Roland JX-08 Manual

Roland Syntese maskine JX-08

Læs nedenfor 📖 manual på dansk for Roland JX-08 (1 sider) i kategorien Syntese maskine. Denne guide var nyttig for 18 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

JX-08 Quick Start

Panel Descriptions

Top Panel (Control Section)

5 6 7 8

No. Name Explanation

[ARPEGGIO] button

Turns the arpeggio on/o.

Long-press the button to show the

arpeggio settings menu.

[NOTE] button When this is on, you can use the [1]–[13]

buttons as a keyboard.

[SEQ] button When this is on, you can edit the sequencer.

[START] button

Plays back (the button lights up) or stops

the sequencer (the button goes dark).

Use this together with the [1]–[16] buttons

to switch to dierent patterns.

[MENU] button

Displays the sequencer settings menu.

When the [SEQ] button is on, this displays

the sequencer settings menu.

[VALUE] knob Edits the parameter’s value. Press the knob

to conrm the value or operation.

Display Shows the bank and patch number,

parameter value and tempo.

[1]–[16], [PAGE/TIE]

button

Use these buttons to switch between tones

(patch/bank), and to input notes into the

sequencer.

Tone section

(controls inside

the outlined

section)

Use these controls to edit the tones. Refer

to the manual on our website for details.

Rear Panel

10 11 12 13 14 15 16

* To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

No. Name Explanation

[POWER]

switch This turns the power on/o.

USB Type-C®

port

Use a commercially available USB Type-C cable to

connect this port to your computer. It can be

used to transfer USB MIDI and USB audio data.

You must install the USB driver when connecting

the JX-08 to your computer. Download the USB

driver from the Roland website.

https://www.roland.com/global/support/

[VOLUME]

knob Adjusts the volume.

PHONES jack Connect headphones (sold separately) here.

OUTPUT jack Connect this jack to your amp or monitor speakers.

MIX IN jack

This is the audio input jack. Sound from the

connected device is output from the PHONES jack

and OUTPUT jack.

MIDI

connectors

Connect a MIDI device to these connectors using

a commercially available MIDI cable. This lets you

control the connected MIDI devices from this unit.

Outputting Sound

1. Turn the JX-08 power on.

* Before turning the unit on/o, always be sure to turn the volume

down. Even with the volume turned down, you might hear some

sound when switching the unit on/o. However, this is normal

and does not indicate a malfunction.

2. Hold down the [START] button and press the [9]–

[16] buttons (NUMBER 1–8).

Select a pattern. The pattern number appears on the display.

3. Press the [START] button.

This plays back the pattern. Press the [START] button again to stop the

pattern.

Online Manual

For more details on this unit, refer to the online manual

(HTML) by accessing the link below.

https://roland.cm/jx-08_om

Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (the leaet “USING THE UNIT SAFELY”). After reading, keep

the document(s) where it will be available for immediate reference.

Produkt Specifikationer

Mærke:	Roland
Kategori:	Syntese maskine
Model:	JX-08
Produktfarve:	Sort
Produkttype:	Digital synthesizer
Udgange til hovedtelefoner:	1
Knapper med baggrundsbelysning:	Ja
Strømkilde type:	Battery,USB
Baggrundsfarve:	Rød
Batteritype:	AA
Antal understøttede batterier:	6
Antal USB-porte:	1
Lydeffekter:	Chorus,Compression,Delay,Overdrive,Phaser,Pitch shift
MIDI udgang:	Ja
MIDI indgang:	Ja
Lydeffekter, antal:	12
Efterklangstyper, antal:	4
Antal forudindstillede programmer:	256