Sharp XEA-206 Manual

Sharp Boks XEA-206

Læs gratis den danske manual til Sharp XEA-206 (4 sider) i kategorien Boks. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Sharp XEA-206, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

XE-A206 Quick Start Guide

The following describes how to get the cash register ready for operate. Follow these steps before you use the cash register for the first time.

Before you set up the cash register, prepare three new alkaline batteries LR6 ("AA" size) which are necessary for memory backup. Find a stable and flat surface not subject to direct radiation, to place

the cash register.

English

1Initializing the Cash Register

To ensure the cash register operates properly, please use the following

procedure:

1. Make sure the power cord is unplugged and batteries are not

installed on the register.

2. Insert the manager (MA) key into the mode switch and turn it to the

REG position.

3. Insert the plug of the power cord into the AC outlet. The buzzer will

sound three times.

IMPORTANT: This operation must be performed without batteries installed.

4. The cash register has now been initialized.

The register display will show “0.00” with “ ”.

2Installing the Batteries

1. Push the printer cover forward and detach it.

2. Open the battery compartment cover next to the paper roll cradle.

3. Install three new alkaline batteries LR6 (“AA” size) as shown at the

right. (Batteries are not supplied with the cash register.) Make sure

that positive (+) and negative (–) poles of each battery are properly

oriented.

4. When the batteries are properly installed, “ ” on the display will

disappear. Close the battery compartment cover.

3Installing the Paper Roll (for receipt printing)

If you want to use a paper roll for journal printing, please refer to GETTING

STARTED section of the instruction manual.

1. Lift up the print roller release lever to unlock and open the print roller arm.

2. Set a paper roll in the paper roll cradle as illustrated right.

NOTE: When setting a new paper roll in the paper roll cradle, be sure to cut

the paper end behind the taped (or pasted) point in advance.

3. Feed the end of the paper along with the paper positioning guides

as illustrated at the right.

4. While holding down the paper, slowly close the print roller arm, and

push down the arm until you hear a click locking the arm.

Make sure you securely push down the center of the wing part of the

arm as illustrated at the right. The paper will be fed automatically.

5. Cut off the excess paper using the edge of the inner cover, and

replace the printer cover. Press the Fkey to make sure the paper

end comes out of the printer cover and clean paper appears.

NOTE: If the print roller arm is not securely locked, the unit will not print correctly.

If this problem occurs, open the arm, and close the arm as instructed

above.

REG

OPX/Z MGR

PGM

X1/Z1

X2/Z2

OFF

VOID

Print roller arm

Print roller release lever

To the printe

Incorrect

To the printe

Correct

Paper positioning

guides

Produkt Specifikationer

Mærke:	Sharp
Kategori:	Boks
Model:	XEA-206

Har du brug for hjælp?

Hvis du har brug for hjælp til Sharp XEA-206 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Boks Sharp Manualer

14 September 2024

14 August 2024

7 August 2024

3 August 2024

2 August 2024

Sharp XE-A137-BK Manual

1 August 2024

28 Juli 2024

27 Juli 2024

26 Juli 2024

23 Juli 2024

Boks Manualer

Nyeste Boks Manualer

Posiflex GT-7116A Manual

19 Februar 2025

Posiflex BT-2015 Manual

19 Februar 2025

Posiflex KDS-4321 Manual

19 Februar 2025

3 Januar 2025

28 December 2024

28 December 2024

28 December 2024

28 December 2024

27 December 2024

27 December 2024