Sharp XE-A101 Manual

Sharp Kasseapparat XE-A101

Læs nedenfor 📖 manual på dansk for Sharp XE-A101 (4 sider) i kategorien Kasseapparat. Denne guide var nyttig for 19 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

5. Attach the printer cover.

CImproper use of batteries could cause

them to burst or leak, which might damage

the interior of the cash register. Please

take the following precautions:

Be sure that the positive (+) and negative

(-) poles of each battery are oriented

properly. .

•Never mix batteries of different types.

•Never mix old batteries and new ones.

•Never leave dead batteries in the battery

compartment.

•Remove the batteries if you plan not to

use the cash register for long periods.

Should a battery leak, clean out the

battery compartment immediately, taking

care not to let the battery fluid come into

direct contact with your skin.

Installing a Paper Roll

Always install the paper roll even when you set the

mode.

1. Push the printer cover forward and detach it.

2. Push the paper roll release lever and install

the paper roll so that the paper unrolls from

the bottom.

Tax 1

SBTL @/TM @/TM

Tax rate(7.0000%) Min. taxable

amount($0.11)

Changing Other Settings As Necessary

Your cash register is pre-programmed so that you

can use it with minimum setup. To change the initial

settings, see the appropriate sections.

Initial Settings

Departments 1 to 4:

Taxable 1. Positive (+). Preset price: 0.00

Departments 5 to 8:

Non-taxable. Positive (+). Preset price: 0.00

PLU codes 1-10:

Assigned to dept. 1. Preset price: 0.00

PLU codes 11-80:

Not used

When you program the tax status for a department,

tax will be automatically added to sales of items

assigned to the department according to the

programmed tax status for the department. You can

also enter tax manually.

There are two tax programming methods. The tax

rate method uses a straight percentage rate per

dollar. The tax table method requires tax break

information from your state or local tax offices. Use

the method which is acceptable in your state. You

can obtain necessary data for tax programming from

your local tax office.

D For tax table programming, see "programming"

Tax Rate Programming

The percent rate specified here is used for tax

calculation on taxable subtotals. Set the mode

switch to the Z/PGM position and use the following

sequence to program the tax rate:

➝#/

SBTL ➝ Tax number(1-4) ➝

@/TM

➝ R

➝

@/TM

➝ Q ➝

where R and Q represent the following.

R: Tax rate (0.0000% to 99.9999%) x 10000

Enter the rate in 6 digits (leading zeros may be

omitted). If the rate is fractional (e.g., 4 3/8%), it

should be converted to its decimal equivalent

(4.375) before entering.

Q: Minimum taxable amount (0.01 to 99.99) x 100

Smallest amount for which tax must be collected. In

some states, sales whose amounts are less than the

minimum taxable amount are not subject to tax. If

amounts $0.01 to $0.10 are not taxed, the value of

Q would be 11 (for $0.11), the lowest of the first

taxable category.

Time(2:30 p.m.)

SBTL

DDD Always enter the date in 6 digits. For

example, enter

for March

15, 2002. If you change the date format in

the Z/PGM mode, follow the newly specified

format when setting the date.

Checking the Time and Date

You can display the time and date to check if they

are correctly set.

1. Set the mode switch in the REG position.

2. Press the

@/TM

key once to display the time.

3. Press the

@/TM

key a second time to display the

date.

Programming the Tax Rate

Before you can proceed with registration of sales,

you must first program the tax that is levied in

accordance with the law of your state. Your cash

different tax rates. In most states, you will only

need to program Tax 1. However, if you live in an

area that has a separate local tax (such as a Parish

tax) or a hospitality tax, your register can be

programmed to calculate these separate taxes.

In order to program the tax to be collected in

accordance with the law of your state, you must

specify the tax rate(s) and minimum taxable

amount(s).

D•Always enter the time in 4 digits even when

the hour is in the single digit. For example,

enter

for 6:30 a.m.

• “ ” 6:30 a.m. prints as 6-30 and 6:30 p.m.

prints as “6-30@”.

Setting the Date

In the Z/PGM mode, enter the date in 6 digits using

the month-day-year format. Press the

SBTL

key once

to continue programming or twice to exit the

program mode.

5. Attach the printer cover.

(For receipt printing, step 4 should be omitted.)

Setting the Time

Set the mode switch to the Z/PGM position and

enter the time in 4 digits ( format) using the“hhmm”

24 hour system. Press the

SBTL

key once to continue

programming or twice to exit the program mode.

3. Insert three new AA batteries.

Initializing the Cash Register

For your cash register to operate properly, you must

initialize it before programming for the first time.

Follow this procedure.

1. Remove the register from its packing carton.

2. Set the mode switch to the REG position.

3. Insert the plug into the AC outlet.

IMPORTANT: This operation must be performed

without batteries loaded.

4. The buzzer will sound three times. Now your

cash register has been initialized. The display

will show "0.00" with “lllll”.

Installing Batteries

Batteries must be installed in the cash register to

prevent data and programmed contents from being

lost from the memory in case of accidental

disconnection of the AC cord or power failure. Please

install three new batteries before programming“AA”

and operating the cash register. Once installed, the

batteries will last approximately one year. When it is

time to replace them, the symbol will appear on“ ”l

the display to indicate a low battery voltage. If the

symbol appears, you must replace them within two

days.

Install the batteries according to this procedure with

the AC cord connected:

1. Push the printer cover forward and detach it.

4. When the batteries are properly installed, “lllll”

on the display will disappear. Close the battery

cover.

Thank you for purchasing the SHARP Electronic Cash Register Model XE-A101. Please

read this manual carefully before operating your machine. Keep this manual for future

reference. It will help you solve any operational problems that you may encounter.

For assistance call

1-800-BE-SHARP

SHARP ELECTRONIC CASH REGISTER MODEL

XE-A101

INSTRUCTION MANUAL

WARNING

FCC Regulations state that any unauthorized changes or modifications to this equipment not

expressly approved by the manufacturer could void the user’s authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when this equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

CAUTION

The socket-outlet shall be installed near the equipment and shall be easily accessible.

FOR YOUR RECORDS

Please record below the model number and serial number, for easy reference, in case of loss or theft.

These numbers are located on the right side of the unit. Space is provided for further pertinent data.

Model Number_______________________________________________________

Serial Number_______________________________________________________

Date of Purchase_____________________________________________________

Place of Purchase____________________________________________________

Handling Cautions

Install the cash register in a location not subject to direct sunlight, unusual temperature

changes, high humidity, or splashing water.

Do not operate the cash register with wet hands. Water can cause internal component failure.

The cash register plugs into any standard wall outlet (120V AC 10%). Avoid connecting any±

other electrical devices on the same electrical circuit since such connection could cause the

cash register to malfunction.

When cleaning the cash register, use a dry, soft cloth. Never use volatile liquids, such as

benzine or thinner. Chemicals can discolor or damage the cabinet.

For protection against data loss, please install three new batteries before using the cash“AA”

batteries; otherwise damage to memory contents or malfunctioning of the register will occur. You

can start operating it only after initializing it and then installing batteries.

For complete electrical disconnection, pull out the main plug.

Printed in Korea

O(TINSE2457BHZZ) 2

Getting Started

For Easy Set-up,

See “Getting Started”

View from rear

2. Open the battery cover next to the paper roll

cradle.

3. Insert the paper straight into the paper inlet,

and press the ff

f key. The inserted end

comes out at the printing area.

4. (For journal printing) Insert the top end of

the paper into the slit in the take-up spool

shaft and wind the paper two or three turns.

Then place the take-up spool on the bearing.

Date(March 15, 2002)

SBTL

Produkt Specifikationer

Mærke:	Sharp
Kategori:	Kasseapparat
Model:	XE-A101

Har du brug for hjælp?

Hvis du har brug for hjælp til Sharp XE-A101 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Kasseapparat Sharp Manualer

12 December 2024

12 Maj 2024

14 April 2024

19 Marts 2024

28 Februar 2024

28 Oktober 2023

Sharp XE-A137-WH Manual

17 August 2023

Sharp XE-A201 Manual

23 Maj 2023

Sharp XEA-147BK Manual

27 Januar 2023

Sharp ER-A220 C Manual

8 December 2022

Kasseapparat Manualer

Nyeste Kasseapparat Manualer

AOpen AT1032TB Manual

26 November 2024

AOpen eTile-X AT10M-FP Manual

26 November 2024

AOpen eTile-X AT15M-FB Manual

26 November 2024

AOpen eTile-X AT19M-FB Manual

20 November 2024

AOpen eTILE WT22M-FW Manual

20 November 2024

Posiflex ZT-3115 Manual

20 September 2024

Posiflex RT-2016-G2 Manual

19 September 2024

Posiflex RT-6016Q-G2 Manual

19 September 2024

Posiflex RT-6015Q-G2 Manual

19 September 2024

Posiflex RT-1016A-G2 Manual

19 September 2024