Sanyo VWM-950 Manual

Sanyo Medieafspiller VWM-950

Læs nedenfor 📖 manual på dansk for Sanyo VWM-950 (15 sider) i kategorien Medieafspiller. Denne guide var nyttig for 34 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/15
INSTRUCTION MANUAL
Video Cassette Recorder
81VMN20401--- / HJ420UD ★★★★★
Printed in China
1. Before Using Your VCR
If channel 3 is already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Press [PLAY B
B
B
B
B] once to start playback.
4) After a few seconds, press [PLAY B
B
B
B
B] on the unit for 3 seconds.
•
The RF output channel will change to channel 4 from channel 3 and
you will see a playback picture.
•
When a picture does not appear on the TV screen, repeat step 4).
5) Press [C
C
C
C
CSTOP] to stop playback.
ANT
IN
OUT
RF Cable (supplied)
(Back of VCR)
(Back of TV) (Back of TV)
Plug the AC power cords of the VCR and TV into the AC outlets.
4
Disconnect
Antenna
or
2
Connect
3
Connect
Cable TV
Signal
Antenna
or
Cable TV
Signal
Basic TV Connection
RF Output Channel
Select this connection when you want to view or record a
scrambled channel.
With this connection, channels cannot
be changed on the VCR. You can view or record ONLY the
channels you have selected on the cable box or the satellite
box.
• While you are recording, only the recorded channel can
be viewed.
T
o select channels of the cable box or satellite box
1) Turn on the unit by pressing [POWER], then press
[VCR/TV]. The “POWER”and the “VCR/TV”lights on
the front panel will appear, then press
[CHANNEL ] to select channel 3 or 4 (the
same channel as the output channel of the cable box
or satellite box).
• If you use the channel 4, you need to change the
unit’s RF output to channel 4. Refer to “RF Output
Channel”.
2) On the TV, select channel 3 or 4 (the same channel as
you have selected at step 1).
3) On the cable box or satellite box, select the channel
you want to view or record.
Select this connection when you want to change channels
on the unit. With this connection, you may watch one
channel while recording another.
• You may not view or record a scrambled channel.
T
o select channels of the cable box
1) On the cable box, select channel 3 or 4 (the same
channel as the VCR’s RF output channel.)
•Refer to “RF Output Channel”.
2) On the TV, select the same channel as the output
channel (3 or 4) of the cable box.
3) Turn on the unit by pressing [POWER], then press
[VCR/TV]. The “POWER”and “VCR/TV” lights on the
front panel will appear, then select the channel you
want to view or record.
T
o play back a tape
Follow the steps 1) to 2) above, then play back a tape.
•Refer to “Playback” on page 4.
To view one channel while recording another
1)
While you are recording on the unit, press [VCR/TV].
2)On the cable box, select the channel you want to view.
Hints for Cable Box or Satellite Box
ANT
IN
OUT
RF cable
(supplied)
(Back of VCR)
IN OUT
E
(Back of TV)
Antenna
or
Cable TV
signal
Connection A
(Cable box or
Satellite box)
- 1 -
ANT
IN
OUT
RF cable RF cable(supplied) (Back of TV)
IN OUT
(Cable box)
E
Connection B
Antenna
or
Cable TV
signal
(Back of VCR)
You can use the AUDIO OUT jacks and
VIDEO OUT jack on the back of the
unit if your TV has Audio/Video Input
jacks. In this case, you need to set the
TV to external Line Input Mode. Please
refer to your TV’s owner’s manual.
Front & Rear Terminals
Stereo TV Connection
ANT
AUDIO
VIDEO
IN
OUT
OUT IN
OUT
L
R
IN
L R
AUDIO OUTVIDEO
OUT
(Back of TV)
AUDIO ANT
IN
OUT
VIDEO
OUT
L
R
IN
Audio/Video Cables
(not supplied)
L R
AUDIO INVIDEO
IN
INOUT
(Back of VCR)
• Remote control
(NA323) with
two AA batteries
• RF cable Instruction manual•
Supplied Accessory Installing the Batteries for
the Remote Control
Install two AA batteries
(supplied) matching the
polarity indicated on
the bottom of the
remote control.
ANT
AUDIO
VIDEO
IN
O UT
O UT IN
O UT
L
R
IN
ANT
AUDIO
VIDEO
IN
OUT
OUT IN
OUT
L
R
IN
VIDEO IN jack
Connect the video cable coming from the
video output jack of a camcorder, another
VCR or an audio-visual source (laser disc
player, video disc player, etc.) here.
POWE R
VCR/T V
T APE IN
MENU
T IMER
REC
CHANNEL
POWER
L–AUDIO–RVIDEO
AV INPUT
•
Quick setup guide
Qu ick Se t up Guide
VWM-950
VIDEO OUT jack
Connect the video cable here through the
video input jack of a camcorder, another
VCR or a TV.
ANT IN jack
Connect your antenna or cable box
here.
ANT OUT jack
Connect the supplied RF cable to the
antenna input jack on your TV.
AUDIO IN jacks
Connect the audio cables coming from the
audio output jacks of a camcorder, another
VCR or an audio source here.
AUDIO OUT jacks
Connect the audio cables here through to
the audio input jacks of a camcorder, another
VCR, a stereo amplifier or an audio system.
Hint
Hint
• The RF output channel may not
change when you adjust track-
ing during playback. In this
case, stop the playback, and
start the playback again. After
that, press [PLAY B
B
B
B
B] on the
VCR for 3 seconds again.

Produkt Specifikationer

Mærke: Sanyo
Kategori: Medieafspiller
Model: VWM-950

Har du brug for hjælp?

Hvis du har brug for hjælp til Sanyo VWM-950 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Medieafspiller Sanyo Manualer

Sanyo

Sanyo VWM-950 Manual

17 Februar 2024
Sanyo

Sanyo HMP200 Manual

30 December 2023
Sanyo

Sanyo HMP130 Manual

10 Januar 2023

Medieafspiller Manualer

Nyeste Medieafspiller Manualer

Philips

Philips DVP3250K Manual

12 December 2024
Philips

Philips PET726B Manual

12 December 2024
Philips

Philips PET724B Manual

12 December 2024
Philips

Philips DVP5106K Manual

12 December 2024
Philips

Philips DVP3008 Manual

12 December 2024
Philips

Philips DVP3028 Manual

12 December 2024
Philips

Philips DVP3747 Manual

12 December 2024
Philips

Philips DVP3030A Manual

12 December 2024
Pure Acoustics

Pure Acoustics Jolt X225 Manual

8 December 2024
Pure Acoustics

Pure Acoustics Jolt 245 Manual

8 December 2024