Rosco LED VariColor Manual

Rosco Lys LED VariColor

Læs nedenfor 📖 manual på dansk for Rosco LED VariColor (1 sider) i kategorien Lys. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
4 Channel RF Remote Controller User Guidelines
PAIRING RF REMOTE CONTROLLER WITH RECEIVER:
1. Power up RF Remote Controller. Press the RF Code Key on Receiver.
2. Press any button on RF Controller. Connected lights on Receiver will blink once to confirm pairing was successful.
3. To Delete pairing press and hold RF Code Key on Receiver for 3 seconds. Connected lights will flash twice.
Note: One Controller can be paired with up to 10 Receivers.
RoscoLED® VariColor
White Spectrum Presets
Tap to switch through warm white, neutral white or cool
white. (Uses RGB color mixing)
Color Wheel
Touch to select color, or drag finger to fine tune to a
precise color using color mixing. This will allow you to
utilize the full capacity of your RoscoLED tape color
spectrum in a more precise manor.
Green Channel
Click to turn on/off green output. Press and hold down to
increase/decrease the light intensity/brightness of the
channel.
White Channel
Click to turn on/off white output. Press and hold down to
increase/decrease the light intensity/brightness of the
channel.
Scene 2
Press and hold down to save current outputs. Click to
recall the saved color/effect you saved. You can save up
to two colors by repeating this process for S1.
Play/Pause Presets
Click once to scroll through the 10 preset colors. Click
again to pause on any color. This will allow you to use the
preset in static mode. Holding down this button will
increase the scroll speed. Quickly releasing and holding it
down a second time will decrease scroll speed.
Power On/Off
Press to turn on/off power to the remote.
Red Channel
Click to turn on/off red output. Press and
hold down to increase/decrease the light
intensity/brightness of the channel.
Brightness/Light Intensity
Press and hold to dim up/down the light intensity of
current output. Can be used on a preset
color, or when you dial in your own selections.
Scene 1
LED Indicator
This will illuminate orange to indicate a response
between your finger and the remote. This ensures that
your remote should be working properly. If it does not
illuminate, click the power on button.
Blue Channel
Click to turn on/off blue output. Press and
hold down to increase/decrease the light
intensity/brightness of the channel.
R
G
B
W
S2S1
Wiring Guide for Receiver
V+ V-
AC Power
50/60Hz
L
N
G
V+
V-
OUTPUT
INPUT
12V/24V
CV PSU
VariColor LED Strip
V+ V +
R- R-
G- G-
B- B-
W- W-
RF Code K ey
RGBW LED Controller
V+
V-
INP UT
V+
R-
G-
B-
OUTPUT
W-


Produkt Specifikationer

Mærke: Rosco
Kategori: Lys
Model: LED VariColor

Har du brug for hjælp?

Hvis du har brug for hjælp til Rosco LED VariColor stil et spørgsmål nedenfor, og andre brugere vil svare dig




Lys Rosco Manualer

Lys Manualer

Nyeste Lys Manualer

Nanlite

Nanlite D672BII Manual

19 December 2024
Nanlite

Nanlite Compac 40 Manual

19 December 2024
Nanlite

Nanlite MixPad II 11C Manual

18 December 2024
Nanlite

Nanlite D672II Manual

18 December 2024
Chauvet

Chauvet WELL POD 2X6 Manual

17 December 2024
Luxli

Luxli ORC-VIOLA-M2 Manual

17 December 2024
Makita

Makita DML817 Manual

16 December 2024
Makita

Makita MT001 Manual

16 December 2024