Samlex SEC-R2 Manual


Læs nedenfor 📖 manual på dansk for Samlex SEC-R2 (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 12 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
GENERAL DESCRIPTION
Following Model Nos. of Rack Mount Assembly are available:
Model No. Description
SEC-R1 19”, 2U Height Rack Mount assembly for Mounting 1 SEC Series Desk Top Power Supply 2 YEAR WARRANTY
SEC-R2 19”, 2U Height Rack Mount assembly for Mounting 2 SEC Series Desk Top Power Supplies 2 YEAR WARRANTY
Rack Mount Assembly is designed to mount 1 or 2 SEC Series Power Supplies on a 19” Rack Frame. The following Samlex SEC Series Desk
Top Power Supplies can be installed in the above Rack Mount Assemblies:
• SEC-1212 / SEC-1212CE • SEC-1212P
• SEC-1223 / SEC-1223CE • SEC-1223P
• SEC-1235 / SEC-1235M • SEC-1235P / SEC-1235P-M
• SEC-1223BBM
The assembly consists of a 19”, 2U Height Rack Plate with tray(s) for installing the power supplies (Please see pictures above). The power
supply conveniently sits on the tray and is xed by its 4 top cover screws that easily slide into the grooves in the front and rear portions of the
edge of the tray.
ASSEMBLY INSTRUCTIONS
Tools Required: Phillips #2 Screwdriver
1. Switch OFF the SEC Power Supply and unplug the AC power cord from the AC outlet.
2. Loosen the 4 screws on the sides of the top cover of the power supply by few turns (do not remove) to create a gap between the screw
head and the surface of the plate to enable the screw to slide through the groove in the tray.
3. Align the 2 front screws over the 2 slots in the front portion of the grooves.
4. Lower the front of the power supply very carefully so that the 2 front screws are guided into the 2 slots. Now slowly push and slide the
power supply forward towards the rectangular cut in the front of the Rack Plate. While doing so, please ensure that the 2 screws at the
back of the power supply are carefully guided into the rear portion of the grooves. Slide the power supply fully forward till the front end of
the power supply sits properly in the rectangular slot in the Rack Plate.
5. Evenly tighten the 4 screws to x the power supply to the tray.
6. Install the Rack Plate Assembly with the mounted power supplies in the 19” Rack Frame.
7. Reconnect the AC power cord to the AC outlet. You are now ready to use the power supply.
Samlex America Inc.
103 - 4268 Lozells Ave.
Burnaby, BC Canada, V5A 0C6
T: 604 525 3836
F: 604 525 5221
1 800 561 5885
www.samlexamerica.com
Rack Mount
Assembly
Model: SEC-R1
Rack Mount
Assembly
Model: SEC-R2
Assembly
Instructions
Please read these
instructions before
assembling your
Rack Mount
Assembly
11008-SEC-R1-R2-0319


Produkt Specifikationer

Mærke: Samlex
Kategori: Ikke kategoriseret
Model: SEC-R2

Har du brug for hjælp?

Hvis du har brug for hjælp til Samlex SEC-R2 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Samlex Manualer

Samlex

Samlex BBM-12100 Manual

22 August 2024
Samlex

Samlex SEC-R2 Manual

22 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Inglesina

Inglesina Front Manual

22 December 2024
Inglesina

Inglesina Welcome Pod Manual

22 December 2024
Protector

Protector AS-5120 Manual

22 December 2024
Zipper

Zipper ED500FW Manual

22 December 2024
Roland

Roland PDQ-8 Manual

22 December 2024
Panasonic

Panasonic DMW-LMCH62E Manual

21 December 2024
Philips

Philips DLP2015 Manual

21 December 2024