San Jamar Oceans S890TBK Manual
San Jamar
Zeepdispenser
Oceans S890TBK
Læs nedenfor 📖 manual på dansk for San Jamar Oceans S890TBK (2 sider) i kategorien Zeepdispenser. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
S890TBK, TBL, WS
OCEANS® SOAP/HAND SANITIZER DISPENSING SYSTEM
Mounting Instructions
1. Use TAPE on mirrors, glazed tile, painted metal or unpainted metal walls. Tape will not perform satisfactorily
if wall surface is porous like brick or wood.
2. Use on all other walls as they provide the most positive long-lasting installation.SCREWS
3. Thoroughly clean wall surface and let dry. For silicone build-up, use a pumice-type cleaner or grout cleaner to clean
the surface.
IMPORTANT: After firmly placing backplate to wall surface, allow 24 hours
curing time for proper adhesion before use.
4. Open cover by inserting key and push down on key.
IMPORTANT: When dispensing soap, locate dispenser above a sink or counter.
We recommend to never locate where spillage can fall on floor
creating a hazardous condition.
NOTE: When dispensing hand sanitizer, it is recommended to affix the enclosed
hand sanitizer label on the unit’s paddle.
CAUTION:
When installing backplate with tape, allow 24 hours before using the dispenser.
NOTE:
When using viscous liquids, hold finger over dispenser opening and pump 3-5 times to prime on bulk
dispenser. It is recommended to prime valve with a small amount of water prior to adding viscous liquids.
MAINTENANCE
1. Using warm water mixed with soap from the dispenser is the best cleaning solution for all soap dispenser
parts. Pump warm water through valve periodically to flush out any contaminants or dried soap residue.
NEVER USE ABRASIVE CLEANERS.
2. Periodically give the dispenser an overall cleaning.
3. Do not disassemble the bulk soap bottle.
1-2-3 TAPE METHOD
A-B-C SCREW METHOD
1. Clean the surface and let dry. 2. Remove release paper. 3. Using the top as level,
press firmly to wall/glass for
30 seconds. Allow 24-hour
curing time before using.
A. Open cover, exposing
keyhole slots.
B. Locate and mark 3
keyholes on mounting
surface.
C. Drill holes for #6 screws
and anchors appropriate for
wall type.
Produkt Specifikationer
| Mærke: | San Jamar |
| Kategori: | Zeepdispenser |
| Model: | Oceans S890TBK |
Har du brug for hjælp?
Hvis du har brug for hjælp til San Jamar Oceans S890TBK stil et spørgsmål nedenfor, og andre brugere vil svare dig
Zeepdispenser San Jamar Manualer
24 August 2024
24 August 2024
Zeepdispenser Manualer
- Zeepdispenser Ikea
- Zeepdispenser SilverCrest
- Zeepdispenser Emerio
- Zeepdispenser Hansgrohe
- Zeepdispenser Smeg
- Zeepdispenser Miomare
- Zeepdispenser Tiger
- Zeepdispenser Homedics
- Zeepdispenser Tork
- Zeepdispenser Arendo
- Zeepdispenser DCG
- Zeepdispenser Delta
- Zeepdispenser Purell
- Zeepdispenser Micrell
- Zeepdispenser GOJO
Nyeste Zeepdispenser Manualer
18 December 2024
6 September 2024
6 September 2024
6 September 2024
3 September 2024
3 September 2024
3 September 2024
3 September 2024
1 September 2024
30 August 2024