Shimano CT-S500 Manual
Shimano
Cykel tilbehør
CT-S500
Læs nedenfor 📖 manual på dansk for Shimano CT-S500 (1 sider) i kategorien Cykel tilbehør. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/1
Technical Service Instructions
CT-S500
SI-50D0A-001
Chain Tensioner
General Safety Information
Clean the chain tensioner periodically and lubricate all moving parts and
pulleys.
If there is a large amount of play in the pulleys and an abnormal amount of
noise is generated while riding, replace the pulleys.
Parts are not guaranteed against natural wear or deterioration resulting from
normal use.
For any questions regarding methods of handling or maintenance, please
contact the place of purchase.
NOTE:
Chain Chain tool
Reinforced
connecting pin
9-speed super narrow
chain such as
CN-7701/ CN-HG93
8- /7-/ 6-speed narrow
chain such as
CN-HG50/ CN-IG51
Silver
6.5 mm
Black
7.1 mm
TL-CN31/ TL-CN22
TL-CN31/ TL-CN22
and
TL-CN30/ TL-CN21
End pin Link pin Reinforced connecting pin Guide pulley
Sprocket
Spacer
Fixing bolt
Sprocket
Guide pulley
Tension pulley
Perpendicular to ground
Smaller chainring
CT-S500 chain tensioner
Use neutral detergent to clean the chain. Do not use alkali-based or acid-
based detergents such as rust cleaners, as they may result in damage
and/or failure of the chain.
Use the reinforced connecting pin only for connecting the narrow type of
chain.
There are two different types of reinforced connecting pins available. Be
sure to check the table below before selecting which pin to use.
if connecting pins other than reinforced connecting pins are used, or if a
reinforced connecting pin or tool which is not suitable for that type of
chain is used, sufficient connection force may not be obtained, which
could cause the chain to break or fall off.
If it is necessary to adjust the length of the chain due to a change in the
number of sprocket teeth, make the cut at some other place than the
place where the chain has been joined using a reinforced connecting pin
or an end pin.
The chain will be damaged if it is cut at a place where it has been joined
with a reinforced connecting pin or an end pin.
Check that the tension of the chain is correct and that the chain is not
damaged.
If the tension is too weak or the chain is damaged, the chain should be
replaced. If this is not done, the chain may break and cause serious
injury.
Obtain and read the service instructions carefully prior to installing
the parts. Loose, worn, or damaged parts may cause serious injury to
the rider. We strongly recommend only using genuine Shimano
replacement parts.
Read these Technical Service Instructions carefully, and keep them in a
safe place for later reference.
WARNING – To avoid serious injuries:
Be sure to read these service instructions in conjunction with the service
instructions for the hub for Inter-8 disc brake before use.
Installation of the chain tensioner to the frame
Insert a spacer in between the dropout and the chain tensioner so that the guide pulley
of the chain tensioner is directly below the sprocket, and then tighten the fixing bolt.
One spacer with a thickness of 1 mm and two spacers with a thickness of 2 mm are
included.
The total thickness of spacers used should not exceed 5 mm.
Chain length
If the different between the number of teeth on the chainrings is 12T or less, or if the
front chainwheel has a single chainring, set the chain onto the smaller chainring, and
then set the chain tensioner so that the tension pulley and guide pulley are
perpendicular to the ground.
Specifications
Front chainwheel tooth difference
Largest sprocket
Smallest sprocket
Applicable dropout width
16T
20T
18T
5 – 9 mm
Tightening torque:
8 – 10 N·m {80 – 100 kgf·cm}
If the difference in the number of chainring teeth is 13T – 16T, make the chain
one link longer than this.
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
3-77 Oimatsu-cho, Sakai-ku, Sakai, Osaka 590-8577, Japan
Jan. 2008 by Shimano Inc. PIT. SZK. Printed in Japan
C
These service instructions are printed on recycled paper.
Please note: Specifications are subject to change for improvement without notice. (English)
Produkt Specifikationer
| Mærke: | Shimano |
| Kategori: | Cykel tilbehør |
| Model: | CT-S500 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Shimano CT-S500 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Cykel tilbehør Shimano Manualer
4 Oktober 2024
30 September 2024
16 September 2024
14 September 2024
11 September 2024
6 September 2024
5 September 2024
13 August 2024
13 August 2024
8 August 2024
Cykel tilbehør Manualer
- Cykel tilbehør Silverline
- Cykel tilbehør Garmin
- Cykel tilbehør Thule
- Cykel tilbehør SKS
- Cykel tilbehør Abus
- Cykel tilbehør Crivit
- Cykel tilbehør Stanley
- Cykel tilbehør Trelock
- Cykel tilbehør Bontrager
- Cykel tilbehør AXA
- Cykel tilbehør Fiamma
- Cykel tilbehør Hema
- Cykel tilbehør Lezyne
- Cykel tilbehør Prophete
- Cykel tilbehør Valk
- Cykel tilbehør Kemo
- Cykel tilbehør Kayoba
- Cykel tilbehør Topeak
- Cykel tilbehør Knog
- Cykel tilbehør Vaude
- Cykel tilbehør Giant
- Cykel tilbehør Dnt
- Cykel tilbehør Basil
- Cykel tilbehør IXS
- Cykel tilbehør Ergon
- Cykel tilbehør MOTO
- Cykel tilbehør KLICKfix
- Cykel tilbehør Evoc
- Cykel tilbehør Spokey
- Cykel tilbehør SECURITY Plus
- Cykel tilbehør AARON
- Cykel tilbehør Pletscher
- Cykel tilbehør Funn
Nyeste Cykel tilbehør Manualer
26 September 2024
24 September 2024
14 September 2024
13 September 2024
13 September 2024
5 September 2024
5 September 2024
2 September 2024
2 September 2024
31 August 2024