Sharp XEA-106 Manual

Sharp Boks XEA-106

Læs nedenfor 📖 manual på dansk for Sharp XEA-106 (4 sider) i kategorien Boks. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

Installing a Paper Roll

Always install the paper roll even when you set the

1. Push the printer cover forward and detach it.

2. Place a paper roll in the paper roll cradle so

that the paper unrolls from the bottom.

Tax 1

@/TM @/T M

Tax rate (7.0000%) Min. taxable

amount ($0.11)

SBTL

Changing Other Settings As Necessary

Your cash register is pre-programmed so that you

can use it with minimum setup. To change the initial

settings, see the appropriate sections.

Initial Settings

Departments 1 to 4:

Taxable 1. Positive (+). Preset price: 0.00

Departments 5 to 8:

Non-taxable. Positive (+). Preset price: 0.00

PLU codes 1-10:

Assigned to dept. 1. Preset price: 0.00

PLU codes 11-80:

Not used

When you program the tax status for a department,

tax will be automatically added to sales of items

assigned to the department according to the

programmed tax status for the department. You can

also enter tax manually.

There are two tax programming methods. The tax

rate method uses a straight percentage rate per

dollar. The tax table method requires tax break

information from your state or local tax offices. Use

the method which is acceptable in your state. You

can obtain necessary data for tax programming from

your local tax office.

D For tax table programming, see "programming"

Tax Rate Programming

The percent rate specified here is used for tax

calculation on taxable subtotals. Turn the mode

switch to the Z/PGM position and use the following

sequence to program the tax rate:

➝

SBTL

Tax number(1-4) ➝ ➝

@/TM

R➝

➝

@/TM

Q ➝ ➝

where R and Q represent the following.

R: Tax rate (0.0000% to 99.9999%) x 10000

Enter the rate in 6 digits (leading zeros may be

omitted). If the rate is fractional (e.g., 4 3/8%), it

should be converted to its decimal equivalent

(4.375) before entering.

Q: Minimum taxable amount (0.01 to 99.99) x 100

Smallest amount for which tax must be collected. In

some states, sales whose amounts are less than the

minimum taxable amount are not subject to tax. If

amounts $0.01 to $0.10 are not taxed, the value of

Q would be 11 (for $0.11), the lowest of the first

taxable category.

Time (2:30 p.m.)

SBTL

D Always enter the date in 6 digits. For

example, enter

for

February 15, 2010. If you change the date

format in the Z/PGM mode, follow the newly

specified format when setting the date.

DDD •Always enter the time in 4 digits even when

the hour is in the single digit. For example,

enter

for 6:30 a.m.

• 6:30 a.m. prints as “06-30” and 6:30 p.m.

prints as “06-30@”.

Setting the Time

Turn the mode switch to the Z/PGM position and

enter the time in 4 digits (“hhmm” format) using the

24 hour system. Press the #/

SBTL key once to continue

programming or twice to exit the program mode.

3. Insert three new AA batteries.

Initializing the Cash Register

For your cash register to operate properly, you must

initialize it before programming for the first time.

Follow this procedure.

1. Remove the register from its packing carton.

2. Insert the supplied mode key into the mode

switch and turn it to the REG position.

3. Insert the plug into the AC outlet.

IMPORTANT: This operation must be performed

without batteries loaded.

4. The buzzer will sound three times. Now your

cash register has been initialized. The display

will show "0.00" with “ ”.

Installing Batteries

Batteries must be installed in the cash register to

prevent data and programmed contents from being

lost from the memory in case of accidental

disconnection of the AC cord or power failure. Please

install three new “AA” batteries before programming

and operating the cash register. Once installed, the

batteries will last approximately one year. When it is

time to replace them, the “ ” symbol will appear onl

the display to indicate a low battery voltage. If the

symbol appears, you must replace them within two

days.

Install the batteries according to this procedure with

the AC cord connected:

1. Push the printer cover forward and detach it.

4. When the batteries are properly installed, “ ”

on the display will disappear. Close the battery

cover.

5. Attach the printer cover.

Thank you for purchasing the SHARP Electronic Cash Register Model XE-A106. Please

read this manual carefully before operating your machine. Keep this manual for future

reference. It will help you solve any operational problems that you may encounter.

For assistance call

1-800-BE-SHARP

SHARP ELECTRONIC CASH REGISTER MODEL

XE-A106

INSTRUCTION MANUAL

WARNING

FCC Regulations state that any unauthorized changes or modifications to this equipment not

expressly approved by the manufacturer could void the user’s authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

CAUTION

The socket-outlet shall be installed near the equipment and shall be easily accessible.

FOR YOUR RECORDS

Please record below the model number and serial number, for easy reference, in case of loss or theft.

These numbers are located on the right side of the unit. Space is provided for further pertinent data.

Model Number_______________________________________________________

Serial Number_______________________________________________________

Date of Purchase_____________________________________________________

Place of Purchase____________________________________________________

Handling Cautions

Install the cash register in a location not subject to direct sunlight, unusual temperature

changes, high humidity, or splashing water.

Do not operate the cash register with wet hands. Water can cause internal component failure.

The cash register plugs into any standard wall outlet (120V AC 10%). Avoid connecting any±

other electrical devices on the same electrical circuit since such connection could cause the

cash register to malfunction.

When cleaning the cash register, use a dry, soft cloth. Never use volatile liquids, such as

benzine or thinner. Chemicals can discolor or damage the cabinet.

For protection against data loss, please install three new “AA” batteries before using the cash

batteries; otherwise damage to memory contents or malfunctioning of the register will occur. You

can start operating it only after initializing it and then installing batteries.

For complete electrical disconnection, pull out the main plug.

Printed in China

O(TINSE2598RCZZ) 1

Getting Started

For Easy Set-up,

See “Getting Started”

View from rear

2. Open the battery cover next to the paper roll

cradle.

3. Insert the paper straight into the paper inlet,

and press the ff

f key. The inserted end

comes out at the printing area.

4. (For journal printing)

11111Insert the top end of the paper into the

slit in the take-up spool shaft and fold

the inserted end toward you.

2Wind the paper two or three turns.

3Mount the paper holding plate onto the

take-up spool.

44444Place the take-up spool on the bearing.

Date (February 15, 2010)

SBTL

Put the spool shaft in the larger hole of the paper

holding plate and push the plate in the direction

of the arrow.

5. Attach the printer cover.

(For receipt printing, step 4 should be omitted.)

Programming the Tax Rate

Before you can proceed with registration of sales,

you must first program the tax that is levied in

accordance with the law of your state. Your cash

different tax rates. In most states, you will only

need to program Tax 1. However, if you live in an

area that has a separate local tax (such as a Parish

tax) or a hospitality tax, your register can be

programmed to calculate these separate taxes.

In order to program the tax to be collected in

accordance with the law of your state, you must

specify the tax rate(s) and minimum taxable

amount(s).

Checking the Time and Date

You can display the time and date to check if they

are correctly set.

1. Turn the mode switch in the REG position.

2. Press the

@/TM

key once to display the time.

3. Press the

@/TM

key a second time to display the

date.

Setting the Date

In the Z/PGM mode, enter the date in 6 digits using

the month-day-year format. Press the #/

SBTL key once

to continue programming or twice to exit the

program mode.

DDDBefore placing a new paper roll in the paper

roll cradle, cut off the pasted (taped) part of

the paper and confirm that the cut end of the

paper is straight.

Maintenance

Batteries

This cash register provides a low battery symbol

( ) and a no battery symbol ( ) which appears onl

the far left of the display in one of the following

situations:

Low battery symbol ( )l

• When the voltage of the batteries installed in the

cash register is under the required level.

No battery symbol ( )

• When three batteries are not installed in the cash

• When the batteries installed in the cash register

are dead.

When either of these symbols appear, check

batteries. If no batteries are installed, install three

new “AA” batteries at once. If batteries are already

installed, replace them with new ones as soon as

possible. If the AC power cord is disconnected or a

power failure occurs when the batteries are dead

or not installed, all the programmed settings will be

reset to the default settings and any data stored in

memory will be cleared.

DIf the low battery symbol appears while

making a transaction, complete the

transaction before replacing the batteries.

Improper use of batteries could cause them to burst

or leak, which might damage the interior of the cash

•Be sure that the positive (+) and negative (-) poles

of each battery are oriented properly.

•Never mix batteries of different types.

•Never mix old batteries and new ones.

•Never leave dead batteries in the battery

compartment.

•Remove the batteries if you plan not to use the cash

•Should a battery leak, clean out the battery

compartment immediately, taking care not to let the

battery fluid come into direct contact with your skin.

•If an incorrect battery is used, it may explode or

leak.

•For battery disposal, follow the relevant law or

regulation in your country.

Replacement

1. Be sure the cash register is plugged in.

2. Turn the mode switch to the REG position.

6. Check that the “ ” symbol has disappeared.

7. Close the battery cover.

8. Replace the printer cover.

C Improper use of batteries could cause them

to burst or leak, which might damage the

interior of the machine. See the cautions in

the "Getting Started" section.

Paper Roll

When colored dye appears on the edges of the

paper roll, it is time to replace the roll. Use paper

of 2 1/4" (57 mm) in width. To prevent jamming be

sure to use paper specified by SHARP.

Replacement (Journal printing)

1. Turn the mode switch to the REG position.

2. Open the printer cover.

3. Press to advance the paper by several f

lines and then cut the paper to remove the

take-up spool from the bearing.

5. Install three new “AA” batteries into the

battery compartment.

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07495-1163

1-800-BE-SHARP

http://www.sharpusa.com

Drawer Handling

Locking the Drawer

Develop the habit of locking the drawer when not

using the register for any extended period of time.

To lock: Insert the key into the drawer lock and

turn it 90 degrees counter-clockwise.

To unlock: Insert the key into the drawer lock and

turn it 90 degrees clockwise.

Removing the Drawer

To remove the drawer, pull it out and lift it up.

D• To prevent burglary, it is a good idea to

empty the drawer after work and leave it

open at the end of the day.

• Coin case is detachable. Also the

separators of the coin case are

removable.

Manually Opening the Drawer

In case of a power failure or if the machine is out of

order, locate the lever at the bottom of the machine

and move it in the direction of the arrow to open

the drawer. The drawer will not open if it is locked

with the drawer lock key.

Coin case

View from rear

4. After cutting the existing paper, remove the

paper roll. Then remove the remaining paper

by pressing f .

5. Remove the paper holding plate from the

spool.

View from rear

4. Open the battery cover and remove the old

batteries.

6. Remove the used journal paper roll (if used)

from the take-up spool.

7. Install a new paper roll, the paper holding

plate and the take-up spool according to the

instructions in "Getting Started."

C In the case of receipt printing, steps 3, 5 and

6 should be omitted and the paper holding

plate and the take-up spool need not be

installed in step 7.

Replacing the Ink Roller

1. Open the printer cover.

2. Remove the ink roller by pulling it upward.

3. Install a new ink roller.

4. Close the printer cover.

Installing the Mounting

Bracket

How to attach the mounting bracket

1.Thoroughly clean the table surface where you

wish to place the bracket (B).

2.Peel off the release paper of the adhesive tape

on the bracket.

3.Hook the bracket onto the hook (A) at the

bottom of the back of the register.

4.Hold down the bracket so that it firmly sticks to

the table surface.

How to release the register from the mounting

bracket

Lift up the front of the register and pull it towards

you.

A mounting bracket which prevents the register

from moving accidentally is supplied with your

XE-A106 register. Attach the bracket to a table

where the register rests, as follows:

Specifications

Model:

XE-A106

Size:

Inches: 13.0 (W) x 14.3 (D) x 9.21 (H)

Millimeters: 330 (W) x 363 (D) x 234 (H)

Weight:

Approx. 11.0 lbs. (5.0 kg)

Power Source:

120V AC±10%, 60Hz

Power Consumption:

Stand-by: 4 W, Operating: 12.5 W

Working Temperature:

32 to 104˚F (0 to 40˚C)

Display:

LED (Light-Emitting Diode) numeric display

Printer:

1 station, print wheel selective type

Printing Capacity:

Max. 13 characters

Paper Roll:

Width: 2 1/4" + 1/64" (57.5mm + 0.5mm)

Max. external diameter: 3-5/32" (80mm)

Min. internal diameter: 15/32" (12mm)

Cash Drawer:

4 slots for bills, 5 for coins

Accessories (supplied):

Paper roll: 1 roll

Mode key: 1

Drawer lock key: 1

Instruction manual (English): 1 copy

Instruction manual (Spanish): 1 copy

Quick Start Guide (English): 1 copy

Quick Start Guide (Spanish): 1 copy

Ink roller: 1 (installed)

Take-up spool: 1

Paper holding plate: 1

Mounting bracket: 1

• Specifications and appearance are subject to

change without notice for improvement.

Before Calling for Service

If you encounter any of the following problems,

please read below before calling for service.

The display shows symbols that do not make

sense.

• Has the machine been initialized properly as

shown in “Getting Started”?

The display will not illuminate while the

machine is turned on. The machine will not

operate when any key is pressed.

• Is the power supplied to the electrical outlet?

(Plug another electrical device into the outlet for

confirmation.)

• Is the power cord firmly connected to the

electrical outlet?

The display is illuminated, but the machine will

not accept key entries.

• Is the mode switch properly set to the REG

position?

• Has the machine been initialized properly as

shown in “Getting Started”?

Journal paper will not feed properly in the printer.

• Is the take-up spool installed properly?

• Is there a paper jam?

• Is the journal format selected in the printing

format programming?

(If the receipt format is selected, the paper is not

wound around the take-up spool.)

Printing is faded or illegible.

• Is the ink roller used up?

• Has the ink roller been installed properly?

Lever

Push this part in the direction of the

arrow to remove paper holding plate.

END-USER LIMITED WARRANTY

Model Specific Section (Carry-in Service)

Your Product Model Number & Description: XE-A106 Cash Register

(Be sure to have this information available when you need

service for your product.)

Warranty Period for this Product: One (1) Year Parts and 90 Days labor from date of purchase

Additional Item(s) Excluded from

Warranty Coverage (if any): Any consumable items such as paper supplied with the Product.

Where to Obtain Service: From a Sharp Authorized Servicer located in the United States.

To find the location of the nearest Sharp Authorized Servicer,

call Sharp toll free at 1- 800-BE-SHARP.

What to do to Obtain Service: Ship prepaid or carry in your Product to a Sharp

Authorized Servicer. Be sure to have Proof of Purchase

available. If you ship the Product, be sure it is insured and

packaged securely.

TO OBTAIN PRODUCT INFORMATION, CALL 1-800-BE-SHARP OR VISIT www.sharpusa.com.

SHARP ELECTRONICS CORPORATION warrants to the first end-user purchaser (the “Purchaser”) that this Sharp

brand product (the “Product”), when new and shipped in its original container, will be free from defective

workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective

Product or part thereof with a new or remanufactured equivalent at no charge to the Purchaser for parts or labor for

the period(s) set forth below.

This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth

below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper

voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or

construction.

In order to enforce the rights under this limited warranty, the Purchaser should follow the steps set forth below and

provide proof of purchase to the servicer.

To the extent permitted by applicable state law, the warranties set forth herein are in lieu of, and exclusive of, all

other warranties, express or implied. Specifically, ALL OTHER WARRANTIES OTHER THAN THOSE SET FORTH

ABOVE ARE EXCLUDED. ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF

MERCHANTABILITY, FITNESS FOR USE, AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY

EXCLUDED. If, under applicable warranties is limited to the period(s) from the date of purchase set forth below.

Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those

described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of

Sharp.

The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole

and exclusive remedy available to the Purchaser. Correction of defects, in the manner and for the period of time

described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the Purchaser

with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence,

strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects

in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized

servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or

property damage. Some states do not allow limits on warranties or on remedies for breach in certain transactions; in

such states, the limits herein may not apply.

3. Pull the printer cover upward and detach it.

Produkt Specifikationer

Mærke:	Sharp
Kategori:	Boks
Model:	XEA-106

Har du brug for hjælp?

Hvis du har brug for hjælp til Sharp XEA-106 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Boks Sharp Manualer

14 September 2024

14 August 2024

7 August 2024

3 August 2024

2 August 2024

Sharp XE-A137-BK Manual

1 August 2024

28 Juli 2024

27 Juli 2024

26 Juli 2024

23 Juli 2024

Boks Manualer

Nyeste Boks Manualer

Sam4S ER-945 Manual

8 September 2024

Posiflex XT-3817-G2 Manual

6 September 2024

Posiflex ZT-3716 Manual

6 September 2024

Posiflex RT-6116 Manual

6 September 2024

Posiflex ZT-3116 Manual

6 September 2024

Posiflex RT-6016-G2 Manual

6 September 2024

Posiflex RT-6016 Manual

6 September 2024

Posiflex RT-6015 Manual

6 September 2024

Posiflex RT-6015-G2 Manual

6 September 2024

Posiflex RT-2015-G2 Manual

6 September 2024