sæde, farve:	Sort